Hearth and Home Technologies BE-32 Manual de usuario

Hearth & Home Technologies • BE-32 • InD • 2099-985 Rev. C • 9/06 1

Model: BE-32

Owner’s Manual

Installation and Operation

• Do not store or use gasoline or other ﬂam-

mable vapors and liquids in the vicinity of

this or any other appliance.

• What to do if you smell gas

- Do not try to light any appliance

- Do not touch any electrical switch. Do not

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli-

er’s instructions.

- If you cannot reach your gas supplier, call

the ﬁre department.

• Installation and service must be performed

bya qualiﬁedinstaller,serviceagency, orthe

gas supplier.

WARNING: If the information in

these instructions is not followed

exactly, a ﬁre or explosion may result

causing property damage, personal

injury, or death.

This appliance has been supplied with an integral barrier

to prevent direct contact with the ﬁxed glass panel. Do

NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the

barrier is not present or help is needed to properly install one.

HOT! DO NOT TOUCH.

SEVERE BURNS MAY RESULT.

CLOTHING IGNITION MAY RESULT.

• CAREFULLY SUPERVISE children in same room as

appliance.

• Alert children and adults to hazards of high temperatures.

• Do NOT operate with protective barriers open or

removed.

• Keep clothing, furniture, draperies and other

combustibles away.

Glass and other surfaces are hot during

operation and cool down.

• Keep children away.

DO NOT DISCARD THIS MANUAL

CAUTION

This appliance may be installed as an OEM installation in

manufactured home (USA only) or mobile home and must be

installedinaccordancewiththemanufacturer’sinstructionsand

themanufactured home construction and safety standard,Title

24CFR,Part3280orStandardforInstallationinMobileHomes,

CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas indicated

on the rating plate.

Installation and service of this appliance should be

performed by qualiﬁed personnel. Hearth & Home

TechnologiessuggestsNFI certiﬁedor factory-trained

professionals, or technicians super-

vised by an NFI certiﬁed professional.

• Leave this manual with

party responsible for use

and operation.

DO NOT

DISCARD

WARNING

• Important operating

and maintenance

instructions included.

• Read,understandandfollow

these instructions for safe

installation and operation.

In the Commonwealth of Massachusetts:

• installation must be performed by a licensed plumber

or gas ﬁtter;

See Table of Contents for location of additional

Commonwealth of Massachusetts requirements.

Hearth & Home Technologies • BE-32 • InD • 2099-985 Rev. C • 9/06

Congratulations

Listing Label Information/Location

Model Name:___________________________________________ Date purchased/installed:__________________

Serial Number:__________________________________________ Location on appliance: ____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

Congratulations on selecting a Hearth & Home

Technologies gas appliance —an elegant and clean

alternative to wood burning appliances. The Hearth &

Home Technologies gas appliance you have selected is

designed to provide the utmost in safety, reliability, and

efﬁciency.

As the owner of a new appliance, you’ll want to read and

carefully follow all of the instructions contained in this

Owner’s Manual. Pay special attention to all Cautions

and Warnings.

This Owner’s Manual should be retained for future

reference. We suggest that you keep it with your other

important documents and product manuals.

The information contained in this Owner’s Manual, unless

noted otherwise, applies to all models and gas control

systems.

Your new Hearth & Home Technologies gas appliance will

give you years of durable use and trouble-free enjoyment.

Welcome to the Hearth & Home Technologies family of

appliance products!

Read this manual before installing or operating this appliance.

Please retain this owner’s manual for future reference.

We recommend that you record the following

pertinent information about your appliance.

Gas and Electric

Information

Model Number

Serial Number

Type of Gas

The model information regarding your speciﬁc appliance can be found on

the rating plate usually located in the control area of the appliance.

Homeowner Reference Information

Hearth & Home Technologies, Inc.

20802 Kensington Blvd., Lakeville, Mn 55044

Hearth & Home Technologies • BE-32 • InD • 2099-985 Rev. C • 9/06 3

- Table of Contents -

Î= Contains updated information.

Section 1: Listing and Code Approvals

A. Appliance Certiﬁcation................................... 4

B. Glass Speciﬁcations...................................... 4

C. BTU Speciﬁcations........................................ 4

D. High Altitude Installations .............................. 4

E. Non-Combustible Materials Speciﬁcation...... 4

F. Combustible Materials Speciﬁcation.............. 4

G. Requirements for the Commonwealth

of Massachusetts........................................... 5

Section 2: Getting Started

A. Design and Installation Considerations.........6

B. Tools and Supplies Needed........................... 6

C. Inspect Appliance and Components.............. 6

Section 3: Framing and Clearances

A. Selecting Appliance Location......................... 7

B. Constructing the Appliance Chase ................8

C. Clearances .................................................... 8

D. Mantel Projections......................................... 9

Section 4: Termination Locations

A.Vent Termination Minimum Clearances....... 10

Section 5: Vent Information and Diagrams

A. Vent Table Key............................................. 12

B. Use of Elbows.............................................. 12

C. Measuring Standards .................................. 12

D. Use of Flex Vent.......................................... 13

E. Vent Diagrams............................................. 14

Section 6: Vent Clearances and Framing

A. Pipe Clearances to Combustibles ............... 21

B. Wall Penetration Framing............................ 21

C. Vertical Penetration Framing....................... 22

Section 7: Appliance Preparation

A. Top Vent....................................................... 23

B. Rear Vent..................................................... 24

C. Securing and Leveling the Appliance ..........25

Section 8: Installing Vent Pipe

A. Assembly of Vent Sections for DVP Pipes .. 26

B. Disassembly of Vent Sections..................... 28

C. Installing Heat Shield and

Horizontal Termination Cap ........................ 30

D. Installing Roof Flashing and Vertical

Termination Cap .......................................... 32

Section 9: Gas Information

A. Fuel Conversions...................................... 34

B. Gas Pressures.......................................... 34

C. Gas Connection........................................ 34

Section 10: Electrical Information

A. Recommendation for Wire........................ 36

B. Connecting to the Appliance.....................36

C. Standing Pilot Ignition System Wiring....... 36

D. Junction Box Installation........................... 37

E. Wall Switch Installation for Fan................. 38

Section 11: Finishing

A. Mantel Projections.................................... 39

B.Facing Material......................................... 39

Section 12: Appliance Setup

A. Remove Shipping Materials...................... 40

B. Clean the Appliance.................................. 40

C. Accessories .............................................. 40

D. Ember and Lava Rock Placement............ 40

E. Positioning the Logs ................................. 41

F. Glass Assembly ........................................ 42

G. Grilles and Trim......................................... 42

Section 13: Operating Instructions

A. Before Lighting Appliance......................... 43

B. Lighting Appliance..................................... 44

C. After Appliance is Lit ................................. 45

D. Frequently Asked Questions..................... 45

Section 14: Troubleshooting

A. Standing Pilot Ignition System.................. 46

Section 15: Maintaining and Servicing Appliance........... 48

Section 16: Reference Materials

A. Appliance Dimension Diagram ................. 50

B. Vent Components Diagrams..................... 51

C. Service Parts ............................................ 56

D. Warranty ................................................... 60

E. Contact Information .................................. 61

Hearth & Home Technologies • BE-32 • InD • 2099-985 Rev. C • 9/06

B. Glass Speciﬁcations

Hearth&HomeTechnologiesappliancesmanufacturedwith

tempered glass may be installed in hazardous locations

such as bathtub enclosures as deﬁned by the Consumer

Product Safety Commission (CPSC). The tempered glass

has been tested and certiﬁed to the requirements of ANSI

Z97.1andCPSC16 CFR 1202(SafetyGlazing Certiﬁcation

Council SGCC# 1595 and 1597.Architectural Testing, Inc.

Reports 02-31919.01 and 02-31917.01).

This statement is in compliance with CPSC 16 CFR

Section 1201.5 “Certiﬁcation and labeling requirements”

which refers to 15 U.S. Code (USC) 2063 stating “…Such

certiﬁcate shall accompany the product or shall otherwise

be furnished to any distributor or retailer to whom the

product is delivered.”

Some local building codes require the use of tempered

glass with permanent marking in such locations. Glass

meeting this requirement is available from the factory.

Please contact your dealer or distributor to order.

NOTE: Thisinstallationmustconformwithlocalcodes.Inthe

absence of local codes you must comply with the National

Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A.

and the CAN/CGA B149 Installation Codes in Canada.

NOTINTENDED FOR USEAS A PRIMARYHEATSOURCE.

Thisapplianceistestedandapprovedaseithersupplemental

room heat or as a decorative appliance. It should not be fac-

tored as primary heat in residential heating calculations.

Listing and Code Approvals

D. High Altitude Installations

U.L.Listed gasappliances aretestedandapprovedwithout

requiring changes for elevations from 0 to 2000 feet in the

U.S.A. and Canada.

When installing this appliance at an elevation above 2000

feet, it may be necessary to decrease the input rating by

changing the existing burner oriﬁce to a smaller size. Input

rate should be reduced by 4% for each 1000 feet above

a 2000 foot elevation in the U.S.A., or 10% for elevations

between 2000 and 4500 feet in Canada. If the heating

value of the gas has been reduced, these rules do not

apply. To identify the proper oriﬁce size, check with the

local gas utility.

If installing this appliance at an elevation above 4500 feet

(in Canada), check with local authorities.

C. BTU Speciﬁcations

MODEL: BE-32

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Direct Vent Gas Appliance Heater

STANDARD: ANSI Z21.88-2002•CSA2.33-M02•UL307B

WARNING

DoNOTusethisapplianceifany part has beenunderwater.

Immediately call a qualiﬁed service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

This product is listed to ANSI standards for “Vented Gas

Appliance Heaters” and applicable sections of “Gas Burn-

ing Heating Appliances for Manufactured Homes and

RecreationalVehicles”,and “GasFiredAppliancesfor Use

at High Altitudes”.

Models

(U.S. or Canada) Maximum

Input BTUH Oriﬁce

Size (DMS)

BE-32 (NG) US

(0-2000 FT) 17,800 46

CANADA

(2000-4500 FT) 16,000 47

BE-32 (LP) US

(0-2000 FT) 15,500 56

CANADA

(2000-4500 FT) 13,680 57

A. Appliance Certiﬁcation

E. Non-Combustible Materials Speciﬁcation

Material which will not ignite and burn. Such materials are

those consisting entirely of steel, iron, brick, tile, concrete,

slate, glass or plasters, or any combination thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a

Vertical Tube Furnace at 750oC, shall be considered

non-combustible materials.

F. Combustible Materials Speciﬁcation

Materials made of or surfaced with wood, compressed

paper, plant ﬁbers, plastics, or other material that can

ignite and burn, whether ﬂame proofed or not, or whether

plastered or unplastered shall be considered combustible

materials.

Hearth & Home Technologies • BE-32 • InD • 2099-985 Rev. C • 9/06 5

For all side wall horizontally vented gas fueled equipment

installed in every dwelling, building or structure used in

whole or in part for residential purposes, including those

owned or operated by the Commonwealth and where

the side wall exhaust vent termination is less than seven

(7) feet above ﬁnished grade in the area of the venting,

includingbut notlimited todecksandporches,the following

requirements shall be satisﬁed:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal vented

gas fueled equipment, the installing plumber or gasﬁtter

shall observe that a hard wired carbon monoxide detector

with an alarm and battery back-up is installed on the

ﬂoor level where the gas equipment is to be installed. In

addition, the installing plumber or gasﬁtter shall observe

that a battery operated or hard wired carbon monoxide

detector with an alarm is installed on each additional level

of the dwelling, building or structure served by the side

wallhorizontal vented gasfueled equipment.It shall bethe

responsibility of the property owner to secure the services

of qualiﬁed licensed professionals for the installation of

hard wired carbon monoxide detectors.

Inthe eventthatthesidewall horizontallyvented gasfueled

equipmentisinstalled inacrawl spaceoran attic,thehard

wired carbon monoxide detector with alarm and battery

back-up may be installed on the next adjacent ﬂoor level.

In the event that the requirements of this subdivision can

not be met at the time of completion of installation, the

ownershallhave aperiod of thirty(30) daystocomply with

the above requirements; provided, however, that during

said thirty (30) day period, a battery operated carbon

monoxide detector with an alarm shall be installed.

Approved Carbon Monoxide Detectors

Eachcarbon monoxidedetectoras requiredin accordance

with the above provisions shall comply with NFPA720 and

be ANSI/UL 2034 listed and IAS certiﬁed.

Signage

Ametal or plastic identiﬁcation plate shall be permanently

mounted to the exterior of the building at a minimum

height of eight (8) feet above grade directly in line with

the exhaust vent terminal for the horizontally vented gas

fueled heating appliance or equipment. The sign shall

read, in print size no less than one-half (1/2) inch in size,

“GAS VENT DIRECTLY BELOW. KEEP CLEAR OFALL

OBSTRUCTIONS”.

Inspection

Thestate or localgas inspectorofthe sidewall horizontally

vented gas fueled equipment shall not approve the

installationunless, uponinspection, theinspector observes

carbon monoxide detectors and signage installed in

accordance with the provisions of 248 CMR 5.08(2)(a)1

through 4.

Exemptions

The following equipment is exempt from 248 CMR

5.08(2)(a)1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment

Not Required To Be Vented” in the most current edition

of NFPA54 as adopted by the Board; and

• Product Approved side wall horizontally vented gas

fueled equipment installed in a room or structure

separate from the dwelling, building or structure used

in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side wall

horizontally vented gas equipment provides a venting

system design or venting system components with the

equipment, the instructions provided by the manufacturer

for installation of the equipment and the venting system

shall include:

• Detailed instructions for the installation of the venting

system design or the venting system components; and

• A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side wall

horizontallyventedgas fueledequipment does notprovide

the parts for venting the ﬂue gases, but identiﬁes “special

venting systems”, the following requirements shall be

satisﬁed by the manufacturer:

• The referenced “special venting system” instructions

shallbeincluded withthe appliance orequipment instal-

lation instructions; and

• The“special ventingsystems”shallbeProductApproved

bythe Board,andtheinstructionsfor thatsystem shallin-

clude a parts list and detailed installation instructions.

Acopyofall installationinstructionsforallProductApproved

sidewall horizontallyvented gasfueled equipment,allvent-

inginstructions, allparts listsforventinginstructions,and/or

all venting design instructions shall remain with the appli-

ance or equipment at the completion of the installation.

See Gas Connection section for additional Common-

wealth of Massachusetts requirements.

G. Requirements for the Commonwealth of

Massachusetts

NOTE: The following requirements reference various

Massachusetts and national codes not contained in this

document.

Hearth & Home Technologies • BE-32 • InD • 2099-985 Rev. C • 9/06

A. Design and Installation Considerations

Hearth & Home Technologies direct vent gas appliances

are designed to operate with all combustion air siphoned

from outside of the building and all exhaust gases ex-

pelled to the outside. No additional outside air source is

required.

Getting Started

C. Inspect Appliance and Components

When planning an appliance installation, it’s necessary to

determine the following information before installing:

• Where the appliance is to be installed.

• The vent system conﬁguration to be used.

• Gas supply piping.

• Electrical wiring.

• Framing and ﬁnishing details.

• Whether optional accessories—devices such as a fan,

wall switch, or remote control—are desired.

B. Tools and Supplies Needed

Before beginning the installation be sure that the following

tools and building supplies are available.

Reciprocating saw Framing material

Pliers Hi temp caulking material

Hammer Gloves

Phillips screwdriver Framing square

Flat blade screwdriver Electric drill and bits (1/4 in.)

Plumb line Safety glasses

Level 1/2 - 3/4 inch length, #6 or #8 Self-drilling screws

Manometer Voltmeter

Tape measure Noncorrosive leak check solution

One 1/4 inch female connection (for optional fan).

• Carefully remove the appliance and components from

the packaging.

• Theventsystemcomponentsandtrimdoorsareshipped

in separate packages.

• The gas logs may be packaged separately and must

be ﬁeld installed.

• Report to your dealer any parts damaged in shipment,

particularly the condition of the glass.

• Read all of the instructions before starting the in-

stallation. Follow these instructions carefully dur-

ing the installation to ensure maximum safety and

beneﬁt.

Check building codes prior to installation.

• Installation MUST comply with local, regional, state

and national codes and regulations.

• Consult local building, ﬁre ofﬁcials or authorities

having jurisdiction about restrictions, installation

inspection, and permits.

CAUTION

Keep appliance dry.

• Mold or rust may cause odors.

• Water may damage controls.

WARNING

Inspect appliance and components for

damage. Damaged parts may impair safe

operation.

WARNING

• Do NOT install damaged components.

• Do NOT install incomplete components.

• Do NOT install substitute components.

Report damaged parts to dealer.

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be

voided by, the following actions:

• Installation and use of any damaged

appliance or vent system component.

WARNING

• Modiﬁcation of the appliance or vent system.

• Installation other than as instructed by Hearth & Home

Technologies.

• Improper positioning of the gas logs or the glass door.

• Installation and/or use of any component part not

approved by Hearth & Home Technologies.

Any such action may cause a ﬁre hazard.

Hearth & Home Technologies • BE-32 • InD • 2099-985 Rev. C • 9/06 7

3Framing and Clearances

NOTE:

•Illustrations reﬂect typical installations and are FOR

DESIGN PURPOSES ONLY.

•Illustrations/diagrams are not drawn to scale.

•Actual installation may vary due to individual design

preference.

WARNING

Fire Risk

Provide adequate clearance:

• Around air openings

• To combustibles

• For service access

Locate appliance away from trafﬁc areas.

A. Selecting Appliance Location

Whenselecting alocation foryour applianceit isimportantto

consider the required clearances to walls (see Figure 3.1).

Figure 3.1 Appliance Locations

NOTE: For actual appliance dimensions refer to Sec-

tion 16.

In addition to these framing dimensions, also reference the following sections:

• Clearances and Mantel Projections (Section 3.C and 3.D)

• Vent Clearances and Framing (Section 6).

ABC DEF G H I

Inches 39-3/8 34 55-5/8 37-3/8 1 1/2 46-1/16 65-1/8 52-1/16

mm 1000 864 1413 949 25 13 1170 1654 1322

Hearth & Home Technologies • BE-32 • InD • 2099-985 Rev. C • 9/06

Fire Risk.

•Construct chase to all clearance

speciﬁcations in manual.

•Locate and install appliance to all

clearance speciﬁcations in manual

WARNING

B. Constructing the Appliance Chase

A chase is a vertical boxlike structure built to enclose the

gasappliance and/orits ventsystem. Verticalvents thatrun

on the outside of a building may be, but are not required to

be, installed inside a chase.

Construction of the chase may vary with the type of building.

These instructions are not substitutes for the requirements

of local building codes. Local building codes MUST be

checked.

Chasesshouldbe constructed inthe manner ofall outside

walls of the home to prevent cold air drafting problems.

The chase should not break the outside building envelope

in any manner.

Walls, ceiling, base plate and cantilever ﬂoor of the chase

shouldbe insulated.Vaporandair inﬁltrationbarriersshould

beinstalled inthechaseasper regionalcodes fortherest of

the home.Additionally, in regions where cold air inﬁltration

may be an issue, the inside surfaces may be sheetrocked

and taped for maximum air tightness.

To furtherpreventdrafts,thewall shieldandceilingﬁrestops

shouldbe caulkedwithhightemperaturecaulk tosealgaps.

Gas line holes and other openings should be caulked with

C. Clearances

Figure 3.2 Clearances to Combustibles

Fire Risk.

Odor Risk.

•Install appliance on hard metal or wood

surfaces extending full width and depth of

appliance.

•Do NOT install appliance directly on

carpeting, vinyl, tile or any combustible

material other than wood.

WARNING

high temp caulk or stuffed with unfaced insulation. If the

appliance is being installed on a cement slab, a layer of

plywood may be placed underneath to prevent conducting

cold up into the room.

FROM TOP

OF HOOD

TO CEILING

ABCDE F GHIJ

Rough

Opening

(Vent Pipe)

Rough

Opening

(Height)

Rough

Opening

(Depth)

Rough

Opening

(Width)

Clearance

to Ceiling

(From Top of

Hood)

Non-Combustible

Floor Combustible

Flooring Behind

Appliance Sides of

Appliance Front of

Appliance

PIPE Inches 8-5/8 31 16-1/4 34 32 0 0 1/2 1/2 36

mm 219 787 413 864 813 0 0 13 13 914

DVP

PIPE Inches 10 31 27-1/2 34 32 0 0 1/2 1/2 36

mm 254 787 699 864 813 0 0 13 13 914

Hearth & Home Technologies • BE-32 • InD • 2099-985 Rev. C • 9/06 9

D. Mantel Projections

Figure 3.3 Clearances to Mantels or other

Combustibles above Appliance

Figure 3.4 Clearances to Mantel Legs or Wall Projections

(Acceptable on both sides of opening.)

1”

2”

Note: Clearance

from opening to

perpendicular wall.

Hearth & Home Technologies • BE-32 • InD • 2099-985 Rev. C • 9/06

A. Vent Termination Minimum Clearances

Fire Risk.

Explosion Risk.

Maintain vent clearance to combustibles as

speciﬁed.

WARNING

• Do not pack air space with insulation or

other materials.

Failure to keep insulation or other materials

away from vent pipe may cause ﬁre.

Roof Pitch H (Min.) Ft.

Flat to 6/12...........................................................1.0*

Over 6/12 to 7/12.................................................1.25*

Over 7/12 to 8/12.................................................1.5*

Over 8/12 to 9/12.................................................2.0*

Over 9/12 to 10/12...............................................2.5

Over 10/12 to 11/12.............................................3.25

Over 11/12 to 12/12.............................................4.0

Over 12/12 to 14/12.............................................5.0

Over 14/12 to 16/12.............................................6.0

Over 16/12 to 18/12.............................................7.0

Over 18/12 to 20/12.............................................7.5

Over 20/12 to 21/12.............................................8.0

Figure 4.1

Figure 4.2 Minimum Height from Roof to

Lowest Discharge Opening

Termination Locations

Measure horizontal clearances from this surface.

Measure vertical clearances from this surface.

Figure 4.3 Multiple Vertical Termination

Figure 4.2 speciﬁes minimum vent heights for various

pitched roofs.

(See Figure 4.4 for speciﬁc clearances)

* 3 foot minimum in snow regions

H (MIN.) - MINIMUM HEIGHT FROM ROOF

TO LOWEST DISCHARGE OPENING

Gas Termination Wood & Fuel Oil Termination

A6 in. 20 in.

20 IN.

(MINIMUM) TO

PERPENDICULAR

WALL

(GAS ONLY)

GAS

TERMINATION

GAS, WOOD OR FUEL

OIL TERMINATION

Tabla de contenidos

Otros manuales de Chimenea de interior de Hearth and Home Technologies

Hearth and Home Technologies

Hearth and Home Technologies Outdoor Lifestyles ODPLAZA-L24S-B Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies outdoor lifestyle ODCTGWD-36 Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies GO318-IPI-NG Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies CFL-18NG-C Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies Outdoor Lifestyles ODLANAIG-48 Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies Heat & Glo EM-415 Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies 350TRSI-AUF Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies outdoor lifestyles LUM-OD-NM Instrucciones de funcionamiento

Hearth and Home Technologies

Hearth and Home Technologies outdoor lifestyles Dakota 42-CE Instrucciones de montaje

Hearth and Home Technologies

Hearth and Home Technologies GO35MTCH Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies RBV4236IH Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies BE-36-C Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies BE-36-C Instrucciones de montaje

Hearth and Home Technologies

Hearth and Home Technologies Simplifyre SFE-35 Instrucciones de montaje

Hearth and Home Technologies

Hearth and Home Technologies Simplifyre SFE-35 Instrucciones de montaje

Hearth and Home Technologies

Hearth and Home Technologies MEZZO Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies Quadra-Fire EXPEDITIONII-AU Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies Simplifyre SFE-26 Instrucciones de montaje

Hearth and Home Technologies

Hearth and Home Technologies Crescent II Door Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies BRAVO Instrucciones de montaje

Hearth and Home Technologies

Hearth and Home Technologies AZTEC Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies 6000BE Manual de usuario

Hearth and Home Technologies

Hearth and Home Technologies Simplifyre SFE-35 Instrucciones de instalación

Hearth and Home Technologies

Hearth and Home Technologies GO24-IPI-LP Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación