Honeywell PRO4200 Manual de usuario
September 2020 © 2020Honeywell International, Inc. All rights reserved 800-25698V1 I
-
PRO4200
Two Reader Module
(PRO42R2)
Installation Guide
September 2020 © 2020Honeywell International, Inc. All rights reserved 800-25698V1 II
-
Copyright© 2020 Honeywell. All rights reserved.
All product and brand names are the service marks, trademarks, registered trademarks, or registered
service marks of their respective owners. Printed in the United States of America. Honeywell reserves the
right to change any information in this document at any time without prior notice.
WIN-PAK® is a trademark of Honeywell International, Inc.
Ordering Information
Please contact your local Honeywell representative or visit us on the web at www.honeywellaccess.com
for information about ordering.
Feedback
Honeywell appreciates your comments about this manual. Please visit us on the web at
www.honeywellaccess.com to post your comments.
Discover | Customer Portal
Self-Service Product Support and Learning Management System
https://honeywelldiscovertraining.com/login/discover/default.asp
YouTube | Honeywell Help and Support
https://www.youtube.com/channel/UCBEL6ouNV_LN5lEpYRujMTg/featured
PRO4200 Two-Reader Module User Guide, Document 800-25698V1 iii
Notices
Warnings and Cautions.................................................................................................... . . . . . . . . . . v
Disclaimer.......................................................................................................................... . . . . . . . . . . vi
Compliance........................................................................................................................ . . . . . . . . . vii
CE and WEEE Marking .................................................................................................. . . . . . . . . . vii
Unpacking Procedure....................................................................................................... . . . . . . . . . vii
Shipping Instructions ....................................................................................................... . . . . . . . . . . ix
Limited Warranty ............................................................................................................. . . . . . . . . . . ix
Confidentiality .................................................................................................................. . . . . . . . . . . x
Installing the PRO4200 Two Reader Module
Description ........................................................................................................................ . . . . . . . . . 11
Specification...................................................................................................................... . . . . . . . . . 12
Set Up................................................................................................................................. . . . . . . . . . 13
LED Operation.................................................................................................................. . . . . . . . . . 15
Power.................................................................................................................................. . . . . . . . . . 16
Communications............................................................................................................... . . . . . . . . . 16
Wiring ................................................................................................................................ . . . . . . . . . 17
Wiring Diagram for Connectors TB1,TB7-9 ............................................................... . . . . . . . . . 18
2-Reader Input Module Programming Guide
............................................................................................................................................. . . . . . . . . . 25
CONTENTS
iv www.honeywell.com
(This page is left blank intentionally for double-sided printing.)
Notices
Warnings and Cautions
PRO4200 Two-reader Module User Guide, Document 800-25698V1 v
Notices
Warnings and Cautions
Warning
Before connecting the device to the power supply, verify that the output voltage is
within specifications of the power supply.
Do not apply power to the system until after the installation has been completed.
Personal injury or death could occur, and the equipment could be damaged beyond
repair, if this precaution is not observed!
Warning: Fire Safety and Liability Notice
Never connect card readers to any critical entry, exit door, barrier, elevator, or gate
without providing an alternative exit in accordance with all fire and life safety codes
pertinent to the installation. These fire and safety codes vary from city to city and you
must get approval from local fire officials whenever using an electronic product to
control a door or other barrier. Use of egress buttons, for example, may be illegal in
some cities. In most applications, single action exit without prior knowledge of what
to do is a life safety requirement. Always make certain that any required approvals are
obtained in writing. DO NOT ACCEPT VERBAL APPROVALS, BECAUSE THEY
ARE NOT VALID.
Honeywell never recommends using the PRO4200 or related products for use as a
primary warning or monitoring system. Primary warning or monitoring systems
should always meet local fire and safety code requirements. The installer must also
test the system on a regular basis by instructing the end user in appropriate daily
testing procedures. Failure to test a system regularly could make the installer liable for
damages to the end user if a problem occurs.
Note: See the Remote Enclosure Installation manuals PRO22ENC1, PRO22ENC2,
PRO22ENC3 or PRO22ENC5 for installation instructions.
Warning:
EARTH ground all enclosures for proper installation.
Warning:
Use suppressors on all door strikes. Use S-4 suppressors for installation. Honeywell
recommends only DC strikes.
Warning: For UL Installations:
• Wiring methods shall be in accordance with the National Electrical Code
(ANSI/NFPA70).
• All interconnecting devices must be UL Listed.
• Not Evaluated by UL for fire, life safety, or burglary applications.
• Do Not Connect To A Receptacle Controlled By A Switch.
Notices
Disclaimer
vi www.honeywell.com
• All interconnecting wire must be UL/ULC Listed, rated and suitable for the
use.
Caution:
IF ANY DAMAGE TO THE SHIPMENT IS NOTICED, A CLAIM MUST BE
FILED WITH THE COMMERCIAL CARRIER RESPONSIBLE.
Caution: Electrostatic discharge can damage CMOS integrated circuits and modules.
To prevent damage, always follow these procedures:
• Use static shield packaging and containers to transport all electronic
components, including completed reader assemblies.
• Handle all ESD sensitive components at an approved static-controlled
workstation. These workstations consist of a desk mat, a floor mat, and an ESD
wrist strap. Workstations are available from various vendors.
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
Note: This document and the data in it shall not be duplicated, used, or disclosed to
others for procurement or manufacture, except as authorized by and with the written
permission of, Honeywell, Inc. The information contained in this document or in the
product itself is considered the exclusive property and trade secrets of Honeywell, Inc.
Copyright laws of the United States protect all information in this document or in the
software product itself.
Note: Any use of this product is subject to the terms and acceptance of the Honeywell,
Inc. Software Agreement. Please request a copy from Honeywell, Inc., and review the
agreement carefully.
Disclaimer
Product Liability; Mutual Indemnification
In the event that a Customer receives a claim that a Product or any component thereof
has caused personal injury or damage to property of others, Customer shall
immediately notify Honeywell in writing of all such claims. Honeywell shall defend
or settle such claims and shall indemnify and hold Customer harmless for any costs or
damages including reasonable attorneys' fees which Customer may be required to pay
as a result of the defective Product or the negligence of Honeywell, its agents, or its
employees.
Customer shall hold harmless and indemnify Honeywell from and against all claims,
demands, losses, and liability arising out of damage to property or injury to persons
Notices
Compliance
PRO4200 Two-reader Module User Guide, Document 800-25698V1 vii
occasioned by or in connection with the acts or omissions of Customer and its agents
and employees, and from and against all claims, demands, losses, and liability for
costs of fees, including reasonable attorneys' fees, in connection therewith.
Compliance
To obtain applicable EU compliance Declaration of Conformities for this product,
please refer to our website,
https://www.security.honeywell.com/All-Categories/access-control-systems/control-p
anels-hardware. For any additional information regarding the compliance of this
product to any EU-specific requirements, please contact:
Honeywell Security & Communications
Honeywell Security - Quality Assurance Dept., Newhouse Industrial Estate
Motherwell
Lanarkshire ML1 5SB
Scotland
United Kingdom
Tel: +44(0) 1698 738200
Email: [email protected]
CE and WEEE Marking
Description of the used symbol.
Unpacking Procedure
Caution:
If any damage to the shipment is noticed before unpacking, a claim must be filed with
the commercial carrier.
All containers should be opened and unpacked carefully in order to prevent damage to
the contents.
The following steps are used to unpack equipment in preparation for installation:
1. Open the container and remove the unit(s) and all packing material. Retain the
container and all packing materials. They may be used again for reshipment of
the equipment, if needed.
2. Inspect the contents for shortage. If items are missing items, contact the order
entry department at 800-323-4576.
3. Visually check contents. If damage is discovered, perform the following:
CE -Standard -Logo. This product complies with
the harmonized Regulation of the EU
WEEE symbol.It indicates this product is to be
recycling and not been thrown in the dustbin
Notices
Unpacking Procedure
viii www.honeywell.com
• If shipping caused damage to the unit, a claim must be filed with the
commercial carrier.
• If any other defect is apparent, call for a return authorization.
Notices
Shipping Instructions
PRO4200 Two-reader Module User Guide, Document 800-25698V1 ix
Shipping Instructions
To ship equipment back to Honeywell, Inc.:
1. Contact the customer service department at 800-323-4576 before returning
equipment. When you call please have available:
• A description of the problem or reason you are returning the equipment.
• Your original purchase order number, invoice number and if the unit is
still under warranty.
• A new purchase order number if the unit is not under warranty.
2. From the customer service department, obtain the Return Authorization
Number (RMA).
3. Show the RMA number on all packages shipped. Packages which are not
marked with an RMA number will be refused at the factory and returned to
you COD.
4. Carefully pack the equipment for shipment. Use the original packing material
whenever possible.
Limited Warranty
All Products sold or licensed by Honeywell include a warranty registration card which
must be completed and returned to Honeywell by or on behalf of the end user in order
for Honeywell to provide warranty service, repair, credit or exchange. All warranty
work shall be handled through Customer which shall notify Honeywell and apply for a
Return Merchandise Authorization (RMA) number prior to returning any Product for
service, repair, credit, or exchange. Honeywell warrants that its Products shall be free
from defects in materials and workmanship for a period of two years from date of
shipment of the Product to Customer. The warranty on Terminals, Printers,
Communications Products and Upgrade kits is 90 days from date of shipment.
Satisfaction of this warranty shall be limited to repair or replacement of Products
which are defective or defective under normal use. Honeywell's warranty shall not
extend to any Product which, upon examination, is determined to be defective as a
result of misuse, improper storage, incorrect installation, operation or maintenance,
alteration, modification, accident or unusual deterioration of the Product due to
physical environments in excess of the limits set forth in Product manuals. THERE
ARE NO WARRANTIES WHICH EXTEND BEYOND THIS PROVISION. THIS
WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS,
IMPLIED OR STATUTORY, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. NO
REPRESENTATION OR WARRANTY OF THE DISTRIBUTOR SHALL EXTEND
THE LIABILITY OR RESPONSIBILITY OF THE MANUFACTURER BEYOND
THE TERMS OF THIS PROVISION. IN NO EVENT SHALL HONEYWELL BE
LIABLE FOR ANY RE-PROCUREMENT COSTS, LOSS OF PROFITS, LOSS OF
USE, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES TO ANY
PERSON RESULTING FROM THE USE OF HONEYWELL'S PRODUCTS.
Notices
Confidentiality
xwww.honeywell.com
Confidentiality
All software, drawings, diagrams, specifications, catalogs, literature, manuals and
other materials furnished by Honeywell relating to the design, use and service of the
Products shall remain confidential and shall constitute proprietary rights of Honeywell
and Customer agrees to treat such information as confidential. Customer shall acquire
no rights in the design of the Products or the related materials except to use such
information solely for the purpose of and only during the time it sells the Products.
Customer shall not copy the design of any of the Products or use or cause to be used
any Product design or related materials for its own benefit or for the benefit of any
other party. The covenants contained in this section shall remain effective throughout
the term of this Agreement and thereafter unless specifically waived by Honeywell in
writing.
Otros manuales para PRO4200
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Unidad de control de Honeywell
Honeywell
Honeywell D05FS Manual de usuario
Honeywell
Honeywell ESSER IQ8MCP Manual de usuario
Honeywell
Honeywell Ex-Or MLSUC500 Manual de usuario
Honeywell
Honeywell Silent Knight IDP-Monitor-2 Manual de usuario
Honeywell
Honeywell M5410C1001 Manual de usuario
Honeywell
Honeywell NOTIFIER M701E Manual de usuario
Honeywell
Honeywell JADE W7220 Manual de operación
Honeywell
Honeywell L5000-Wi-Fi Manual de usuario
Honeywell
Honeywell Compact Corona Series Manual de operación
Honeywell
Honeywell ADEMCO 4204 Manual de usuario
Honeywell
Honeywell SDW 10 Manual de servicio
Honeywell
Honeywell L506 Manual de usuario
Honeywell
Honeywell V5832B Manual de operación
Honeywell
Honeywell FIRE-LITE-ALARMS CMF-300 Manual de usuario
Honeywell
Honeywell FV300 Manual de usuario
Honeywell
Honeywell Braukmann DR300 Manual de usuario
Honeywell
Honeywell SG160S Manual de usuario
Honeywell
Honeywell Braukmann D06G Manual de usuario
Honeywell
Honeywell RK-MCU Hoja de instrucciones
Honeywell
Honeywell RM7800L1087 Manual de usuario
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
