HIK VISION DS-TCL400-E Manual de usuario

Smart On-Street ANPR Camera

Quick Start Guide

English

About this Manual

The Manual includes instructions for using and managing the Product.

Pictures, charts, images and all other information hereinafter are for

description and explanation only. The information contained in the Manual

is subject to change, without notice, due to firmware updates or other

reasons. Please find the latest version of this Manual at the Hikvision

website (https://www.hikvision.com/).

Please use this Manual with the guidance and assistance of professionals

trained in supporting the Product.

Trademarks

and other Hikvision’s trademarks and logos are the

properties of Hikvision in various jurisdictions.

Other trademarks and logos mentioned are the properties of their

respective owners.

Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL

AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND

FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”.

HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING

WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR

FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS

AT YOUR OWN RISK. IN NO EVENT WILL HIKVISION BE LIABLE TO YOU FOR

ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,

INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,

BUSINESS INTERRUPTION, OR LOSS OF DATA, CORRUPTION OF SYSTEMS, OR

LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT,

TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN

CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS.

YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR

INHERENT SECURITY RISKS, AND HIKVISION SHALL NOT TAKE ANY

RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR

OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK,

VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER,

HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.

English

YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE

LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE

CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE,

FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE

RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF

PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, OR DATA PROTECTION AND

OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY

PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION

OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR

PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN

THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR

FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE

APPLICABLE LAW, THE LATER PREVAILS.

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly approved

by the party responsible for compliance could void the user’s authority to

operate the equipment.

FCC compliance: This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own

expense.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference

that may cause undesired operation.

English

EU Conformity Statement

This product and - if applicable - the supplied accessories too

are marked with "CE" and comply therefore with the

applicable harmonized European standards listed under the

EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS

Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this

symbol cannot be disposed of as unsorted municipal waste in

the European Union. For proper recycling, return this product

to your local supplier upon the purchase of equivalent new

equipment, or dispose of it at designated collection points. For more

information see: www.recyclethis.info

2006/66/EC (battery directive): This product contains a

battery that cannot be disposed of as unsorted municipal

waste in the European Union. See the product

documentation for specific battery information. The battery

is marked with this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling,

return the battery to your supplier or to a designated collection point. For

more information see: www.recyclethis.info

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

이기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은

기기로서 가정용 환경에서 사용하는 경우 전파간섭의 우려가

있습니다.

Safety Instructions

This is a class A product and may cause radio interference in which case

the user may be required to take adequate measures.

Use of the product must be in strict compliance with the local laws and

regulations. Please shut down the device in prohibited area.

Use of the product must be in strict compliance with the local electrical

safety regulations.

Use the power adapter provided by qualified manufacturer. Refer to the

English

product specification for detailed power requirements.

It is recommended to provide independent power adapter for each device

as adapter overload may cause over-heating or a fire hazard.

Make sure that the power has been disconnected before you wire, install,

or disassemble the device in the authorized way according to the

description in the manual.

To avoid electric shock, DO NOT directly touch exposed contacts and

components once the device is powered up.

DO NOT use damaged power supply devices (e.g., cable, power adapter,

etc.) to avoid electric shock, fire hazard, and explosion.

DO NOT directly cut the power supply to shut down the device. Please

shut down the device normally and then unplug the power cord to avoid

data loss.

The socket-outlet shall be installed near the equipment and shall be easily

accessible.

Make sure the power supply has been disconnected if the power adapter

is idle.

Connect to earth before connecting to the power supply.

To avoid heat accumulation, good ventilation is required for a proper

operating environment.

Store the device in dry, well-ventilated, corrosive-gas-free, no direct

sunlight, and no heating source environment.

Avoid fire, water, and explosive environment when using the device.

Install the device in such a way that lightning strikes can be avoided.

Provide a surge suppressor at the inlet opening of the equipment under

special conditions such as the mountain top, iron tower, and forest.

Keep the device away from magnetic interference.

Avoid device installation on vibratory surfaces or places. Failure to comply

with this may cause device damage.

DO NOT touch the heat dissipation component to avoid burns.

DO NOT expose the device to extremely hot, cold, or humidity

environments. For temperature and humidity requirements, see device

specification.

No naked flame sources, such as lighted candles, should be placed on the

equipment.

English

DO NOT touch the sharp edges or corners.

To prevent possible hearing damage, DO NOT listen at high volume levels

for long periods.

If smoke, odor, or noise arises from the device, immediately turn off the

power, unplug the power cable, and contact the service center.

If the device cannot work properly, contact the store you purchased it or

the nearest service center. DO NOT disassemble or modify the device in

the unauthorized way (For the problems caused by unauthorized

modification or maintenance, the company shall not take any

responsibility).

Keep all packaging after unpacking them for future use. In case of any

failure occurred, you need to return the device to the factory with the

original packaging. Transportation without the original packaging may

result in damage to the device and the company shall not take any

responsibility.

Please enforce the protection for the personal information and the data

security as the device may be confronted with the network security

problems when it is connected to the Internet. Contact us if network

security risks occur.

Please understand that you have the responsibility to configure all the

passwords and other security settings about the device, and keep your

user name and password.

DO NOT touch the lens with fingers directly in case the acidic sweat of the

fingers erodes the surface coating of the lens.

DO NOT aim the lens at the strong light such as sun or incandescent lamp.

The strong light can cause fatal damage to the device.

DO NOT disconnect the power during formatting, uploading, and

downloading. Or files may be damaged.

English

Appearance

No.

Description

No.

Description

Status indicator

Supplement light

Camera

Column mount

Cable Overview

Interface

Description

Interface

Description

RS-485

interface

Network

interface

UART

debugging

interface

Power

input

Warning:

The network interfaces are dedicated non-standard PoE network

interfaces. You are not allowed to connect them to normal devices to

avoid burning the normal devices.

English

Connect Network Cable

Follow the No. on the figure below to connect the network interfaces of

the device to the switch via twisted pair.

Warning:

Incorrect cable order will burn the device and power supply.

1 3 4 5 6 7 8

No.

Color

No.

Color

Light orange

Light blue

Orange

Green

Light green

Light brown

Blue

Brown

Hand-in-Hand Cascade

Connect the devices in hand-in-hand cascade mode to the switch and

power supply via combiner patch cord. 2-channel cascade is supported in

the environment of 100 M network and 48 VDC power supply. Up to 8

single-lens devices and 6 dual-lens devices can be connected in cascade for

each channel.

Warning:

The PoE interface of the device does not comply with Limited Power

Source. The device which is provided power by the PoE interface shall be

equipped with a fire-retardant enclosure.

The cascade distance for devices is up to 100 m.

It is recommended to use 1000 M network for video transmission.

English

No.

Description

No.

Description

Switch

Combiner patch

cord

Power cord (48

VDC)

Network cable

Power Supply Mode

48 VDC

5 5

English

24 VDC

5 5

No.

Description

No.

Description

The distance between

two devices (L1)

Cabinet (48 VDC/24

VDC power supply +

100 M/1000 M switch

+ combiner cable)

The distance between

the device and

cabinet (L2)

Network cable (< 100

m, 220 VAC)

1000 M switch

Note:

The number of the cascaded devices of each channel depends on L1 and L2.

Debug Wiring

Tabla de contenidos

Otros manuales de Cámara de seguridad de HIK VISION

HIK VISION

HIK VISION DS-2CE11D0T-PIRLP Manual de usuario

HIK VISION

HIK VISION DS-2CE10HFT-F Manual de usuario

HIK VISION

HIK VISION DS-2TD2 Series Manual de usuario

HIK VISION

HIK VISION DS2DE2204IW Manual de usuario

HIK VISION

HIK VISION DS-2DE4225W-DE Manual de usuario

HIK VISION

HIK VISION PanoVu PT Series Manual de usuario

HIK VISION

HIK VISION DS-2CC11D3S-IR Manual de usuario

HIK VISION

HIK VISION E-series Manual de usuario

HIK VISION

HIK VISION DS-2CD3066G2-IS Manual de usuario

HIK VISION

HIK VISION DS-2CD3D26G2T-IZHSY Manual de usuario

HIK VISION

HIK VISION DS?2CD753F?E Manual de usuario

HIK VISION

HIK VISION DS-2AE714 Manual de usuario

HIK VISION

HIK VISION DS-2DP1636ZIX-D Manual de usuario

HIK VISION

HIK VISION DS-2CD2146G1-IS-4mm Manual de usuario

HIK VISION

HIK VISION DS-2CD3T86G2-4IS Manual de usuario

HIK VISION

HIK VISION DS-2CD883F-EW series Manual de usuario

HIK VISION

HIK VISION iDS-2CD8A46G0-IZHS Manual de usuario

HIK VISION

HIK VISION D8T Series Manual de usuario

HIK VISION

HIK VISION DS-2TD6267-100C4L/WY Manual de usuario

HIK VISION

HIK VISION DS-2CC1282P(N)-IT3 Manual de usuario

HIK VISION

HIK VISION EZVIZ Mini Pano Manual de usuario

HIK VISION

HIK VISION ids-mcd202-b Manual de usuario

HIK VISION

HIK VISION iDS-2CD7A86G0-IZHSY Manual de usuario

HIK VISION

HIK VISION DS-MH2211/32G Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario