Hipo Technology HH JET Series Manual de usuario
Hipo INKJET plotter manual
0
HIPO
JET PLOTTER MANUAL
Hipo INKJET plotter manual
1
Words to Customers
Thank you for purchasing the Hipo plotter. It is our great honor to have
you as our customer. Upon your using of this product, please be sure to
read this manual carefully.
This manual is compiled to provide you with the system configuration,
installation steps, method of operation, and other information to ensure
the correct use of this product.
To timely receive our comprehensive after-sale services, please
contact:
Tel: 0086-10-82380636
Fax: 0086-10-82490122
E-mail: [email protected]
Declare
HipoJET plotter has registered in the Chinese Patent Office and
Trademark Office.
The trademark and trade name used in this manual belong to Beijing
Hipo Technology Co., Ltd and are protected by Chinese laws and
international treaties.
Hipo INKJET plotter manual
2
Contents
Chapter 1 Introduction ........................................................................................................... 3
Chapter 2 Preparation before installation ............................................................................. 4
（1）computer system requirements .................................................................................. 4
（2）Software output formats .............................................................................................. 4
（3）power requirements ..................................................................................................... 4
Chapter 3 Quick installation ................................................................................................... 5
Chapter 4 Installation of USB driver ....................................................................................... 7
Chapter 5 Plotting Center ..................................................................................................... 11
Chapter 6 Plotter Operation Panel ....................................................................................... 26
Chapter 7 Application ........................................................................................................... 27
Chapter 8 Notes.................................................................................................................... 29
Hipo INKJET plotter manual
3
Chapter 1 Introduction
Welcome to our HH JET series plotter. This plotter incorporates world fist-class
technology, generating stable performance, with elegant printing graphics and
comparatively high accuracy. It is very cost-effective and enjoys simplicity of
operation, with advanced automatic paper collecting and discharging functions.
HH JET is favored by the industry, especially for plotting large-breadth
Engineering Line Graphs, Garment Layout Maps, Oil Logging Maps,
Geological Survey Maps, Land Capability Map, and so on.
Our goal is to generate efficient output, save the cost of labor and production,
ultimately enhancing your competitiveness in the industry.
HHJET plotter Front View
Hipo INKJET plotter manual
4
Chapter 2 Preparation before installation
（1）computer system requirements
1、 Microsoft Windows 2000/xp
2、 Processor: Pentium 166M or above
3、 Memory: 512M or above
4、 Hard disk: 1G or above
5、 Driver: 4x or above
6、 USB2.0
（2）Software output formats
The Printout Administrative Center of HHJET only recognizes documents of
the following formats: *.plt、*. hpg、*.hpgl、*.dmpl、*.dxf, thus require
application software capable of generating the above formats, for instance,
AutoCAD and Apparel CAD. Or, you can also transfer documents of these
formats to the plotter.
（3）power requirements
1. Provide AC Power of 220V/50Hz（in some areas 110V/60Hz）in
accordance with the requirements of the plotter，with voltage fluctuation under
10%.
2. Reliable ground wire is a must。
3. Power line should be three-core or above
cables (one of them is groundwire) whether in
American or European Plug Boxes.
Hipo INKJET plotter manual
5
Chapter 3 Quick installation
（1） Installation Diagram
（2） Installation Steps
（a）Dismantle the packing box
1) Check the parts according to the packing list
2) Read the manual carefully
（b） Assemble the foot bars and upright posts according to the
Installation Diagram. The left and right upright posts and foot bars should
be paralleled. Do not screw down the two screws at the top of the left and
right upright posts yet; Screw them a little, not so tight, to assist the
installation of the handpiece.
（c） Add the draw rod according to the diagram. Remember not to
screw so tight of the screws on both ends of the draw rod temporarily, so
as to adjust the parallelism between the posts if needed and assist the
installation of the handpiece.
（d）Add the handpiece. It takes two people to put the handpiece
horizontally on the outer convex bolt of the upright posts, and tighten the
screws. Make sure to tighten the other screws with the precondition that
the left and right upright posts are paralleled.
（e） Add paper-collecting axle.
（f） Add paper-feeding axle and paper scroll.
（g） Add the paper-collecting balance pole and put it on its frame.
（h）Add the Nozzle. Be careful not to damage the touch spot of the
nozzle. Do not crash the nozzle against hard wall of the ink car to avoid
damage on the nozzle. Make sure that the nozzle is properly installed.
See:
Hipo INKJET plotter manual
6
Wrong plugging Correct plugging
（i） Connect the Three-core cable between the handpiece and the
draw rod. Make sure that the plug matches the socket, and screw down
the plug body.
（g） Connect the USB Interface cable.
The computer should be turned off when connecting USB cable. One
end of the cable is connected to the USB port of the computer and the
other to the USB port of the plotter. Make sure to fix it in the clip.
（k） Connect the power cord.
When the power is switched to “O”, connect one end of the power
cord with the plotter, and the other end to the power patch board which
has reliable protective groundwire.
Attention: please make sure that the line voltage is consistent to
the Voltage parameter labeled on the plotter.
Hipo INKJET plotter manual
7
Chapter 4 Installation of USB driver
1. copy to your computer，better under C drive.
2. double click , Interface appears as follows:
3. click ‘INSTALL’ and wait until the end of installation with the following
interface, and click ‘OK’ to finish installation.
4. plug the USB port cable of the plotter，and turn on the power of it,there will
be prompt of finding new hardware,（CH372/CH375） with the following
interface, and the installation automatically starts.
Hipo INKJET plotter manual
8
5. click “next”
6.click‘next, there will be the following installation process:
7. Automatic installation is done, with the following interface:
Hipo INKJET plotter manual
9
8. Finally, there will be a prompt in the desktop tray:
9. If the operating system is Windows2000，there will the following interface
when pressing “reset” on the plotter panel or plucking the USB plug, which is
quite normal. Just click “ok”.
10. Better equip the computer with USB2.0 protocol to ensure fast data
transmission bauds.
11. If the CH372/CH375 drive is successfully installed, plug in the USB port
cable of the plotter, and switch it on. With the following steps you will find
the device, click the right mouse button on “My Computer”.
Select “properties”
Tabla de contenidos
