HIK VISION 0300P Series Manual de usuario

100 Mbps PoE Switch

Quick Start Guide

UD29448B-A

Preface

Applicable Models

This manual is applicable to 0300P series 100 Mbps PoE switches.

Symbol Conventions

The symbols that may be found in this document are defined as

follows.

Symbol Description

Provides additional information to emphasize

or supplement important points of the main

text.

Indicates a potentially hazardous situation,

which if not avoided, could result in

equipment damage, data loss, performance

degradation, or unexpected results.

Indicates a hazard with a high level of risk,

which if not avoided, will result in death or

serious injury.

1 Introduction

1.1 Product Introduction

0300P series 100 Mbps PoE switches are layer 2 PoE switches,

providing advanced PoE power supply technology on the basis of

high-performance access. The devices support up to 300 m long-

range transmission (EXTEND mode), and feature high-priority ports

to ensure preferential network transmission in key service areas of

users. The devices also support port isolation to guarantee

information security, and can enable PoE watchdog to

automatically detect and restart ports. The devices are reliable,

easy to install and maintain, and equipped with rapid switching

functions. With multiple access ports, the devices are suitable for

small-scale LAN device access.

1.2 Packing List

Accessory Quantity

Switch × 1

Power Cord × 1

L-Shaped Bracket × 2

Screw

Without Indicator Panel × 4

With Indicator Panel × 6

Quick Start Guide × 1

Multilingual Information of

Network Switch × 1

1.3 Appearance

Device appearances vary with different models. The actual device

prevails.

Front Panel

0318P series switches (without indicator panels) feature sixteen

10/100 Mbps PoE RJ45 ports, one gigabit RJ45 port, and one gigabit

combo port.

0318P Series (Without Indicator Panels)

0318P series switches (with indicator panels) feature sixteen

10/100 Mbps PoE RJ45 ports and two gigabit combo ports.

0318P Series (with Indicator Panels）

0326P series switches (without indicator panels) feature twenty-

four 10/100 Mbps PoE RJ45 ports, one gigabit RJ45 port, and one

gigabit combo port.

0326P series switches (with indicator panels) feature twenty-four

10/100 Mbps PoE RJ45 ports and two gigabit combo ports.

Note

● The front panels of 0326P series switches (without indicator

panels) are similar to those of 0318P series switches (without

indicator panels). The only difference is that 0326P series

switches feature twenty-four 10/100 Mbps PoE RJ45 ports.

● The front panels of 0326P series switches (with indicator panels)

are similar to those of 0318P series switches (with indicator

panels). The only difference is that 0326P series switches feature

twenty-four 10/100 Mbps PoE RJ45 ports, twenty-four port

status indicators, and twenty-four PoE status indicators.

Port/Indicator Description of Front Panel

No.

Indicator/Port Description

1 PWR Indicator



Solid on: The switch is

powered on normally.



Unlit: No power supply is

connected or power supply

is abnormal.

2 PoE-MAX Indicator



Solid on: The output power

of the switch is about to

reach or has reached the

upper limit. The power

supply may be abnormal if

more devices are

connected.



Unlit: The switch does not

supply power to a powered

device (PD), or the switch

supplies power to a PD

normally and the output

power of the switch does

not reach the upper limit.

Note

The PoE-MAX indicator will be

unlit in five seconds after the

output power of the switch

reaches the upper limit.

Gigabit RJ45 Port

Indicator (when

gigabit RJ45 port G1

is connected)



Solid on: The port is

connected.



Flashing: The port is

transmitting data.



Unlit: The port is

disconnected or connection

is abnormal.

Gigabit SFP Fiber

Optical Port

Indicator (when

gigabit SFP fiber

optical port G1-F is

connected)



Solid on: The gigabit SFP

fiber optical port is

connected.



Flashing: The gigabit SFP

fiber optical port is

transmitting data.



Unlit: The gigabit SFP fiber

optical port is disconnected

or connection is abnormal.

Gigabit RJ45 Port

Indicator (when the

devices feature

only one combo

port G1/G1-F or

when gigabit RJ45

port G2 is

connected)



Solid on: The port is

connected.



Flashing: The port is

transmitting data.



Unlit: The port is

disconnected or connection

is abnormal.

Gigabit SFP Fiber

Optical Port

Indicator (when

gigabit SFP fiber

optical port G2-F is

connected)



Solid on: The gigabit SFP

fiber optical port is

connected.



Flashing: The gigabit SFP

fiber optical port is

transmitting data.



Unlit: The gigabit SFP fiber

optical port is disconnected

or connection is abnormal.

LINK/ACT Indicator

(for switches

without indicator

panels)



Solid on: The port is

connected.



Flashing: The port is

transmitting data.



Unlit: The port is

disconnected or connection

is abnormal.

10/100 Mbps RJ45

Port Indicator (for

switches with

indicator panels)

PoE Indicator (for

switches without

indicator panels)



Solid on: The switch

supplies power to a PD

normally.



Unlit: The switch is

disconnected from a PD or

power supply is abnormal.

PoE Status Indicator

of 10/100 Mbps

RJ45 Port (for

switches with

indicator panels)

7 EXTEND DIP Switch

Enable or disable long-range

transmission (EXTEND mode).



When the DIP switch is set

to “ON”, the corresponding

ports support up to 300 m

network transmission with

a port rate of 10 Mbps.



When the DIP switch is set

to “OFF”, the corresponding

ports support up to 100 m

network transmission with

a port rate of 100 Mbps.

8 Isolation DIP Switch

Enable or disable port isolation.



When the DIP switch is set

to “ON”, port isolation is

enabled. Ports in the same

isolation group cannot

communicate with each

other. Data transmission via

each port is isolated to

enhance network security.

Note

● Ports 1 to 8 of 0318P and 0326P series switches are high-

priority ports used to prioritize network transmission in key

service areas.



When the DIP switch is

switched to “OFF”, port

isolation is disabled. Ports

can communicate with

each other.

9 PoE Watchdog DIP

Switch

Enable or disable PoE

watchdog.



When the DIP switch is set

to “ON”, PoE watchdog is

enabled to automatically

detect device connection

statuses of corresponding

ports and restart ports in

case of communication

failures.



When the DIP switch is set

to “OFF”, PoE watchdog is

disabled. Corresponding

ports are no longer

automatically detected and

restarted in case of

communication failures.

10 10/100 Mbps PoE

RJ45 Port

Used for connection to a PD via

a network cable.

11 Gigabit Combo Port

(G1/G1-F)

When connected to a network

cable, the combo port is a RJ45

port. When plugged into with

an optical module and

connected to an optical fiber,

the combo port functions as a

fiber optical port.

Note



A combo port consists of a

RJ45 port and a fiber optical

port. You can use either the

RJ45 port or the fiber

optical port of a combo

port, but cannot use them

at the same time. For

example, if RJ45 port G1 is

connected, fiber optical

port G1-F is unavailable.



When connected to both a

network cable and an

optical fiber, the combo

port works as a fiber optical

port.

Gigabit Combo Port

(G2/G2-F)

Gigabit RJ45 Port

(G2) (when the

devices feature

only one combo

port G1/G1-F)

Used for connection to another

device via a network cable.

● Ports supporting long-range transmission vary with device

models. Ports 9 to 16 of 0318P series switches and ports 17 to

24 of 0326P series switches support up to 300 m network

transmission.

● Ports supporting port isolation vary with device models. Ports

1 to 16 of 0318P series switches and ports 1 to 24 of 0326P

series switches support port isolation.

● Ports supporting PoE watchdog vary with device models. Ports

1 to 16 of 0318P series switches and ports 1 to 24 of 0326P

series switches support PoE watchdog.

Rear Panel

0318P/0326P Series (Without Indicator Panels)

0318P/0326P Series (with Indicator Panels)

Port/Indicator Description of Rear Panel

No.

Indicator/Port Description

1 Grounding

Terminal

Used for connecting to the

grounding cable to protect the

switch from lightning.

2 Power Supply Use the attached power cord to

connect the switch to a socket.

2 Installation

Please select the appropriate installation method according to the

actual needs.

Note

If screws are not provided in the package, prepare them yourself.

Before You Start



Ensure that the desktop, wall, rack, or rail is stable and firm

enough.



Keep the room well-ventilated. Leave at least 10 cm of heat

dissipation space around the device.



Keep at least 1.5 cm vertical distance between two adjacent

devices for rack-mounted installation.

2.1 Desktop Installation

Place the device on the desk.

2.2 Wall-Mounted Installation

Steps

1. Check the distance between the two hanging holes on the rear

cover of the device.

2. Insert two M4 screws into the wall.

Note

●

Ensure that the distance between the two screws equals to the

distance between the two hanging holes.

●

Set aside at least 4 mm of the screw bodies outside the wall.

3. Align the hanging holes with the screws, and hang the device on

the screws.

Wall-Mounted Installation

2.3 Rack-Mounted Installation

Steps

1. Check the grounding and stability of the rack.

2. Use screws to fix the two L-shaped brackets to both sides of the

device.

Fix L-Shaped Brackets

3. Place your device against the rack, and fix the brackets to the

rack with screws to stably install your device.

Fix Brackets to Rack

3 Grounding

3.1 Connect Grounding Cable

Grounding is used to quickly release overvoltage and overcurrent

induced by lightening on the device, and to protect personal safety.

Select an appropriate grounding method according to the

installation conditions.

Note

The grounding terminal is on the rear panel or side panel of the

device. The actual device prevails.

3.1.1 With Grounding Bar

If a grounding bar is available at the installation site, follow the

steps below.

Steps

1. Connect one end of the grounding cable to the binding post on

the grounding bar.

2. Connect the other end of the grounding cable to the grounding

terminal of the device and tighten the screw.

Grounding with Grounding Bar

3.1.2 Without Grounding Bar

If there is no grounding bar but the earth is nearby and the

grounding body is allowed to be buried, follow the steps below.

Steps

1. Bury an angle steel or steel pipe (≥ 0.5 m) into the earth.

2. Weld one end of the grounding cable to the angle steel or steel

pipe and embalm the welding point via electroplating or coating.

3. Connect the other end of the grounding cable to the grounding

terminal.

Grounding with Angle Steel

3.2 Connect RJ45 Port

Use a network cable to connect the device to the RJ45 port of a

peer device such as network camera, NVR, switch, etc.

RJ45 Port Connection

3.3 Connect SFP Optical Module

Connecting an SFP optical module is supported when the device

has a fiber optical port or a combo port.

Steps

Caution

●

Single-Mode optical module needs to be paired for use.

●

Do not bend an optical fiber (curvature radius ≥ 10 cm) overly.

●

Do not look directly at an optical fiber connector because the

laser generated is harmful to eyes.

1. Connect the two paired SFP optical modules with an optical fiber.

2. Hold the SFP optical module from one side, and smoothly plug it

into the device along the SFP port slot until the optical module

and the device are closely attached.

3. After powering on the device, check the status of the optical port

indicator.

- If the indicator is lit, the link is connected.

- If the indicator is unlit, the link is disconnected.

4. Check the line, and make sure that the peer device has been

enabled.

4 Device Powering-On

Please use the attached power adapter or power cord to power on

the device.

Before powering on your device, make sure that:

• The operating power supply is compliant with rated input

standard.

• Port cables and grounding cables are correctly connected.

• If there is outdoor cabling, connect a lightning rod and a

lightening arrester to the cable.

Caution

Power supply lines and strong current wires cannot be wired

together, otherwise PDs or switch ports will be burnt.

Tabla de contenidos

Otros manuales de Cambiar de HIK VISION

HIK VISION

HIK VISION DS-3E2300P Series Manual de usuario

HIK VISION

HIK VISION DS-3E1 P Series Manual de usuario

HIK VISION

HIK VISION DS-3E0516 Series Manual de usuario

HIK VISION

HIK VISION DS-3D2216P Instrucciones de montaje

HIK VISION

HIK VISION DS-3E0108P-E Manual de usuario

HIK VISION

HIK VISION DS-3E2528B Manual de usuario

HIK VISION

HIK VISION DS-3E13XXP-SI Series Manual de usuario

HIK VISION

HIK VISION DS-3E1106HP-EI Manual de usuario

HIK VISION

HIK VISION DS-3E05 Series Manual de usuario

HIK VISION

HIK VISION DS-3E0106P-E/M Series Manual de usuario

HIK VISION

HIK VISION DS-3E0318P-E Manual de usuario

HIK VISION

HIK VISION DS-3E0524-E Manual de usuario

HIK VISION

HIK VISION DS-3E2300P-H Series Manual de usuario

HIK VISION

HIK VISION DS-3E1X05P Series Manual de usuario

HIK VISION

HIK VISION DS-3E0526P Series Manual de usuario

HIK VISION

HIK VISION DS-3E0509 Manual de usuario

HIK VISION

HIK VISION DS-3WF01C-2N Manual de usuario

HIK VISION

HIK VISION DS-3E0109P-E Manual de usuario

HIK VISION

HIK VISION 24 series Manual de usuario

HIK VISION

HIK VISION DS-3E2500-H Series Manual de operación y mantenimiento

HIK VISION

HIK VISION DS-3E15 P Series Manual de usuario

HIK VISION

HIK VISION DS-3E0318P-E/M Manual de usuario

HIK VISION

HIK VISION DS-3E1326P-EI Manual de usuario

HIK VISION

HIK VISION DS-3E1552P Series Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario