Hitachi EX1200-5D Manual de usuario
(Troubleshooting)
Manual No. : KM-18F-E
Vol. No. : TT18F-E-00
Technical Manual
Excavator
PRINTED IN SINGAPORE (YS) 2006.04
EX1200-
5
D
Excavator Technical Manual (Troubleshootiing)
EX1200-5D
Service Manual (Manual No. KM-18F-E) consists of the following three separate volumes;
Technical Manual (Operational Principle) : Vol. No. TO18F-E
Technical Manual (Troubleshooting) : Vol. No. TT18F-E
Workshop Manual : Vol. No. W18F-E
EX1200-5D TM/TR 4/20/06, 3:39 PM1
epcatalogs.com
epcatalogs.com
INTRODUCTION
IN-01
TO THE READER
• This manual is written for an experienced technician
to provide technical information needed to maintain
and repair this machine.
• Be sure to thoroughly read this manual for cor-
rect product information and service procedures.
• If you have any questions or comments, at if you
found any errors regarding the contents of this
manual, please contact using “Service Manual
Revision Request Form” at the end of this man-
ual.
(Note: Do not tear off the form. Copy it for us-
age.):
Publications Marketing & Product Support
Hitachi Construction Machinery Co. Ltd.
TEL: 81-29-832-7173
FAX: 81-29-831-1162
ADDITIONAL REFERENCES
• Please refer to the materials listed below in addition
to this manual.
• The Operator’s Manual
• The Parts Catalog
• Operation Manual of the Engine
• Parts Catalog of the Engine
• Hitachi Training Material
MANUAL COMPOSITION
• This manual consists of three portions: the Techni-
cal Manual (Operational Principle), the Technical
Manual (Troubleshooting) and the Workshop Man-
ual.
• Information included in the Technical Manual
(Operational Principle):
technical information needed for redelivery and
delivery, operation and activation of all devices
and systems.
• Information included in the Technical Manual
(Troubleshooting):
technical information needed for operational per-
formance tests, and troubleshooting procedures.
• Information included in the Workshop Manual:
technical information needed for maintenance
and repair of the machine, tools and devices
needed for maintenance and repair, maintenance
standards, and removal/installation and assem-
ble/disassemble procedures.
epcatalogs.com
INTRODUCTION
IN-02
PAGE NUMBER
• Each page has a number, located on the center
lower part of the page, and each number contains
the following information:
Example : T 1-3-5
SAFETY ALERT SYMBOL AND HEADLINE
NOTATIONS
In this manual, the following safety alert symbol and
signal words are used to alert the reader to the
potential for personal injury of machine damage.
This is the safety alert symbol. When you see this
symbol, be alert to the potential for personal injury.
Never fail to follow the safety instructions prescribed
along with the safety alert symbol.
The safety alert symbol is also used to draw attention
to component/part weights.
To avoid injury and damage, be sure to use appropri-
ate lifting techniques and equipment when lifting
heavy parts.
• CAUTION:
Indicated potentially hazardous situation which
could, if not avoided, result in personal injury or
death.
• IMPORTANT:
Indicates a situation which, if not conformed to the
instructions, could result in damage to the machine.
• NOTE:
Indicates supplementary technical information or
know-how.
Consecutive Page Number for Each Group
Group Number
Section Number
T: Technical Manual W: Workshop Manual
epcatalogs.com
INTRODUCTION
IN-03
UNITS USED
• SI Units (International System of Units) are used in
this manual.
MKSA system units and English units are also
indicated in parenthheses just behind SI units.
Example : 24.5 MPa (250 kgf/cm2, 3560 psi)
A table for conversion from SI units to other system
units is shown below for reference purposees.
Quantity To Convert
From Into Multiply By
MPa kgf/cm210.197Pressure
MPa psi 145.0
kW PS 1.360Power
kW HP 1.341
Temperature °C °F °C×1.8+32
km/h mph 0.6214Velocity
min-1 rpm 1.0
Flow rate L/min US gpm 0.2642
mL/rev cc/rev 1.0
Quantity To Convert
From Into Multiply By
mm in 0.03937Length
mm ft 0.003281
L US gal 0.2642
L US qt 1.057
Volume
m3yd31.308
Weight kg lb 2.205
N kgf 0.10197Force
N lbf 0.2248
N⋅m kgf⋅m 1.0197Torque
N⋅m lbf⋅ft 0.7375
epcatalogs.com
Tabla de contenidos
Otros manuales de Excavador de Hitachi
Hitachi
Hitachi ZX 870-5G Manual de instrucciones
Hitachi
Hitachi ZX 670LC-5B Manual de usuario
Hitachi
Hitachi ZAXIS 850-3 Manual de usuario
Hitachi
Hitachi EX1900-6 Manual de usuario
Hitachi
Hitachi Zaxis 200LC Manual de usuario
Hitachi
Hitachi ZX 38U-5A Manual de usuario
Hitachi
Hitachi ZAXIS 135US-5B Manual de usuario
Hitachi
Hitachi ZX 210W-3 Manual de instrucciones
Hitachi
Hitachi 160LC-3 Manual de usuario
Hitachi
Hitachi Zaxis 160LC Manual de instrucciones
Hitachi
Hitachi ZAXIS 210LC-5N Manual de usuario
Hitachi
Hitachi ZAXIS 330-3 Manual de instrucciones
Hitachi
Hitachi ZAXIS 470LCH-3 ZAXIS 500LC-3 Manual de instrucciones
Hitachi
Hitachi EX80-5 Manual de usuario
Hitachi
Hitachi ZX170W-5A Manual de instrucciones
Hitachi
Hitachi EX2600-7B Manual de instrucciones
Hitachi
Hitachi Zaxis 330 Manual de usuario
Hitachi
Hitachi ZX 470-6 Manual de instrucciones
Hitachi
Hitachi Zaxis 33U-5A Manual de usuario
Hitachi
Hitachi Zaxis 330 Manual de usuario
