Honeywell Fire-Lite ECC-RPU Manual técnico

One Fire-Lite Place

Northford, CT 06472-1653 USA

203-484-7161 • FAX 203-484-7118

www.firelite.com

ECC-RPU Remote Page Unit

Product Installation Document

PN LS10030-000FL-E:B 8/9/2013 13-696

1Overview

The ECC-RPU is an optional Remote Page Unit

compatible with the ECC-50/100 Emergency Command

Center. The ECC-RPU provides 8 message select buttons.

The 9th button can be used to activate an MMF-300

monitor module mounted inside the cabinet. The RPU

requires an external data bus connection, an external audio

riser connection, and an external operator interface power

connection (24 volts DC) from the ECC-50/100 main

console. ALL CALL paging can be broadcast over the

speaker circuits by depressing the microphone's push-to-

talk switch. Refer to the ECC-50/100 Manual, LS10001-

000FL-E, for more information.

NOTE: Installation and wiring of this device must be

done in accordance with NFPA 72 and local ordinances.

2Installation

2.1 Removing the Dress Panel

1. Open the door and lift the door off the pin hinges.

2. Loosen the screw securing the dress panel to the

backbox.

3. Open dress panel and disconnect the ground wire

from the back.

4. Lift up dress panel and pull out lower pivot flange.

Slide the upper pivot flange down to completely

remove the dress panel from cabinet. Store in a safe

location.

2.2 Mounting the Backbox

1. Mark and predrill holes for the top two backbox

keyhole mounting bolts using the dimensions shown.

2. Install two upper fasteners in the wall with the screw

heads protruding.

3. Using the upper 'keyholes', mount the backbox over

the two screws.

4. Mark and drill the lower two holes.

5. Install the remaining fasteners and tighten all

fasteners to complete backbox mounting.

6. Carefully reinstall the dress panel by reversing the

steps in Section 2.1. Remember to reattach the

ground cable.

7. Reinstall door.

A trim ring, TR-6-R, is available for semi-flush mount

installations.

Figure 1 ECC-RPU

screw

location

Figure 2 Removing the Dress Panel

1. lift up

2. pull out

3. slide down

keyholes

10.0” (25.4cm) O.C.

lower mounting holes

Figure 3 Backbox Mounting

2ECC-RPU Installation Document — P/N LS10030-000FL-E:B 8/9/2013

2.3 Mounting/Wiring an Optional

Monitor Module

An MMF-300 monitor module may be mounted inside the

cabinet. This can be used for HVAC shutdown

applications when the monitor module is connected to the

FACP SLC polling loop. The monitor module is wired to

TB4 on the RPU and is activated by the 9th button on the

RPU keypad. The module’s LED is visible through the

keypad next to the 9th button.

1. Remove the two (2) keps nuts that secure the RPU

board to the dress panel using a 5/16” socket.

2. Set the SLC address on the MMF-300. Remove the

four (4) break-away tabs from the monitor module.

See Figure 4.

3. Insert the bottom of the monitor module (SLC address

dials facing inward) into the mounting tabs on the left

side of the RPU. The RPU mounting screws will go

through the top of the monitor module. Situate the

LED on the front of the module over the hole in the

PC board.

4. Replace the keps nuts over the mounting screws to

secure the monitor module to the board.

5. Connect the SLC wiring to the module terminals 1 (–)

and 2 (+). Refer to the SLC Wiring Manual for more

information.

6. Wire TB4 on the RPU to T6/T7 on the monitor

module as shown below. No ELR is required as it is

built into TB4.

3 Wiring

Connections are made from TB24, TB12, and TB22 on the

ECC-50/100 main control board to TB1, TB3, and TB2 on

the RPU. If the ECC-RPU is the last device on the audio

and data bus chain, signal terminations are required. For

the last device on the external data bus, a removable

jumper must be on pins 1 and 2 of JS4. If the ECC-RPU is

not the last device, the jumper must be on pins 2 and 3 of

JS4 as shown below. For the external audio riser,

termination (15K ohm resistor) must be connected to pins

4 and 5 on TB2. A ferrite clamp (P/N: 50116546-001)

must be installed around all wires in both the input and

output wire runs inside the RPU cabinet as shown below.

+ -

SLC In

SLC Out

mounting

tabs

TB4

keps

nuts

Figure 4 Wiring an MMF-300 to the RPU

Remove

break-away

tabs (4) from

module

LED on other

side of module

ECC main

control board

RPU board

TB24

TB12

TB22

TB1

TB3

TB2

external operator interface

power - 24VDC

external

data bus

external

audio

riser

Figure 5 Remote Page Unit Wiring

(Class B/Style Y)

to next operator interface/

amplifier or 15KELR

(if last device)

JS4

(shown jumpered

on pins 2 and 3)

24V

OUT

Data

OUT

Audio

OUT

ferrite clamp

ECC-RPU Installation Document — P/N LS10030-000FL-E:B 8/9/2013 3

4 LED Indicators

OK to Page A green LED that turns on steady to

instruct the operator that he/she may start paging.

Mic Trouble A yellow LED that turns on steady to

indicate a microphone wiring fault.

Power A green LED that turns on steady when DC

power is present.

Data Bus Fault A yellow LED turns on steady when

the main console and RPU cannot communicate.

Audio Riser Fault A yellow LED that turns on steady

when the audio riser wiring is open or short-circuited.

Board Fault A yellow LED that turns on steady when a

critical issue has been detected with the board. There are

no serviceable parts. Contact service personnel to replace

the unit.

5 Slide-in Label

Carefully cut along the outside of the label. Identify

keypad buttons as desired and slide the label upwards

through the slot at the bottom of the keypad.

ECC main

control board

RPU board

TB24

TB12

TB22

external operator interface

power - 24VDC

external

data bus

external

audio

riser

Figure 6 Remote Page Unit Wiring

(Class A/Style Z)

TB1

TB3

TB2

24V

OUT

Data

OUT

Audio

OUT

ferrite clamp

OK TO PAGE

MIC TROUBLE

POWER

DATA BUS FAULT

AUDIO RISER FAULT

BOARD FAULT

Tabla de contenidos

Otros manuales de Unidad de control de Honeywell

Honeywell

Honeywell V5011N Manual de usuario

Honeywell

Honeywell BA295S Manual de usuario

Honeywell

Honeywell Pro-Watch 6000 Manual de usuario

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell V48F Manual de operación

Honeywell

Honeywell TELEPHONE ACCESS MODULE W8735D Manual de usuario

Honeywell

Honeywell D05FT Manual de usuario

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell IDENT KEY 3 Manual de usuario

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell SmartValve SV9520H Manual de usuario

Honeywell

Honeywell T7270A2001 Manual de usuario

Honeywell

Honeywell BA295 Compact Manual de usuario

Honeywell

Honeywell SK-Mon-10 Manual de usuario

Honeywell

Honeywell TC810E1040 Manual de usuario

Honeywell

Honeywell MDC108200 Manual de usuario

Honeywell

Honeywell krom schroeder IFD 258 Manual de usuario

Honeywell

Honeywell 7800 SERIES Manual de usuario

Honeywell

Honeywell BA295STN-A Series Manual de usuario

Honeywell

Honeywell NetAXS-123 Manual de usuario

Honeywell

Honeywell TrueZONE ARD Series Manual de usuario

Honeywell

Honeywell ADEMCO 4229 Instrucciones de montaje

Honeywell

Honeywell REDLINK ERM5220R Manual de operación

Honeywell

Honeywell S89C Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario