HIK VISION Pyronix Enforcer V10 Instrucciones de funcionamiento

Enforcer

Extended Programming Guide

Alarm Panel

Time 10:09 c

Version 01

2Enforcer V10 Programming Guide

Contents

Default Codes 4

Access Codes 4

Clean Start Codes 4

Other Codes 4

Technical Support 4

The Engineer Menu 5

Accessing The Engineer Menu 5

Exiting The Engineer Menu 5

Useful Menu Options 5

Wireless device control 5

General Information 6

Default Codes 6

Initial Power Up 6

Wired Keypads/Readers 6

Keypads 7

The Internal Tag Reader (EUR-107) 7

The External Tag Reader (EUR-108) 7

Text Programming 8

Engineer Function: Set System 8

Engineer Function: Forced Arm On Inputs

The Engineer Menu 9

Set Date & Time 9

Wireless Device Control 10

Learning Inputs 10

Learning Bells 11

Program Keyfob Buttons 12

Control Arming Stations 12

Change Inputs 13

Input Attributes 14

Change Inputs Programming 14

Choose Mode 15

Choose Mode Programming 15

Install ZEMs 16

Install ZEMS Programming 16

Change Outputs 16

Change Output Programming 17

Assign Keypads/Readers 17

Programming Keypads 19

Programming Readers 19

Wireless Arming Station Options 20

Change Timers 21

Change Timers Programming 21

Codes And Users 21

Change Duress Codes 22

Change Master Manager Code 22

Change Engineer Code 22

Change Codes Programming 22

Volume Control 22

Volume Control Programming 23

System Options 24

Site Options 24

Site Options Programming 26

System Displays 26

System Displays Programming 27

Exit Modes 27

Exit Modes Programming 27

Review Logs 28

Panel Log 28

Enforcer V10 Programming Guide

Access Log 28

Reviewing Logs 28

Engineer Tests 28

Walk Test Programming 30

Soak Control Programming 30

Test Siren, Battery Load Test and Outputs 30

Test Communications 31

Diagnostics 31

Wireless Devices 31

View Inputs 31

Signal Strength 31

Battery Status 32

Wireless Dual Frequency Menu 32

Wired Devices 32

View Inputs 32

View PSUs 32

Communications 33

Wireless Device Diagnostics 34

Wired Device Diagnostics 35

Communications Diagnostics 35

Engineer Reset Options 35

Engineer Reset Options Programming 36

Alarm Response 36

Alarm Responses Programming 37

Set Up Downloading 37

Set Up Downloading via Cloud 37

Connecting to the InSite software: 38

Set Up Downloading via RS232 38

Connecting to the InSite software: 38

Software Revision 39

Clean Start 39

Clean Start Programming 40

Appendix A. Defaults 41

Appendix B. Input Types 47

Appendix C. Timers 48

Appendix D. Output Types 50

Appendix E. Fault Finding 53

Wireless Fault Displays 53

RS-485 Bus Problems 54

Power Supply Problems 54

Detection Faults 55

Communication Faults 55

4Enforcer V10 Programming Guide

DEFAULT CODES

Access Codes

User Code: ‘Blank’

Master Manager Code: 2222.

Engineer: 1111

Clean Start Codes

Clean start with the code ‘2000’ (UNGRADED)

Clean start with the code ‘2020’ (Grade 2)

Other Codes

Keypad Security Code: ‘2000’

Delete All Wireless Data: ‘2000’

TECHNICAL SUPPORT

If you are still experiencing issues with the installation, please call our UK technical support team.

Please note: In order to get your issue resolved quickly, please have the software revision of the panel

ready to give to one of our engineers.

Alternatively if you do not require assistance straight away, you can email the team who will reply to you as soon

as possible.

Our oce hours are: Monday to Friday 8:00 - 18:30.

0333 444 1280

([email protected]

Enforcer V10 Programming Guide

THE ENGINEER MENU

The Engineer Menu must be accessed in order to program all system congurations.

Please note

1. All tamper alarms (including case tamper), will be disabled once in the Engineer Menu.

2. All personal attack and re alarms will not cause an alarm in the Engineer Menu.

Accessing The Engineer Menu

Access to the Engineer Menu will be allowed if the Enforcer is unset. If set, the Enforcer must be unset rst via a valid

user code/tag/keyfob in order to gain access. If the ‘Allow Engineer Menu’function in the Master Manager Menu is

set as ‘No’, the message ‘Authorisation Required’ will be shown and access will be denied until this option is set as

‘ Ye s ’.

1. Enter the engineer code (default 1111).

2. If any faults that are active, they will be displayed now on the screen. Press Aand enter the engineer

code again.

3. ‘SET DATE & TIME’is displayed.

4. Engineers Menu has been accessed.

When the Engineer Menu is accessed, a high pitch tone is generated intermittently.

Please note: It is essential that a factory default (clean start) is performed after initial power up to

ensure that the correct defaults have been chosen.

Exiting The Engineer Menu

When a Main Menu Item (a menu that is in capital letters) is displayed, press or scroll to‘EXIT ENGINEERS MENU?’

and press .

Useful Menu Options

Wireless device control

Learns and deletes all wireless inputs, bells and arming stations. To learn wireless keyfobs enter the Master Manager

menu and scroll to CHANGE CODES. (Refer to the user manual).

Change inputs

Programs all input types, attributes, areas and names and on the Enforcer.

Assign keypads and readers

Assigns wired/wireless keypads and readers, and enables readers for entry control.

Please note: Keypads and Readers must be addressed at the device and at the keypad.

6Enforcer V10 Programming Guide

Codes and users

Changes the ‘Engineer code’, ‘Master Manager code’ and ‘Duress codes’. To change user codes enter the Master

Manager menu and scroll to ‘EDIT USERS’.

Change outputs

Programs any outputs and assigns output modules to the Enforcer.

Diagnostics

Displays power, input status, wireless arming stations, wireless signal strength and wireless battery levels.

Communications

Enables a modem (if connected), allows signalling via communication formats or SMS, and enables the ProControl+

App and Cloud. Please refer to the ‘Communications Guide’.

GENERAL INFORMATION

Default Codes

User: ‘Blank’

Master Manager: 2222

Engineers: 1111

Initial Power Up

Power up the Enforcer system, an alarm will be generated. Proceed to the Enforcer keypad, which will display (from

power up):

1. Once power has been applied to the Enforcer, ‘Please Wait’ will be displayed, followed by ‘485 Comms Lost’.

After approximately one minute, the Enforcer will the time on the display, indicating the system is ready to

use.

2. The Enforcer is defaulted to keypad address ‘0’.

Testing The Keypad

With the system unset, press the key for 5 seconds at any keypad. This will cause all the LEDs on that keypad to

illuminate, and the LCD screen to display each pixel. The keypad will revert to normal display after the test which

will last about 10 seconds.

Wired Keypads/Readers

Enforcer V10 Programming Guide

Keypads

Three additional wired keypads may also be connected to the Enforcer.

Key functions

= Exit Engineer and Manager menu / Selects Area A.

= Moves backwards to the previous menu item / Selects Area B.

c= Enables chime and displays additional information in the log / Scrolls back‘one’ in a sub menu / Selects Area

D= Moves forward in the log / scrolls between options and enters the master manager menu /Selects Area D.

fp= Not used. []= Directional buttons.

I= Selects items and enters menus.

A= Cancels items, resets the panel and moves to next item in a menu item.

Please note

1. If any additional keypads are installed on the Enforcer, it is possible to access the Engineer Menu on

any keypad. For example, if the Engineer menu is accessed on keypad address 0, the other keypads

will display ‘System Busy’. To access the Engineer menu on any other keypad, press the key on the

relevant keypad and the Engineer menu will be displayed.

2. A wireless keypad can be connected to set/unset (LEDRKP-WE)

The Internal Tag Reader (EUR-107)

The Internal tag reader can be used for setting/unsetting, entry control or access control. Refer to the installation

manual for all connections.

Tag Area (Where a valid tag must be presented to set/unset)

Alert LED

Alarm LED

Tamper LED

Fault LED

Unset LED

The External Tag Reader (EUR-108)

The Internal Tag Reader can be used for setting/unsetting, entry control or access control. Refer to the installation

manual for all connections.

To set/unset the system using the External Tag Reader, present a pre-programmed tag to the

centre of the prox.

The prox will display the system status: Green = Unset. Red = Set. Present the tag again

within 10 seconds to set and unset the system.

Please note: The system will set depending on the type of exit mode programmed

(Final door, Timed or Push to set)

8Enforcer V10 Programming Guide

Text Programming

Text may be programmed for input names, for the ‘sign-on’ message, and to

identify the Level or Area. Each key is allocated alpha-numeric or punctuation

marks characters as shown left:

The Enforcer incorporates predictive text, so the system will predict which word

is being spelt. For example, if ‘B’ is entered, followed by ‘e’then ‘d’, Bedroom will

be displayed. To accept, press . If the word that is required doesn’t appear

on the LCD display, type in the next letter and so forth until complete.

To type a word, press the relevant key the appropriate number of times – e.g.

for the letter‘k’ press twice, or for the letter ‘s’ press four times.

For punctuation marks, press the key.

In addition, the keys are used as follows:

= make the character into a capital

= move cursor left

= clears cursor / adds a space

= moves cursor right

Engineer Function: Set System

Setting and unsetting the system can be done using the Engineer code.

1. Press .

2. Enter the Engineer code (default 1111).

3. Press if any faults appear.

4. ‘SET SYSTEM’ is displayed.

5. Press 

6. Select the areas to set. Press 

7. The setting period will begin.

8. Once the timer expires, and a beep is heard, the Enforcer is set.

9. To unset, enter the Engineer code again.

Engineer Function: Forced Arm On Inputs

The ‘Force Arm On Inputs’ function enables two nominated inputs on the Enforcer to be set. Either input can be

triggered to allow real life signalling or alarm testing. This function is useful when a building is full of people and

these tests are needed.

Please note

1. The system will give the correct signalling response to the Setting, and any resulting alarm.

2. If the system has been set by any other code, the Engineer code will not unset it.

Enforcer V10 Programming Guide

1. Press 

2. Enter the Engineer code (default 1111).

3. Press if any faults appear.

4. ‘SET SYSTEM’ is displayed.

5. Press 

6. ‘FORCE ARM ON 1st INPUT’ is displayed.

7. Enter the 1st input that is to be active. Press 

8. Enter the 2nd input that is to be active. Press 

9. Select the areas to set. Press 

10. The setting period will begin

11. Once the timer expires, and a beep is heard, the Enforcer is set and the 2

inputs chosen will be active.

12. To unset, enter the Engineer code again.

THE ENGINEER MENU

Any programming is only saved when exiting the Engineer menu. It is essential that a ‘CLEAN START’ is performed

after initial power up.

SET DATE & TIME

All log entries are date and time stamped. This can also programmed in the Master Manager Mode. The time is also

shown on the LCD in ‘Day Mode’.

Please note: Please note that powering down the system will reset the time and date information.

Year, Month, Day, Hours, and Minutes

Enter the year, month, day, hours and minutes.

DST Adjust

Enable or disable the ‘Day Light Saver Time Adjust’ as required.

Set Date and Time Programming

Press or to scroll to ‘SET DATE AND TIME’. Press .

‘Year’ will be displayed. Enter the year and press . Repeat for Month, Day, Hours

and Minutes and press .

‘DST Adjust’ will be displayed. Press [or ]to enable or disable the function

and press .

10 Enforcer V10 Programming Guide

WIRELESS DEVICE CONTROL

The Enforcer supports a maximum of 32 wireless inputs, 32 wireless keyfobs, 2 wireless Deltabell external sounders

and 4 wireless arming stations.

Please note: This is without any expanders tted to the system

Control Inputs

‘Control Inputs’learns and deletes wireless inputs (detectors, contacts, sensors etc).

Control Bells

‘Control Bells’ learns and deletes wireless Deltabell external sounders.

Programming Keyfob Buttons

‘Program Keyfob Buttons’assigns actions to each buttons on the keyfob.

[0] No action: Disables the button.

[2] Set Area: Sets the chosen area.

[4] Operate Output:Triggers an output (programmable)

when the nominated button is pressed.

[1] Show Status: GREEN = Unset. RED = Set.

[3] Unset Area: Unsets the chosen area.

[6] Personal attack: Activates a personal attack

activation (programmed in Engineers only)

Please note: Keyfobs are learnt in the Master Manager Menu in the function ‘EDIT USERS’.

Control Arming Stations

‘Control Arming Stations’ learns and deletes wireless arming stations. These are use to set/unset the system and

trigger outputs.

Learning Inputs

1. Press or to scroll to ‘WIRELESS DEVICE CONTROL’. Press 

2. ‘Control Inputs’will be displayed. Press .

3. ‘Learn Devices’will be displayed. Press or press to access the delete

menus (you can either delete individual devices or delete all).

4. Press [or ]to select the input (1-32) to learn and press .

5. Open the wireless device then press and hold the‘LEARN’button until all LEDs

ash then release.

Tabla de contenidos

Otros manuales de Panel de control de HIK VISION

HIK VISION

HIK VISION DS-19A Series Manual de usuario

HIK VISION

HIK VISION AX Series Manual de usuario

HIK VISION

HIK VISION DS-KH6310-W(L) Manual de usuario

HIK VISION

HIK VISION DS-PK00 series Manual de usuario

HIK VISION

HIK VISION DS-19A08-F/Kx Manual de usuario

HIK VISION

HIK VISION AXHub Manual de usuario

HIK VISION

HIK VISION AX Series Manual de usuario

HIK VISION

HIK VISION DS-19S08N-04F/K Series Manual de usuario

HIK VISION

HIK VISION DS-PK-LRT(433MHz) Manual de usuario

HIK VISION

HIK VISION DS-PWA96-M2-WB Manual de usuario

HIK VISION

HIK VISION AX Series Manual de usuario

HIK VISION

HIK VISION AX HYBRID PRO Manual de usuario

HIK VISION

HIK VISION AX DS-PWA32-HSR Manual de usuario

HIK VISION

HIK VISION AX Series Manual de usuario

HIK VISION

HIK VISION DS-KH8340-TCE2 Manual de usuario

HIK VISION

HIK VISION AX PRO M2H Manual de usuario

HIK VISION

HIK VISION 1006KI Instrucciones de funcionamiento

HIK VISION

HIK VISION AX DS-PWA32-HSR Manual de usuario

HIK VISION

HIK VISION AX Series Manual de usuario

HIK VISION

HIK VISION AX DS-PW32-H Series Manual de usuario

HIK VISION

HIK VISION Pyronix EURO 280 Manual del propietario

HIK VISION

HIK VISION AX PRO Manual de usuario

HIK VISION

HIK VISION KH6 Series Manual de usuario

HIK VISION

HIK VISION DS-19A Series Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas