Honeywell Voyager 9520/40 Manual de usuario
Voyager 9520/40
Voyager GS9590
Eclipse 5145
Quick Start Guide
VG-ECL-QS Rev C
6/12
Aller à www.honeywellaidc.com pour le français.
Vai a www.honeywellaidc.com per l'italiano.
Gehe zu www.honeywellaidc.com für Deutsch.
Ir a www.honeywellaidc.com para español.
Para Português, acesse www.honeywellaidc.com.br.
Перейти на русскоязычный сайт www.honeywellaidc.com.
日本語 : www.honeywellaidc.com をご覧ください。
如要到中国 www.honeywellaidc.com（简体）。
한글 www.honeywellaidc.com 로이동합니다 .
Getting Started
Turn off the computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
Connecting the Scanner
USB:
Serial
(RS232):
Keyboard
Wedge:
optional adapter cable
Reading Techniques
Recall Defaults
Scan Enable Factory Defaults, then Recall Defaults to reset all
standard product default settings.
Interface Selections
USB
³999998
Recall Defaults
³846600
Enable Factory Defaults
³999970
³316400
USB Keyboard
Emulation
Load Integrated Full
Speed USB IBM/OEM
Defaults
³316460
USB Serial Emulation
Keyboard Wedge
Keyboard Country
Scan a bar code to select one of the following keyboard country
templates. Refer to your Configuration Guide for additional keyboard
country settings.
³5155143
Keyboard Wedge Emulation
³416210
³416220
United Kingdom
³416230
Germany/Austria
France
³416260
United States
³416200
Belgium
³416250
Spain
³416240
Italy
ALT Mode
If your bar code contains special characters from the extended ASCII
chart, for example, an e with an accent grave (è), scan the ALT Mode
On bar code. The data is then output with the special character(s).
Note: Scan ALT mode after scanning the appropriate Keyboard
Country code.
RS232 Communication Commands
³116217
ALT Mode On
³115816
RTS/CTS
Handshaking On
³115914
XON/XOFF On
³115913
ACK/NAK On
³116013
8 Data Bits
³116014
1 Stop Bit
³316045
No Parity
Prefix
Scan one of the following bar codes to program your scanner to add
or remove a start of text character, or AIM, NCR, or Nixdorf
identification characters before each bar code.
³116615
³116605
³107905
³107901
STX Prefix On
STX Prefix Off
³107915
AIM ID Prefix On
AIM ID Prefix Off
³107911
NCR Prefix On
NCR Prefix Off
³107907
³107917
Nixdorf Prefix On
Nixdorf Prefix Off
Suffix
Scan one of the following bar codes to program your scanner to add
or remove a carriage return, line feed, tab, or end of text after each
bar code.
³116613
³116603
³116604
CR Suffix On
CR Suffix Off
³116612
LF Suffix On
³116602
LF Suffix Off
³116610
Tab Suffix On
³116600
Tab Suffix Off
³116614
ETX Suffix On
ETX Suffix Off
User Configurable Prefix/Suffix
One or two prefix or suffix characters can be added and assigned for
data transmission. Use one of the codes below with a 3 code byte
sequence that represents the desired character (see ASCII
Conversion Chart, end of document) for your prefix or suffix. (To add
additional prefix/suffix characters, refer to your Single-Line
Configuration Guide.)
Scan the Enter/Exit Programming bar code to begin. Then scan
the 3 digit decimal equivalent of the ASCII character into the
appropriate character location with the code byte bar codes (see
Code Bytes, end of document). To save, scan the Enter/Exit
Programming bar code again.
Example: To add an asterisk (*) as a prefix, scan the bar codes:
1. Enter/Exit Programming
2. Configurable Prefix #1
3. Code Byte 0
4. Code Byte 4
5. Code Byte 2
6. Enter/Exit Programming
³904500
Configurable Suffix #1
³904600
Configurable Suffix #2
³903500
Configurable Prefix #1
³903600
Configurable Prefix #2
³999999
Enter/Exit Programming
Supplements
Scan one of the bar codes below to program your scanner for 2 or 5
digit bar code supplements.
977 (2 Digit) Supplement Required: Turn on this feature when a 2
digit supplement is required for EAN-13 codes that begin with 977.
³101217
2 Digit Supplements
On
³101207
2 Digit Supplements Off
³101216
5 Digit Supplements
On
³101206
5 Digit Supplements Off
³101314
977 Supplements On
³101304
977 Supplements Off
UPC/EAN Formatting
Scan Convert UPC-A to EAN-13 and a leading zero is transmitted
before a UPC-A bar code to convert it to EAN-13.
Scan Transmit Lead Zero on UPC-E to transmit a zero before each
UPC-E bar code.
Scan Transmit UPC-A Number System to transmit the UPC-A
leading digit with the bar code data. To transmit just the data, without
the leading digit, scan Don’t Transmit UPC-A Number System.
³107514
Convert UPC-A to
EAN-13
³107504
Don’t Convert UPC-A to
EAN-13
³107513
Transmit Lead Zero on
UPC-E
³107503
Don’t Transmit Lead
Zero on UPC-E
³107511
³107501
Don’t Transmit UPC-A
Number System
Transmit UPC-A
Number System
Este manual sirve para los siguientes modelos
7
Tabla de contenidos
Otros manuales de Lector de código de barras de Honeywell
Honeywell
Honeywell QUANTUME IS3480 Manual de usuario
Honeywell
Honeywell 3800G04-USBKITE Manual de usuario
Honeywell
Honeywell SF61 Manual de usuario
Honeywell
Honeywell Solaris MS7820 Manual de usuario
Honeywell
Honeywell 1900GHD-2 Manual de usuario
Honeywell
Honeywell PX4-6IE-CUTR-IG-1 Manual de usuario
Honeywell
Honeywell VoyagerGS MS9590i Manual de usuario
Honeywell
Honeywell IT3800 Manual de usuario
Honeywell
Honeywell MS9520 Voyager Manual de usuario
Honeywell
Honeywell IS4921 Guía de configuración rápida
Honeywell
Honeywell Solaris MS7820 Manual de usuario
Honeywell
Honeywell Quantum T 3580 Manual de usuario
Honeywell
Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Manual de usuario
Honeywell
Honeywell MS9500 Voyager Series Manual de usuario
Honeywell
Honeywell 1400gPDF Manual de usuario
Honeywell
Honeywell N431X Manual de usuario
Honeywell
Honeywell 3820 Manual de usuario
Honeywell
Honeywell 4600g Manual de usuario
Honeywell
Honeywell Orbit MS7120 Manual de usuario
Honeywell
Honeywell MX7 Tecton Manual de usuario
