Honeywell T775M Manual del propietario
To program the controller, perform the following procedures in the order listed:
Fig. 1
Press the MENU button, then select PROGRAM and press the button to view the
program menu.
Fig. 1 shows the Program menu for controller.
Fig. 2
1. From the menu, use the and buttons to highlight MOD 1.
2. Press the button to select MOD 1 to view the parameters. Fig. 2 shows
RELAY 1. In MOD 1, THROT RNG replaces DIFFERNTL.
!"#
Fig. Program – Setpoint
1. From the menu, use the and buttons to highlight SETPOINT.
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 55°F.
4. Press the button to accept the setpoint temperature and display the next
option.
!"$%&'!"$&"$
Fig. Program – Throttling Range
1. From the menu, use the and buttons to highlight THROT RNG.
2. Press the button to display the throttling range value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
( " &
Fig. Program – Sensor
1. From the menu, use the and buttons to highlight SENSOR.
2. Press the button to display the sensor selections.
3. Use the and buttons to select Sensor A or B.
Select sensor B.
4. Press the button to accept the highlighted sensor and display the next option.
)%*'
Fig. Program Heat/Cool
1. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
2. Press the button to display the heat and cool selections.
3. Use the and buttons to select Heat or Cool.
Select COOL.
4. Press the button to accept the highlighted selection and display the next
option.
+
Press the button to accept the highlighted selection EXIT. This will display the main
Program Menu screen (Fig. 1)
Fig. 1
("+,#-
1. From the menu, use the and buttons to highlight MOD 2.
2. Press the button to select MOD 2 to view the parameters.
( !"#
Fig. Program - Setpoint
1. From the menu, use the and buttons to highlight SETPOINT.
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 55°F.
4. Press the button to accept the setpoint temperature and display the next
option.
( !"$%&'!"$&"$
Fig. Program – Throttling Range
1. From the menu, use the and buttons to highlight THROT RNG.
2. Press the button to display the throttling range value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
(( " &
Fig. Program – Sensor
5. From the menu, use the and buttons to highlight SENSOR.
6. Press the button to display the sensor selections.
7. Use the and buttons to select Sensor A or B.
Select sensor A.
8. Press the button to accept the highlighted sensor and display the next option.
()%*'
Fig. Program Heat/Cool
5. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
6. Press the button to display the heat and cool selections.
7. Use the and buttons to select Heat or Cool.
Select HEAT.
8. Press the button to accept the highlighted selection and display the next
option.
_____________________________________________________________________
(+
Press the button to accept the highlighted selection EXIT. This will display the main
Program Menu screen (Fig. 1)
Fig. 1
)"+,&'.-
1. From the menu, use the and buttons to highlight RELAY 1.
Fig. 2
2. Press the button to select RELAY 1 to view the parameters.
) !"&'.
Fig. Program - Setpoint
1. From the menu, use the and buttons to highlight SETPOINT (Fig. 2).
2. Press the button to display the setpoint value.
3. Use the and buttons to increase/decrease the desired setpoint
temperature.
Set the temperature to 100°F.
4. Press the button to accept the setpoint temperature and display the next
option.
_____________________________________________________________________
)#!&"!' !"$
Fig. Program – Differential
1. From the menu, use the and buttons to highlight DIFFERNTL.
2. Press the button to display the differential value.
3. Use the and buttons to increase/decrease the desired value.
Set the value to 10°F.
4. Press the button to accept the value and display the next option.
)( " &
Fig. Program – Sensor
1. From the menu, use the and buttons to highlight SENSOR.
2. Press the button to display the sensor selections.
3. Use the and buttons to select Sensor A or B.
Select sensor A.
4. Press the button to accept the highlighted sensor and display the next option.
))%*'
Fig. Program Heat/Cool
1. From the menu, use the and buttons to highlight HEAT/COOL (Default:
HEAT).
2. Press the button to display the heat and cool selections.
3. Use the and buttons to select Heat or Cool.
Select HEAT.
4. Press the button to accept the highlighted selection and display the next
option.
+
Fig. Program – Exit
Press the HOME button to leave programming mode and return to the home screen.
This completes the programming procedure.
Tabla de contenidos
Otros manuales de Controladores de Honeywell
Honeywell
Honeywell SUPER TRADELINE S8610U Manual de usuario
Honeywell
Honeywell INCOMM L510 Manual de usuario
Honeywell
Honeywell ML7284 Manual de operación
Honeywell
Honeywell CENTRALINE EAGLE Manual de usuario
Honeywell
Honeywell WEBsAX Series Guía
Honeywell
Honeywell V4055A Manual de operación
Honeywell
Honeywell UDC 2300 Manual de usuario
Honeywell
Honeywell MS7103 Series Manual de usuario
Honeywell
Honeywell MSR PolyGard 2 MGC2-K Manual de usuario
Honeywell
Honeywell HC900 Manual de uso y cuidado
Honeywell
Honeywell T775U Series Manual de usuario
Honeywell
Honeywell V9055A Manual de usuario
Honeywell
Honeywell AUTOMATIC CONTROL Manual de instalación y operación
Honeywell
Honeywell VB6 Series Manual de usuario
Honeywell
Honeywell HCE80R Manual de usuario
Honeywell
Honeywell UDC3300 Manual de usuario
Honeywell
Honeywell AQS51-KAM Manual de operación
Honeywell
Honeywell AQUASTAT L4188A Manual de usuario
Honeywell
Honeywell UDC3300 Manual de usuario
Honeywell
Honeywell BC7000L1000 Manual
