Hobby King Typhoon -EP Manual de usuario

Specs:

Wing Span: 1250mm

Wing Area: 29.13 Sq dm

Length: 1106mm

Weight: 1350g w/o battery

Required:

otor: BL2820

Radio: 4 channels

4 * 9~12g servos

Battery: 3S~4S 11.1~14.8V 2200mAh ~ 2600mAh

ESC: 60A

Warning!

This item is not a toy. It has the potential to cause serious harm if mistreated. The user accepts all

responsibility in the assembly of this model. Always check the model to ensure it is free of damage and all

screws and control hardware is tight before each flight.

Wing Assembly

1) Wing control hardware and wing tube.

2) Cut covering at servo mounts.

3) Install aileron servo, secure with screws. Depending on your servo you may need short extension leads

to reach your receiver.

4) Check to make sure the pre-fitted “CA Style” hinges are centered on the centerline. Then glue the hinge

with thin CA glue. After the glue cures, flex the control surface a few times to make sure it moves freely.

5) Install aileron horn, secure with included screw.

6) Attach aileron control rod with supplied hardware. ake sure servo is centered and servo arm is installed

90 degrees to the control rod for best movement.

Tail Assembly

1) Tail control hardware, tailwheel, and elevator joiner.

2) Insert horizontal stabilizer to fuselage. Center it, then draw a line noting its position. Using a sharp hobby

knife remove the covering for vertical fin and horizontal stabilizer. Do not cut balsa underneath.

2a) The areas shown where covering was removed will provide a good wood to wood joint when gluing tail

parts to fuselage.

3) To install the elevator joiner, a small channel needs to be cut on each elevator half to accept the wire.

4) Drill a 2mm hole to install the elevator linkage rod. Try to keep the hole perpendicular to the hinge line

and centered on the control surface. When the elevator joiner is installed, it needs to keep both halves

even to prevent unwanted rolling tendencies.

5) Glue the elevator joiner wire to the elevator halves with thick CA glue or epoxy. Lay both halves flat on a

table while the glue cures.

6) Insert elevator to fuselage before installing horizontal stabilizer.

7) Insert stabilizer to fuselage, centering it on the area where the covering was previously removed. Glue

the stabilizer in place with thick CA or epoxy.

8) Glue hinges with thin CA glue. Flex control surface several times to check for proper movement.

9) Install elevator servo, secure with screws

10) Install elevator horn, secure with supplied screws and square backplate

11) Attach elevator control rod with supplied hardware

12) Glue the vertical fin with CA glue or epoxy

13) Bend the tail wheel steel wire after inserting it through the plastic bracket. There should be about 15mm

of wire after the bend. Cut off remainging wire.

14) Cut a small channel in the rudder to allow the tail wheel wire to sit even with the hinge line when

installed.

15) Drill a 2mm hole to accept the tail wheel wire. Drill it centered on the control surface so tail wheel is

straight, relative to the rudder.

16) Insert rudder and hinges to fuselage. Glue rudder hinges with thin CA glue. Flex several times to

ensure free movement of the control surface.

17) Glue tail wheel steel wire with thick CA or epoxy.

18) Install rudder servo, secure with screws

19) Feed rudder cables through the fuselage. Loop cable through threaded end, and secure with aluminum

crimp. Repeat for both sides. For best control, control cables should cross the fuselage. So, cable on right

side of servo, should exit left side of fuselage.

20) Install rudder horn, secure with screws and 2 nut.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Juguete de Hobby King

Hobby King

Hobby King Ezio 1500 EP Manual de usuario

Hobby King

Hobby King Libero Guía de inicio rápido

Hobby King

Hobby King YAK- EPP Manual de usuario

Hobby King

Hobby King MiG-15 Manual de usuario

Hobby King

Hobby King SU-35 FIGHTER Manual de usuario

Hobby King

Hobby King EXTRA260P Manual de usuario

Hobby King

Hobby King TRAINSTAR Manual de usuario

Hobby King

Hobby King Maestro-46 Manual de usuario

Hobby King

Hobby King WARGO YAK55 Manual de usuario

Hobby King

Hobby King SBACH-342 Thunderbol Manual de usuario

Hobby King

Hobby King SuperG Manual de usuario

Hobby King

Hobby King DragonFly EDF Manual de usuario

Hobby King

Hobby King FALCON TRAINER Manual de usuario

Hobby King

Hobby King T-46 Manual de programación

Hobby King

Hobby King B-17G Manual de usuario

Hobby King

Hobby King Delta Rocket 100 Manual de usuario

Hobby King

Hobby King Breeze Manual de usuario

Hobby King

Hobby King Raven 990 MINI DLG 2017 Manual de usuario

Hobby King

Hobby King RYAN-STA Manual de usuario

Hobby King

Hobby King Gulfstream G500 ARF Manual de usuario

Hobby King

Hobby King 12A BEC Manual de usuario

Hobby King

Hobby King wing wing z-84 Manual de usuario

Hobby King

Hobby King Aether 3700 EP Manual de usuario

Hobby King

Hobby King Mig-15 EDF Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario