HIK VISION HWT-T120-P Manual de usuario

HD Turret and Bullet

Camera

User Manual

Thank you for purchasing our product. If there are any

questions, or requests, do not hesitate to contact the

dealer.

This manual applies to the models below:

Type

Model

Type I Camera

HWT-T120-P/HWT-T120

HWT-T140-P/HWT-T140

Type II Camera

HWT-T220-P

HWT-T240-P

Type III Camera

HWT-T120-M

HWT-T140-M

Type IV Camera

HWT-T220-M

HWT-T240-M

Type V Camera

HWT-B220-M/HWT-B220

HWT-B240-M/HWT-B240

Type VI Camera

HWT-B120-P/HWT-B120-M

HWT-B140-P/HWT-B140-M

This manual may contain several technical incorrect

places or printing errors, and the content is subject to

change without notice. The updates will be added to

the new version of this manual. We will readily improve

or update the products or procedures described in the

manual.

0100001080706

Regulatory Information

FCC Information

Please take attention that changes or modification not

expressly approved by the party responsible for

compliance could void the user’s authority to operate

the equipment.

FCC compliance: This equipment has been tested and

found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection

against harmful interference when the equipment is

operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

FCC Conditions

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received,

including interference that may cause undesired

operation.

EU Conformity Statement

This product and - if applicable - the

supplied accessories too are marked with

"CE" and comply therefore with the

applicable harmonized European

standards listed under the Low Voltage Directive

2014/35/EU, the EMC Directive 2014/30/EU.

2012/19/EU (WEEE directive): Products

marked with this symbol cannot be

disposed of as unsorted municipal waste in

the European Union. For proper recycling,

return this product to your local supplier

upon the purchase of equivalent new

equipment, or dispose of it at designated collection

points. For more information see: www.recyclethis.info.

2006/66/EC (battery directive): This product contains a

battery that cannot be disposed of as

unsorted municipal waste in the European

Union. See the product documentation for

specific battery information. The battery is

marked with this symbol, which may

include lettering to indicate cadmium (Cd), lead (Pb), or

mercury (Hg). For proper recycling, return the battery

to your supplier or to a designated collection point. For

more information see: www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)

standards requirements.

Safety Instruction

These instructions are intended to ensure that user can

use the product correctly to avoid danger or property

loss.

The precaution measure is divided into “Warnings” and

“Cautions”.

Warnings: Serious injury or death may occur if any of

the warnings are neglected.

Cautions: Injury or equipment damage may occur if any

of the cautions are neglected.

Warnings

In the use of the device, you must be in strict

compliance with the electrical safety regulations of

the nation and region.

Input voltage should meet both the SELV (Safety Extra

Low Voltage) and the Limited Power Source with 12

VDC according to the IEC60950-1 standard. Refer to

technical specifications for detailed information.

The output current of the power adapter must be no

more than 6A.

Do not connect multiple devices to one power

adapter to avoid over-heating or a fire hazard caused

by overload.

Make sure that the plug is firmly connected to the

power socket.

Make sure that the device is firmly fixed if wall

mounting or ceiling mounting is adopted.

If smoke, odor or noise rise from the device, turn off

the power at once and unplug the power cord, and

then contact the service center.

Never attempt to disassemble the camera by

unprofessional personal.

Cautions

Do not drop the camera or subject it to physical

shock.

Do not place the camera in extremely hot, cold (the

operating temperature shall be -40°C to 60°C), dusty

or damp locations, and do not expose it to high

electromagnetic radiation.

Do not touch senor modules with fingers.

If cleaning is necessary, use clean cloth with a bit of

ethanol and wipe it gently.

Do not aim the camera at the sun or extra bright

places.

The sensor may be burned out by a laser beam, so

when any laser equipment is in using, make sure that

the surface of sensor will not be exposed to the laser

beam.

Do not expose the device to high electromagnetic

radiation or extremely hot, cold, dusty or damp

environment.

Warnings Follow

these safeguards to

prevent serious injury

or death.

Cautions Follow these

precautions to prevent

potential injury or

material damage.

To avoid heat accumulation, good ventilation is

required for the operating environment.

Keep the camera away from liquid while in use for

non-water-proof device.

While in delivery, the camera shall be packed in its

original packing, or packing of the same texture.

Mark Description

Table 0-1 Mark Description

Mark

Description

DC Voltage

1Introduction

1.1 Product Features

The main features are as follows:

High performance CMOS sensor

IR cut filter with auto switch

OSD menu with configurable parameters

Auto white balance

Internal synchronization

SMART IR mode

3-axis adjustment

1.2 Overview

This manual applies to six types of cameras. The

overviews of each type are shown in the figures below.

1.2.1 Overview of Type I Camera

DC12VIN

Video Cable

Power Cord

12 VDC

Switch Button Mounting Base

Main Body

Enclosure

Figure 1-1 Overview of Type I Camera

Note:

Press and hold the switch button for 5 seconds to

switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS.

1.2.2 Overview of Type II Camera

DC12VIN

Enclosure

Main Body

Mounting

Base Video Cable

Switch Button

Power Cord

12 VDC

Figure 1-2 Overview of Type II Camera

Note:

Press and hold the switch button for 5 seconds to

switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS.

1.2.3 Overview of Type III Camera

DC12VIN

Clip Plate

Mounting Base

Trim Ring

Enclosure

Main Body

Switch Button

Video Cable

Power Cord

12 VDC

Figure 1-3 Overview of Type III Camera

Note:

Press and hold the switch button for 5 seconds to

switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS.

1.2.4 Overview of Type IV Camera

DC12VIN

Mounting

Base

Enclosure

Trim Ring Main Body

Switch Button

Video Cable

Power Cord

12 VDC

Figure 1-4 Overview of Type IV Camera

Note:

Press and hold the switch button for 5 seconds to

switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS.

1.2.5 Overview of Type V Camera

Video Cable

Power Cord

12 VDC

Switch Button

Mounting Base

Main Body

Lens

Figure 1-5 Overview of Type V Camera

Note:

Press and hold the switch button for 5 seconds to

switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS.

1.2.6 Overview of Type VI Camera

DC12VIN

Mounting Base

Main Body

Lens

Switch Button

Power Cord

12 VDC

Video Cable

Figure 1-6 Overview of Type VI Camera

Note:

Press and hold the switch button for 5 seconds to

switch the video output. Four kinds of video outputs

are available: TVI, AHD, CVI, and CVBS.

2Installation

Before you start:

Make sure that the device in the package is in good

condition and all the assembly parts are included.

Make sure that all the related equipment is power-off

during the installation.

Check the specification of the products for the

installation environment.

Check whether the power supply is matched with

your power output to avoid the damage.

Make sure the wall is strong enough to withstand

three times the weight of the camera and the mount.

If the wall is cement, insert expansion bolts before

installing the camera. If the wall is wooden, use

self-tapping screws to secure the camera.

If the product does not function properly, contact

your dealer or the nearest service center. Do NOT

disassemble the camera for repair or maintenance by

yourself.

2.1 Installation of Type I and Type II Camera

Before you start:

Type I and type II cameras share the same installation,

and we take type I camera as the example to describe

the installation method.

Both wall mounting and ceiling mounting are suitable

for the camera. We take ceiling mounting as an example

in this section. You can take the steps of ceiling

mounting as a reference, when adopting wall mounting.

Steps:

1. Disassemble the turret camera by rotating the

camera to align the notch to one of the marks, as

shown in the figure below.

Mark

Notch

Figure 2-1 Disassemble the Camera

2. Remove the mounting base from the camera body

with a flat object, e.g., a coin.

3. Paste the drill template (supplied) to the place

where you want to install the camera.

4. Drill the screw holes, and the cable hole (optional)

on the ceiling according to the drill template.

Screw

Hole

Cable

Hole

Side

Opening

Figure 2-2 Drill Template

Note:

Drill the cable hole, when adopting the ceiling outlet

to route the cable.

5. Attach the mounting base to the ceiling, and secure

them with supplied screws.

Type I Camera Type II Camera

Figure 2-3 Attach the Mounting Base to the Ceiling

Note:

The supplied screw package contains

self-tapping screws, and expansion bolts.

For cement ceiling, expansion bolts are required

to fix the camera. For wooden ceiling,

self-tapping screws are required.

6. Route the cables through the cable hole, or the side

opening.

7. Align the camera with the mounting base, and

tighten the screws to secure the camera on the

mounting base.

Figure 2-4 Secure the Camera with Mounting Base

8. Connect the corresponding cables, such as power

cord, and video cable.

9. Power on the camera to check whether the image

on the monitor is gotten from the optimum angle. If

not, adjust the camera according to the figure below

to get an optimum angle.

Pan Position

[0°to 360°]

Rotation Position

[0°to 360°]

Tilt Position

[0°to 75°]

Figure 2-5 3-axis Adjustment

1). Hold the camera body and rotate the enclosure

to adjust the pan position [0° to 360°].

2). Move the camera body up and down to adjust

the tilt position [0° to 75°].

3). Rotate the camera body to adjust the rotation

position [0° to 360°].

2.2 Installation of Type III Camera

Before you start:

Both wall mounting and ceiling mounting are suitable

for the camera. We take ceiling mounting as an example

in this section. You can take the steps of ceiling

mounting as a reference, when adopting wall mounting.

Steps:

1. Disassemble the turret camera.

1). Use the screw driver to loosen the screw on the

mounting base.

2). Align the notch to the clip plate to separate the

mounting base from the camera body.

Clip Plate

Notch

Figure 2-6 Disassemble the Camera

2. Paste the drill template (supplied) to the place

where you want to install the camera.

3. Drill the screw holes and the cable hole (optional)

on the ceiling according to the drill template.

Figure 2-7 Drill Template

Note:

Drill the cable hole, when adopting the ceiling outlet

to route the cable.

4. Attach the mounting base to the ceiling, and secure

them with supplied screws.

Figure 2-8 Attach the Mounting Base to the Ceiling

Note:

The supplied screw package contains

self-tapping screws, and expansion bolts.

For cement ceiling, expansion bolts are required

to fix the camera. For wooden ceiling,

self-tapping screws are required.

5. Route the cables through the cable hole, or the side

opening.

6. Combine the camera body with the mounting base.

1). Put the camera body in the mounting base.

2). Align the notch to the clip plate, and rotate the

enclosure a little bit.

3). Tighten the screw to secure the camera on the

mounting base.

Clip Plate

Figure 2-9 Secure the Camera with Mounting Base

7. Connect the corresponding cables, such as power

cord, and video cable.

8. Power on the camera to check whether the image

on the monitor is gotten from the optimum angle. If

not, adjust the camera according to the figure below

to get an optimum angle.

Pan Position

[0°to 360°]

Rotation Position

[0°to 360°]

Tilt Position

[0°to 75°]

Figure 2-10 3-axis Adjustment

1). Rotate the enclosure to adjust the pan position

[0° to 360°].

2). Move the camera body up and down to adjust

the tilt position [0° to 75°].

3). Rotate the camera body to adjust the rotation

position [0° to 360°].

2.3 Installation of Type IV Camera

Before you start:

Both wall mounting and ceiling mounting are suitable

for the camera. We take ceiling mounting as an example

in this section. You can take the steps of ceiling

mounting as a reference, when adopting wall mounting.

Steps:

1. Disassemble the turret camera by rotating the trim

ring anticlockwise to get the trim ring out of the

camera as shown in the figure below.

Figure 2-11 Get the Trim Ring out

2. Paste the drill template (supplied) to the place

where you want to install the camera.

Cable

Hole

Screw

Hole

Figure 2-12 Drill Template

Note:

Drill the cable hole, when adopting the ceiling outlet

to route the cable.

3. Attach the camera to the ceiling, and secure them

with supplied screws.

Figure 2-13 Attach the Camera to the Ceiling

Note:

The supplied screw package contains

self-tapping screws, and expansion bolts.

For cement ceiling, expansion bolts are required

to fix the camera. For wooden ceiling,

self-tapping screws are required.

4. Route the cables through the cable hole, or the side

opening.

5. Put the trim ring back, and tighten it by rotating it

clockwise.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de HIK VISION

HIK VISION

HIK VISION DS-2DF1-574D Manual de usuario

HIK VISION

HIK VISION DINOX DSR-3310 Manual de usuario

HIK VISION

HIK VISION DS-2CC102PN-IRA Manual de usuario

HIK VISION

HIK VISION DS-2AE4215T-D Manual de usuario

HIK VISION

HIK VISION HWI-D141H Manual de usuario

HIK VISION

HIK VISION DS-2CD6D54G1-IZS Manual de usuario

HIK VISION

HIK VISION DE4 Series Manual de usuario

HIK VISION

HIK VISION DS-2CD883F-E series Manual de usuario

HIK VISION

HIK VISION ECI-B64Z2 Manual de usuario

HIK VISION

HIK VISION DS-2CE16D8T-IT1 Manual de usuario

HIK VISION

HIK VISION DS-2XC6245G0-L Manual de usuario

HIK VISION

HIK VISION HWP-T4225I-D Manual de usuario

HIK VISION

HIK VISION DS-2CC51A5PN-VF Manual de usuario

HIK VISION

HIK VISION DS-2CE55C2P Manual de usuario

HIK VISION

HIK VISION ECI-D64Z2 Manual de usuario

HIK VISION

HIK VISION iDS-2VS435-F840-EY Manual de usuario

HIK VISION

HIK VISION DS-2CE10HFT-F28 Manual de usuario

HIK VISION

HIK VISION TURBO HD H1T Series Manual de usuario

HIK VISION

HIK VISION DS-2XT6645G0-LIZS/C15 Manual de usuario

HIK VISION

HIK VISION DS-2XC6142FWD-IS Manual de usuario

HIK VISION

HIK VISION IR Smart Speed Dome Manual de usuario

HIK VISION

HIK VISION DS-2CE19H8T-IT3ZF Manual de usuario

HIK VISION

HIK VISION CMHT1823 Manual de usuario

HIK VISION

HIK VISION DS-2CD6425G0 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario