Honeywell 2020-5 Manual de usuario
™
2020/3820/3820i
Cordless System
User’s Guide
Disclaimer
Honeywell International Inc. (“Honeywell”) reserves the right to make changes
in specifications and other information contained in this document without prior
notice, and the reader should in all cases consult Honeywell to determine
whether any such changes have been made. The information in this publication
does not represent a commitment on the part of Honeywell.
Honeywell shall not be liable for technical or editorial errors or omissions con-
tained herein; nor for incidental or consequential damages resulting from the
furnishing, performance, or use of this material.
This document contains proprietary information that is protected by copyright.
All rights are reserved. No part of this document may be photocopied, repro-
duced, or translated into another language without the prior written consent of
Honeywell.
©2004-2011 Honeywell International Inc. All rights reserved.
Other product names or marks mentioned in this document may be trademarks
or registered trademarks of other companies and are the property of their
respective owners.
Web Address: www.honeywellaidc.comw.honeywell.com/aidc
Microsoft® Windows® and the Windows logo are trademarks or registered
trademarks of Microsoft Corporation.
The
Bluetooth
®word mark and logos are owned by Bluetooth SIG, Inc.
Product Agency Compliance
USA
FCC Part 15 Subpart C
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
Caution: Any changes or modifications made to this equipment not
expressly approved by Honeywell may void the FCC authorization
to operate this equipment.
Use only shielded data cables with this system. This unit has been tested
with cables less than 3 meters. Cables greater than 3 meters may not meet
class B performance.
UL Statement
UL listed: UL60950-1, 2nd Edition.
Canada
Industry Canada
This device complies with Canadian RSS-210. Operation is subject to the
following conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may
cause undesired operation of this device.
Conformité à la règlementation canadienne
Cet appareil ISM est conforme à la norme CNR-210 du Canada.
Son fonctionnement est assujetti aux conditions suivantes :
1. Cet appareil ne doit pas causer de brouillage préjudiciable.
2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le
brouillage pouvant causer un fonctionnement indésirable.
c-UL Statement
C-UL listed: CSA C22.2 No.60950-1-03, 2nd Edition for I.T.E. product safety.
Europe
The CE marking on the product indicates that this device is in
conformity with all essential requirements of the 1999/5/EC R&TTE
Directive. In addition, complies to 2006/95/EC Low Voltage Directive,
when shipped with recommended power supply.
For CE-related inquiries, please contact:
Honeywell Imaging & Mobility Europe BV
International Inc.
Nijverheidsweg 9-13
5627 BT Eindhoven
The Netherlands
Honeywell shall not be liable for use of our product with equipment (i.e.,
power supplies, personal computers, etc.) that is not CE marked and does
not comply with the Low Voltage Directive. This equipment is intended for
use throughout the European Community and has been assessed to the
following standards:
EN 300 328
EN 301 489-1
EN 301 489-17
EN 60950-1
Waste Electrical and Electronic Equipment
Information
Honeywell complies with Directive 2002/96/EC OF THE EUROPEAN
PARLIAMENT AND OF THE COUNCIL on waste electrical and electronic
equipment (WEEE).
This product has required the extraction and use of natural resources for its
production. It may contain hazardous substances that could impact health
and the environment, if not properly disposed.
In order to avoid the dissemination of those substances in our environment
and to diminish the pressure on the natural resources, we encourage you to
use the appropriate take-back systems for product disposal. Those systems
will reuse or recycle most of the materials of the product you are disposing in
a sound way.
The crossed out wheeled bin symbol informs you that the product
should not be disposed of along with municipal waste and invites you to use
the appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse, and recycling systems,
please contact your local or regional waste administration.
You may also contact your supplier for more information on the
environmental performances of this product.
Germany
If your product is marked with the GS symbol, then the product has
been issued a GS certificate showing compliance to EN 60950-1,
Second Edition.
This device is not intended for use in direct field of view at visual
display workplaces. To avoid distracting reflections at visual display workplaces,
this device should not be placed in direct field of view.
Australia/NZ
C-Tick Statement
Conforms to AS/NZS 3548 EMC requirement.
Korea
If the following label is attached to your product, the product meets Korean
agency approval:
이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 사용하는 것
을 목적으로 하며 ,
모든 역에서 사용할 수 있습니다 .
This product is EMC B grade equipment, intended for residential use.
This equipment can be used in any area.
Brazil (3820i, 2020-5 Scanner and AP-010BT)
This product is approved by Anatel, according to the procedures regulated
by Resolution No. 242/2000 and meets the technical requirements applied.
Este produto está homologado pela ANATEL, de acordo com os
procedimentos regulamentados pela Resolução No. 242/2000 e atende aos
requisitos técnicos aplicados.
Para maiores informações, consulte o site da ANATEL – www.anatel.gov.br
Japan
Complies with Technical Regulations Conformity Certification of
Specified Radio equipment.
Mexico
Applicable if NOM logo is marked on product. Conforms
to NOM-019.
Comision Federal de Telecomunicaciones (radio aprobación)
International
Safety Precautions for Lithium Batteries
• Do not place batteries in fire or heat the batteries.
• Do not store batteries near fire or other high temperature locations.
• Do not store or carry batteries together with metal objects.
• Do not expose batteries to water or allow the batteries to get wet.
• Do not connect (short) the positive and negative terminals, of the
batteries, to each other with any metal object.
• Do not pierce, strike or step on batteries or subject batteries to strong
impacts or shocks.
Modelo: 2020-5
1881-11-7084
(01)07898927490119
" Este equipamento operaem caráter secundário, isto é, não tem
direito aproteção contrainterferênciaprejudicial, mesmo de estações
do mesmo tipo, e não pode causar interferênciaasistemas operando
em caráter primário."
Modelo: 3820i
1880-11-7084
(01)07898927490102
" Este equipamento operaem caráter secundário, isto é, não tem
direito aproteção contrainterferênciaprejudicial, mesmo de estações
do mesmo tipo, e não pode causar interferênciaasistemas operando
em caráter primário."
Modelo: AP-010BT
0921-11-6583
(01)07898927490089
" Este equipamento operaem caráter secundário, isto é, não tem
direito aproteção contrainterferênciaprejudicial, mesmo de estações
do mesmo tipo, e não pode causar interferênciaasistemas operando
em caráter primário."
• Do not disassemble or modify batteries.
Caution:
Danger of explosion if batteries are incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the recycle program for batteries
as directed by the governing agency for the country where the batteries
are to be discarded.
LED Safety Statement
Scanner LEDs have been tested and classified as “EXEMPT RISK GROUP”
to the standard: IEC 62471:2006.
Radio Technology
Class II
CB Scheme
Certified to CB Scheme IEC 60950-1, Second Edition.
Solids and Water Protection
The 3820 has a rating of IP41, immunity of foreign particles and dripping
water.
The 3820i has a rating of IP54, immunity of foreign particles and sprayed
water.
Patents
For patent information, please refer to www.honeywellaidc.com/patents.
Warning
To reduce the possibility of heat-related injuries, avoid touching
sections of the scanner that feel warm.
!
!
Required Safety Labels
Scanner
Compliance
Label locations
Item Number,
Serial Number
and Revision
Information
location
Base
Compliance
Label locations
Item Number,
Serial Number
and Revision
Information
location
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Lector de código de barras de Honeywell
Honeywell
Honeywell 4800i Manual de usuario
Honeywell
Honeywell MK9535-79A540 - MS9535 VoyagerBT - Wireless Portable Barcode... Manual de usuario
Honeywell
Honeywell QUANTUME IS3480 Manual de usuario
Honeywell
Honeywell XENON 1902 Manual de usuario
Honeywell
Honeywell 4850DR Manual de usuario
Honeywell
Honeywell MK7580-30B41-00 - Metrologic MS7580 Genesis Manual de usuario
Honeywell
Honeywell VOYAGER 1250G Manual de usuario
Honeywell
Honeywell 3800 Linear Series Manual de usuario
Honeywell
Honeywell 8670 Manual de usuario
Honeywell
Honeywell VOYAGER 1200G Manual de usuario
Honeywell
Honeywell 4600g Manual de usuario
Honeywell
Honeywell Xenon 1910 Manual de usuario
Honeywell
Honeywell XENON 1900 Manual de usuario
Honeywell
Honeywell SF61 Manual de usuario
Honeywell
Honeywell VOYAGER 1250G Manual de usuario
Honeywell
Honeywell Voyager 1602g Manual de usuario
Honeywell
Honeywell MS9520 Voyager Manual de usuario
Honeywell
Honeywell Voyager 9520 Manual de usuario
Honeywell
Honeywell VoyagerGS 9590 Series Manual de usuario
Honeywell
Honeywell Xenon XP 195 Series Manual de usuario
