Honeywell 10260A Series Guía

62-86-33-41 Page 1 of 5

10260A Series Actuator

1000 Ohm Potentiometer Kit

Replacement Instructions

51451656-507

Document Number

Form: 62-86-33-41

Effective: 08-4-05

Supersedes: None

Summary

This kit contains a new potentiometer and associated parts for your 10260A Actuator.

Tools Needed

To perform the installation procedure, you will need the following tools:

• Medium Flat-blade screwdriver

• Medium Phillips screwdriver

• Small needle-nosed pliers

Procedure

WARNING

Disconnect power before accessing components inside the actuator. Failure to do so may result in death or

serious injury.

ATTENTION

When working with Printed Wiring Assemblies (PWAs) always protect against electrostatic discharge by

wearing a grounded wrist strap. Failure to do so may result in equipment damage.

Page 2 of 5 62-86-33-41

Table 1 1000 Ohm Installation Procedure

Step Action

1 Remove covers

Remove all 3 covers (top and both rear covers)

2 Remove potentiometer

Disconnect potentiometer wires at the terminal board. (Terminals 32, 33, 34, 35, 36 and 37. )

Disconnect potentiometer from mounting plate. Save the nuts for next step.

3 Mount the new potentiometer using saved nuts.

4 Slide the potentiometer actuator sleeve through the potentiometer and over the end of the cam bushing.

Push the sleeve in potentiometer fitting the pin into the slot of the potentiometer.

62-86-33-41 Page 3 of 5

Step Action

5 Connect wires.

Feed the potentiometer wires down from the upper casting cavity to the lower cavity. Connect the

potentiometer wires to the appropriate terminals using the wiring table below.

Wire Color Terminal

Red TB4-32

Blue TB4-33

Green TB4-34

Black TB4-35

White TB4-36

Yellow TB4-37

6 Position actuator to 50% of span. Pointer may be on either the right or left side of the scale. Pointer as

shown is on the left side of the scale.

Page 4 of 5 62-86-33-41

Step Action

7 Calibrate the potentiometer.

Connect a multi meter set to ohms ( Ω) to terminals TB4-35 & TB4-36.

Use a small allen wrench in the hole on the potentiometer actuator sleeve to turn the potentiometer.

Adjust the potentiometer to 500 Ω+/- 5 Ω.

Install the set screw.

When the potentiometer is set for 500 Ωtighten the set screw.

8 Replace the gasket.

9 Re-attach the top cover.

Industrial Measurement and Control

Honeywell

1100 Virginia Drive

Fort Washington, PA 19034

62-86-33-41 08/05 Printed in USA www.honeywell.com/imc

Warranty/Remedy

Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship.

Contact your local sales office for warranty information. If warranted goods are returned to Honeywell

during the period of coverage, Honeywell will repair or replace without charge those items it finds defective.

The foregoing is Buyer's sole remedy and is in lieu of all other warranties, expressed or implied,

including those of merchantability and fitness for a particular purpose. Specifications may change

without notice. The information we supply is believed to be accurate and reliable as of this printing.

However, we assume no responsibility for its use.

While we provide application assistance personally, through our literature and the Honeywell web site, it is

up to the customer to determine the suitability of the product in the application.

Tabla de contenidos

Otros manuales de Controladores de Honeywell

Honeywell

Honeywell PEHA D CDH8U5 Series Manual de instalación y operación

Honeywell

Honeywell HR 40 Manual de usuario

Honeywell

Honeywell MS7510A2008 Manual de usuario

Honeywell

Honeywell ML7425A Series Manual de operación

Honeywell

Honeywell 2RM7800L1087 Manual de servicio

Honeywell

Honeywell UDC 2300 Manual de usuario

Honeywell

Honeywell DC1000 SERIES Manual de usuario

Honeywell

Honeywell HJK7000 UltraKey Plus Manual de instrucciones

Honeywell

Honeywell M7061 Manual de usuario

Honeywell

Honeywell VaporStat L408J Manual de usuario

Honeywell

Honeywell VC6613AJ1000 Manual de usuario

Honeywell

Honeywell T775B Guía de instalación

Honeywell

Honeywell V8200 Manual de usuario

Honeywell

Honeywell ML4195E Manual de usuario

Honeywell

Honeywell H808C Manual de usuario

Honeywell

Honeywell Satronic DVI 980 Manual de usuario

Honeywell

Honeywell UDC3500 Manual de usuario

Honeywell

Honeywell T6590A Manual de usuario

Honeywell

Honeywell HON 372 Manual

Honeywell

Honeywell T775A Manual de usuario

Honeywell

Honeywell DC33XB Manual de usuario

Honeywell

Honeywell S9200U1000 Manual de usuario

Honeywell

Honeywell ZG 215VN Manual de usuario

Honeywell

Honeywell LYNX Touch L5200 Series Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario