Hitachi ZAXIS 330-3 Manual de instrucciones

PRINTED IN JAPAN (E) 2006, 02

ZAXIS330

-3

class HYDRAULIC EXCAVATOR WORKSHOP MANUAL

PART NO. W1V7-E-00

Workshop Manual

Service Manual consists of the following separate Part No;

Technical Manual (Operational Principle) : Vol. No.TO1V7-E

Technical Manual (Troubleshooting) : Vol. No.TT1V7-E

Workshop Manual : Vol. No.W1V7-E

URL:http://www.hitachi-c-m.com Hydraulic Excavator

330-3 class

330-3•330LC-3

350H-3•350LCH-3

350LCK-3

350LC-3•350LCN-3

WIV7-E-00 2006.2.20, 11:50Page 1 AdobePageMaker7.0J/PPC

epcatalogs.com

INTRODUCTION

IN-01

TO THE READER

• This manual is written for an experienced technician

to provide technical information needed to maintain

and repair this machine.

• Be sure to thoroughly read this manual for correct

product information and service procedures.

• If you have any questions or comments, at if you

found any errors regarding the contents of this

manual, please contact using “Service Manual

Revision Request Form” at the end of this manual.

(Note: Do not tear off the form. Copy it for us-

age.):

Publications Marketing & Product Support

Hitachi Construction Machinery Co. Ltd.

TEL: 81-29-832-7084

FAX: 81-29-831-1162

ADDITIONAL REFERENCES

• Please refer to the materials listed below in addition

to this manual.

• The Operator’s Manual

• The Parts Catalog

• The Engine Manual

• Parts Catalog of the Engine

• Hitachi Training Material

MANUAL COMPOSITION

• This manual consists of three portions: the Techni-

cal Manual (Operational Principle), the Technical

Manual (Troubleshooting) and the Workshop Man-

ual.

• Information included in the Technical Manual

(Operational Principle):

technical information needed for redelivery and

delivery, operation and activation of all devices

and systems.

• Information included in the Technical Manual

(Troubleshooting):

technical information needed for operational per-

formance tests, and troubleshooting procedures.

• Information included in the Workshop Manual:

technical information needed for maintenance

and repair of the machine, tools and devices

needed for maintenance and repair, maintenance

standards, and removal/installation and assem-

ble/disassemble procedures.

PAGE NUMBER

• Each page has a number, located on the center

lower part of the page, and each number contains

the following information:

Example : T 1-3-5

Consecutive Page Number for Each Group

Group Number

Section Number

T: Technical Manual W: Workshop Manual

epcatalogs.com

INTRODUCTION

IN-02

SAFETY ALERT SYMBOL AND HEADLINE

NOTATIONS

In this manual, the following safety alert symbol and

signal words are used to alert the reader to the

potential for personal injury of machine damage.

This is the safety alert symbol. When you see this

symbol, be alert to the potential for personal injury.

Never fail to follow the safety instructions prescribed

along with the safety alert symbol.

The safety alert symbol is also used to draw attention

to component/part weights.

To avoid injury and damage, be sure to use appropri-

ate lifting techniques and equipment when lifting heavy

parts.

• CAUTION:

Indicated potentially hazardous situation which could,

if not avoided, result in personal injury or death.

• IMPORTANT:

Indicates a situation which, if not conformed to the

instructions, could result in damage to the machine.

• NOTE:

Indicates supplementary technical information or

know-how.

UNITS USED

• SI Units (International System of Units) are used in

this manual.

MKSA system units and English units are also

indicated in parenthheses just behind SI units.

Example : 24.5 MPa (250 kgf/cm2, 3560 psi)

A table for conversion from SI units to other system

units is shown below for reference purposees.

Quantity To Convert

From Into Multiply By

MPa kgf/cm210.197Pressure

MPa psi 145.0

kW PS 1.360Power

kW HP 1.341

Temperature °C °F °C×1.8+32

km/h mph 0.6214Velocity

min-1 rpm 1.0

Flow rate L/min US gpm 0.2642

mL/rev cc/rev 1.0

Quantity To Convert

From Into Multiply By

mm in 0.03937Length

mm ft 0.003281

L US gal 0.2642

L US qt 1.057

Volume

m3yd31.308

Weight kg lb 2.205

N kgf 0.10197Force

N lbf 0.2248

N⋅m kgf⋅m 1.0197Torque

N⋅m lbf⋅ft 0.7375

epcatalogs.com

SAFETY

SA-1

RECOGNIZE SAFETY INFORMATION

• These are the SAFETY ALERT SYMBOLS.

• When you see these symbols on your machine or

in this manual, be alert to the potential for per-

sonal injury.

• Follow recommended precautions and safe oper-

ating practices.

001-E01A-0001

SA-688

UNDERSTAND SIGNAL WORDS

• On machine safety signs, signal words designating

the degree or level of hazard - DANGER, WARNING,

or CAUTION - are used with the safety alert symbol.

• DANGER indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

• WARNING indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury.

• CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

• DANGER or WARNING safety signs are located

near specific hazards. General precautions are

listed on CAUTION safety signs.

• Some safety signs don't use any of the desig-

nated signal words above after the safety alert

symbol are occasionally used on this machine.

• To avoid confusing machine protection with personal

safety messages, a signal word IMPORTANT indi-

cates a situation which, if not avoided, could result in

damage to the machine.

• NOTE indicates an additional explanation for an

element of information.

002-E01A-1223

SA-1223

epcatalogs.com

Buy now

Hitachi Hydraulic Excavator Zaxis 330-3 class Workshop Manual PDF

With Instant Download

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Excavador de Hitachi

Hitachi

Hitachi Zaxis 200 Manual de instrucciones

Hitachi

Hitachi EX27U Manual de usuario

Hitachi

Hitachi ZAXIS 17U-2 Manual de usuario

Hitachi

Hitachi ZX 470LC-5A Manual de instrucciones

Hitachi

Hitachi ZX 670LC-5A Manual de instrucciones

Hitachi

Hitachi EX550-5 Manual de instrucciones

Hitachi

Hitachi ZAXIS 27U-2 Manual de usuario

Hitachi

Hitachi ZAXIS 470LC-5B Manual de usuario

Hitachi

Hitachi ZAXIS 200-3 class Manual de usuario

Hitachi

Hitachi ZAXIS 850-3 Manual de instrucciones

Hitachi

Hitachi ZX 170W-3 Manual de instrucciones

Hitachi

Hitachi ZX 40U-3 class Manual de usuario

Hitachi

Hitachi ZAXIS 135US-5B Manual de usuario

Hitachi

Hitachi ZX 29U-3 Manual de usuario

Hitachi

Hitachi EX 8000-6 Manual de instrucciones

Hitachi

Hitachi ZX 870-5G Manual de instrucciones

Hitachi

Hitachi ZAXIS 650LC-3 Manual de instrucciones

Hitachi

Hitachi ZAXIS 210LC-5N Manual de usuario

Hitachi

Hitachi ZX 470-5B Manual de instrucciones

Hitachi

Hitachi EX1900-6 Manual de usuario

Hitachi

Hitachi EX2600-7B Manual de instrucciones

Hitachi

Hitachi ZAXIS 170W-3 Manual de usuario

Hitachi

Hitachi ZAXIS 135US-6 class Manual de usuario

Hitachi

Hitachi ZAXIS 135US-3 class Manual de usuario

Manuales populares de Excavador de otras marcas

Hyundai

Hyundai Robex 210LC-9 Manual de usuario

sennebogen

sennebogen 830 E Manual de usuario

Topcon

Topcon X-63 Manual de uso y cuidado

jcb

jcb 15c-1 Manual de usuario

Case

Case CX290B Manual de usuario

SUNWARD

SUNWARD SWE155F Manual

CNH

CNH CX16B Manual de usuario

Super Products

Super Products MUD DOG 700 Manual de usuario

Komatsu

Komatsu ecot3 WA200-6 Guía de instalación

New Holland

New Holland E57C Manual de usuario

Hyundai

Hyundai Robex 160LC-9 Manual de usuario

Doosan

Doosan DX180LC Guía de instalación

Hyundai

Hyundai HW65AH Manual de usuario

mecalac

mecalac 14 MBX Manual de usuario

CASE CONSTRUCTION

CASE CONSTRUCTION CX350C Manual de usuario

Hyundai

Hyundai Robex 140LC-9 Manual de usuario

Case

Case CX50B Manual de usuario

Kobelco

Kobelco SK210LC-9 Guía de instalación