Hitachi X200 Series Manual de instrucciones

Hitachi IES Co., Ltd.

Inverter MODBUS

RTU Driver

1 System Configuration.......................................................................................................3

2 External Device Selection................................................................................................6

3 Communication Settings..................................................................................................7

4 Setup Items....................................................................................................................19

5 Cable Diagrams .............................................................................................................23

6 Supported Devices.........................................................................................................41

7 Device Code and Address Code....................................................................................45

8 Error Messages..............................................................................................................47

Inverter MODBUS RTU Driver

GP-Pro EX Device/PLC Connection Manual 2

Introduction

This manual describes how to connect the Display and the External Device (target Inverter).

In this manual, the connection procedure is described in the sections identified below:

1System Configuration

This section lists the types of External

Devices and SIO that you can connect.

)"1 System Configuration" (page 3)

2External Device Selection

Select a model (series) of the External

Device and its connection method.

)"2 External Device Selection" (page 6)

3Communication Settings

This section shows setting examples for

communicating between the Display and

the External Device.

)"3 Communication Settings" (page 7)

4Setup Items

This section describes communication

setup items on the Display.

Set the Display’s communication settings

in GP Pro-EX or in offline mode.

)"4 Setup Items" (page 19)

5Cable Diagrams

This section shows cables and adapters

for connecting the Display and the

External Device.

)"5 Cable Diagrams" (page 23)

Operation

Inverter MODBUS RTU Driver

GP-Pro EX Device/PLC Connection Manual 3

1 System Configuration

The following table lists system configurations for connecting Hitachi IES Co., Ltd. External Devices and the

Display.

Connection Configuration

• 1:1 Connection

• 1:n Connection (when using either COM1 or COM2)

Series Inverter*1

*1 is not added as an option. differs depending on the option.

Link I/F SIO Type Setting Example Cable Diagram

X200 X200-F Serial port connector

on the inverter RS-422/485

(2 wire) "Setting Example 1"

(page 7) " Cable Diagram 1"

(page 23)

SJ700 SJ700-FFRS485 port on the

inverter RS-422/485

(2 wire) "Setting Example 2"

(page 9) " Cable Diagram 2"

(page 32)

SJ700-2 SJ700-FF2 RS485 port on the

inverter RS-422/485

(2 wire) "Setting Example 3"

(page 11) " Cable Diagram 2"

(page 32)

SJ200 SJ200-F Serial port connector

on the inverter RS-422/485

(2 wire) "Setting Example 4"

(page 13) " Cable Diagram 1"

(page 23)

L200 L200-F Serial port connector

on the inverter RS-422/485

(2 wire) "Setting Example 5"

(page 15) " Cable Diagram 1"

(page 23)

WJ200 WJ200-FControl terminal

block on the inverter RS-422/485

(2 wire) "Setting Example 6"

(page 17) " Cable Diagram 2"

(page 32)

Display External Device

Display

External Device External Device External Device

Maximum number of External Devices: 16

Inverter MODBUS RTU Driver

GP-Pro EX Device/PLC Connection Manual 4

IPC COM Port

When connecting IPC with an External Device, the COM port used depends on the series and SIO type. Please

refer to the IPC manual for details.

Usable port

DIP switch setting: RS-232C

Series Usable Port

RS-232C RS-422/485(4 wire) RS-422/485(2 wire)

PS-2000B COM1*1 , COM2,

COM3*1, COM4

*1 The RI/5V can be switched. Use the IPC’s switch to change if necessary.

PS-3450A, PS-3451A,

PS3000-BA, PS3001-BD COM1, COM2*1*2 COM2*1*2 COM2*1*2

PS-3650A, PS-3651A COM1*1 --

PS-3700A (Pentium®4-M)

PS-3710A COM1*1, COM2*1,

COM3*2 , COM4

*2 Set up the SIO type with the DIP switch. Please set up as follows according to SIO type to be used.

COM3*2 COM3*2

PS-3711A COM1*1, COM2*2 COM2*2 COM2*2

PL-3000B, PL-3600T,

PL-3600K, PL-3700T,

PL-3700K, PL-3900T

COM1*1*2, COM2*1,

COM3, COM4 COM1*1*2 COM1*1*2

DIP switch Setting Description

1OFF

*1 When using PS-3450A, PS-3451A, PS3000-BA and PS3001-BD, turn ON the set value.

Reserved (always OFF)

2OFF

SIO type: RS-232C

3OFF

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available

8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available

9OFF

RS (RTS) Auto control mode: Disabled

10 OFF

Inverter MODBUS RTU Driver

GP-Pro EX Device/PLC Connection Manual 5

DIP switch setting: RS-422/485 (4 wire)

DIP switch setting: RS-422/485 (2 wire)

DIP switch Setting Description

1 OFF Reserved (always OFF)

2ON

SIO type: RS-422/485

3ON

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 OFF Short-circuit of SDA (TXA) and RDA (RXA): Not available

8 OFF Short-circuit of SDB (TXB) and RDB (RXB): Not available

9OFF

RS (RTS) Auto control mode: Disabled

10 OFF

DIP switch Setting Description

1 OFF Reserved (always OFF)

2ON

SIO type: RS-422/485

3ON

4 OFF Output mode of SD (TXD) data: Always output

5 OFF Terminal resistance (220Ω) insertion to SD (TXD): None

6 OFF Terminal resistance (220Ω) insertion to RD (RXD): None

7 ON Short-circuit of SDA (TXA) and RDA (RXA): Available

8 ON Short-circuit of SDB (TXB) and RDB (RXB): Available

9ON

RS (RTS) Auto control mode: Enabled

10 ON

Inverter MODBUS RTU Driver

GP-Pro EX Device/PLC Connection Manual 6

2 External Device Selection

Select the External Device to be connected to the Display.

Setup Items Setup Description

Number of Devices/PLCs Use an integer from 1 to 4 to enter the number of Devices/PLCs to connect to the

Display.

Manufacturer Select the manufacturer of the External Device to be connected. Select "Hitachi IES

Co., Ltd.".

Series

Select a model (series) of the External Device to be connected and connection method.

Select "Inverter MODBUS RTU".

In System configuration, check to make sure the external device to which you are

connecting is supported in "Inverter MODBUS RTU".

)"1 System Configuration" (page 3)

Port Select the Display port to be connected to the External Device.

Use System Area Not available in this driver.

Inverter MODBUS RTU Driver

GP-Pro EX Device/PLC Connection Manual 7

3 Communication Settings

This section provides examples of communication settings recommended by Pro-face for the Display and the

External Device.

3.1 Setting Example 1

GP Pro-EX Settings

Communication Settings

To display the setup screen, from the [System Settings] workspace, select [Device/PLC].

Device Setting

To display the [Individual Device Settings] dialog box, select the external device and click [Settings] from

[Device-Specific Settings] in the [Device/PLC] window. To connect multiple External Devices, click from

[Device-Specific Settings] in the [Device/PLC] window to add another External Device.

Inverter MODBUS RTU Driver

GP-Pro EX Device/PLC Connection Manual 8

External Device Settings

For External Device communication settings, use the FUNC key, Up key, Down key, and STR key located in the

keypad of the External Device.

Refer to your External Device manual for details.

1Set OPE/485 switch to "485" position.

2Turn ON the External Device.

3Press FUNC key.

4Press and hold Down key to display [C---].

5Press FUNC key.

6Press Up key to display the setting function code.

7Press FUNC key.

8Press Up key or Down key to select the setting value.

9Press STR key.

10 Reboot the External Device.

Setting Value

Function Code Setting Value Setup Description

C070 03 Selection of OPE/ModBus

C071 06 Communication speed selection

C072 1. Node allocation

C074 00 Communication parity selection

C075 1 Communication stop bit selection

C076 02 Communication error select

C077 0.00 Communication error time-out

C078 0. Communication wait time

A001 03 Frequency source setting

A002 03 Run command source setting

Inverter MODBUS RTU Driver

GP-Pro EX Device/PLC Connection Manual 9

3.2 Setting Example 2

GP Pro-EX Settings

Communication Settings

To display the setup screen, from the [System Settings] workspace, select [Device/PLC].

Device Setting

To display the [Individual Device Settings] dialog box, select the external device and click [Settings] from

[Device-Specific Settings] in the [Device/PLC] window. To connect multiple External Devices, click from

[Device-Specific Settings] in the [Device/PLC] window to add another External Device.

Inverter MODBUS RTU Driver

GP-Pro EX Device/PLC Connection Manual 10

External Device Settings

For External Device communication settings, use the FUNC key, Up key, Down key, and STR key located in the

keypad of the External Device.

Refer to your External Device manual for details.

1Turn ON the External Device.

2Press FUNC key for 3 seconds or longer.

3Press FUNC key to display [d001].

4Press and hold Down key to display [C---].

5Press FUNC key.

6Press Up key to display the setting function code.

7Press FUNC key.

8Press Up key or Down key to select the setting value.

9Press STR key.

10 Reboot the External Device.

Setting Value

Function Code Setting Value Setup Description

C071 06 Communication speed selection

C072 1. Node allocation

C073 8 Communication data length selection

C074 00 Communication parity selection

C075 1 Communication stop bit selection

C076 02 Selection of operation after communication error

C077 0.00 Communication trip limit time setting

C078 0. Communication wait time

C079 01 Communication mode selection

A001 03 Frequency source setting

A002 03 Run command source setting

Otros manuales para X200 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Inversor de Hitachi

Hitachi

Hitachi L300P-110L Manual de usuario

Hitachi

Hitachi J300 Series Manual de usuario

Hitachi

Hitachi SJ100 Series Manual de usuario

Hitachi

Hitachi WJ200-004M Manual de usuario

Hitachi

Hitachi SJ300-EL Series Guía de configuración

Hitachi

Hitachi SJ700-4000HFU2 Manual de usuario

Hitachi

Hitachi L100 Series Manual de usuario

Hitachi

Hitachi WJ200 Series Software Manual de usuario

Hitachi

Hitachi SJ100 Series Manual de usuario

Hitachi

Hitachi SJ700-2 Series Manual de usuario

Hitachi

Hitachi L200 Series Instrucciones de instalación y funcionamiento

Hitachi

Hitachi SJ300 Series Manual de lista de piezas

Hitachi

Hitachi YUTAKI S COMBI Series Manual de usuario

Hitachi

Hitachi L300P Series Manual de usuario

Hitachi

Hitachi L300P Series Guía de configuración

Hitachi

Hitachi Vector Control with the SJ300 Inverter Instrucciones de instalación y funcionamiento

Hitachi

Hitachi SJ700 Series Software Manual de usuario

Hitachi

Hitachi J100U2 SERIES Manual de usuario

Hitachi

Hitachi SJ200 Series Manual de usuario

Hitachi

Hitachi J300 Series Manual de usuario

Hitachi

Hitachi SJ700 Series Software Manual de usuario

Hitachi

Hitachi L100-004HFE Manual de usuario

Hitachi

Hitachi J300 Series Manual de usuario

Hitachi

Hitachi J300 Series Manual de instrucciones

Manuales populares de Inversor de otras marcas

Fourgroup

Fourgroup Easy Manual de usuario

Velleman

Velleman PI300M Manual de usuario

Sungrow

Sungrow SG350HX-US Manual de usuario

WilTec

WilTec 61897 Manual de usuario

SMA

SMA SUNNY BOY STORAGE 2.5 Manual de usuario

Simplicity

Simplicity LANDLORD 316 Manual de usuario

Santak

Santak SMAX 3000 Manual de usuario

ATON

ATON RA.Store-3 Manual de usuario

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Manual de usuario

Tektronix

Tektronix CFG250 Manual de usuario

Champion

Champion 200989 Manual de usuario

Vanner

Vanner 20-500 Series Manual de usuario

GE GEP Manual de usuario

Astrel Group

Astrel Group Power Reducer Guía rápida

MULTIQUIP

MULTIQUIP GDP-5H Guía

GoWISE

GoWISE PS1007 Manual de usuario

Promate

Promate PM13500D ES Manual de usuario

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Manual de usuario