Health O Meter Pro Plus 2101KL Manual de usuario

Model 2101KL

Digital Platform Scale

User Instructions

P/N UM2101KLE_ Rev20170710

Model 2101KL

Thank you for your purchase of this Health o meter®Professional product. Please read

this manual carefully, and keep it for easy reference or training.

TABLE OF CONTENTS

Cautions and Warnings.............................................................................................3

Specifications............................................................................................................4

Certifications / Connectivity / Disposal ......................................................................5

Assembly Instructions ..............................................................................................6

Set-up Instructions ...................................................................................................10

Operating Instructions...............................................................................................13

Maintenance..............................................................................................................19

Calibration....…………………………………..………………………………..……….…..20

Troubleshooting …………………………………………………………………………….22

Warranty..…………………………………………………………………………………….23

Note: This scale has been factory calibrated, and does not

require calibration prior to use.

Please register your scale for warranty coverage at:

www.homscales.com

For User Instructions updates and revisions please go to:

www.homscales.com

CAUTIONS AND WARNINGS

To prevent injury and damage to your scale, please follow these instructions very

carefully.

Assemble and operate the scale per the enclosed user instructions.

Do not transport the scale with any weight on the platform.

Do not exceed weight limit of 1000 lb / 454 kg for this scale.

For accurate weighing, this scale must be placed on a flat, stable surface.

For accurate weighing, verify before each use the proper operation

according to the procedure described in this manual.

Do not use in the presence of flammable or explosive materials.

For accurate weighing, if the battery icon indicates that the battery is low,

replace the batteries or switch to theAC adapter as soon as possible.

When replacing / inserting batteries, be sure to use all new batteries.

To prevent patient injury, the patient must be attended throughout the entire weighing

event. Caregivers should ensure that the patient is stable and provide support as

needed when getting onto and off of the scale.

Patient should wear socks or other form of lightweight foot covering during weighing

event.

Using the Scale with the Optional AC Adapter

Operate this scale exclusively with the AC adapter provided by Health o meter®

Professional. Use of an unspecified adapter will void the warranty and can pose

a serious safety hazard.

Operating this scale at voltages and frequencies other than specified can

damage the equipment and will void the warranty.

Prior to using this scale, inspect the AC adapter cord for cracking /

fraying, and for broken / bent plug prongs.

Prior to using this scale, ensure that the AC adapter is plugged into an

outlet with the rated voltage appropriate for operation.

Ensure that the AC adapter outlet is wired to a circuit breaker or other

protected power source.

Unplug the AC adapter, and carefully store both the adapter and adapter

cord before moving the scale.

Ensure that theAC adapter and scale do not come in contact with liquids,

excessive temperature, or excessive humidity.

If the scale is being connected to another medical device, the power

adapter must not be used. Disconnect the power adapter from the scale

and use only the battery power.

SPECIFICATIONS

General

Model 2101KL digital scales use highly sophisticated microprocessor technology. Each

precision scale is designed to provide accurate, reliable and repeatable weight

measurements. This scale uses motion-sensing weighing technology in order to

determine the actual weight of a moving patient.

Although the patient’s weight can be displayed in either pounds (LB) or kilograms (KG),

the scale can be “locked” such that the user cannot change the displayed Unit of

Measurement (UOM).

Scale Specifications

Capacity and

Resolution

1000 lb x 0.2 lb (454 kg x 0.1 kg)

Power Requirements

110-240VAC, 50-60Hz to 9V DC Adapter, ADPT30 (included) or 6 D batteries

(not included)

Environmental

Operating temperatures: 50°F to 95°F (10°C to 35°C)

Storage temperatures: 30°F to 125°F (0°C to 50°C)

Maximum Humidity: 85% RH

Physical Dimensions

Platform

Length: 22” (559mm)

Width: 26” (660mm)

Height: 2-3/8” (60mm)

Assembled Size

Length: 27” (686mm)

Width: 31” (787mm)

Height: 50” (1270mm)

Scale information can also be found by pressing and selecting “Scale Info” in the

submenu. This screen provides model number, capacity, calibration weight, the most

recent field calibration date, number of field calibrations and software version.

Help

CERTIFICATIONS / CONNECTIVITY / DISPOSAL

Certification Descriptions

Connectivity Information

To enable reliable transmission of weight, height, and Body Mass Index (BMI) data, this

scale is designed to interface with a computer, EMR software or other electronic device

via various Health o meter®Professional Connectivity Solutions. This connectivity helps

minimize transcription errors when recording patient data.

For more information regarding how to connect this scale to other electronic devices,

please contact Health o meter®Professional Scales Technical Support at 1-800-638-

3722 or visit www.homscales.com/innovations/connectivity-solutions.

Scale Disposal

This Health o meter®Professional scale must be disposed of properly as electronic

waste. Follow the national, regional or local regulations which apply to you for disposal

of electronic waste or batteries. Do not dispose of this device in the domestic waste

stream.

Pelstar, LLC has been officially certified as the manufacturer

of Health o meter®Professional medical devices. The Pelstar,

LLC quality assurance system covers the development,

production, sales and service of medical scales and

measuring systems.

ASSEMBLY INSTRUCTIONS

Before Assembly

Carefully inspect the carton for shipping damage before unpacking. If damage is found, contact

your shipper or a Health o meter®Professional representative immediately at 1-800-815-6615.

Claims must be filed with the shipper as soon as possible after receipt of the package. The

following information details what you will find inside the main carton as you unpack the parts for

assembly.

To prevent scratching any components, carefully remove each assembly from the carton and

unwrap the packing materials. Set the carton aside for storage. To avoid damaging the scale

parts when unpacking, do not use a box cutter, knife, scissors, or any sharp object to open the

protective inner packaging.

Parts List

(2) Side handrails (Parts A and C)

(1) Center handrail (Part B)

(1) Scale platform/base (Part D)

(1) Handle (Part E)

(1) Brown box containing:

(1) Box containing the AC adapter

(1) Display Head

(1) User Information

(1) White box containing:

o(4) Feet

o(1) AC adapter holder

o(1) 4mm Allen wrench

o(1) 5mm Allen wrench

o(1) 8mm Allen wrench

o(1) Plastic bracket cover

oHardware for assembly:

- A –M10 1.5 x 40mm bolts, Qty.2

- B –M8 1.25 x 20mm bolts, Qty. 16

- C –M6 1.0 x 10mm bolts, Qty.2

- D –#8 ½ sheet metal screws, Qty. 2

- E –M4 0.7 x 10mm screws, Qty.6 for assembly, 1 spare

- F –M8 washers, Qty. 16

Tools Required

Phillips head screwdriver (not included), Allen wrenches (included).

Figure 1 –Scale Parts

Handle (Part E)

Left Side Handrail

(Part A)

Right Side

Handrail (Part C)

Center Handrail

(Part B)

Platform/Base

(Part D)

Brown Box Contents

White Box Contents

Hardware Detail

ASSEMBLY INSTRUCTIONS (CONT.)

Health o meter® Professional Scales recommends that assembly is performed by

two people.

Warning: Do not drop scale, as this can permanently damage the load cells.

Caution: Do not insert the batteries into the display head until it is mounted onto

the scale.

1. Remove the scale platform/base (part D,

see Figure 1 on page 6) from the carton

and place on a flat, level, and dry

surface. Locate the center handrail (part

B) and the load cell cable protruding

from the bottom of the right side. Feed

the load cell cable into the large center

hole of the right handrail mounting hole

in the scale base.

2. Position the center handrail over the left

and right mounting holes on the scale

base. Be sure not to pinch the cable.

Place the (8) M8 washers onto the (8)

M8 1.25 x 20mm bolts and insert into the

mounting holes on the scale base, lightly

tighten using the included 5mm Allen

wrench. Do not over tighten.

3. Align the left and right side handrails

(parts A and C) with the mounting holes

in the platform. Place the (8) M8 washers

onto the (8) M8 1.25 x 20mm bolts and

insert into the mounting holes on the

platform. Lightly tighten using the 5mm

Allen wrench.

4. Align the left and right side handrails

with the holes on the front of the left

and right sides of the center handrail.

Obtain the (2) M10 1.5 x 40mm bolts

and insert into the left and right holes

on the back of the center handrail.

Using the included 8mm Allen

wrench, fully tighten the two M10

bolts and then fully tighten all bolts

starting from the top of the scale

down to the platform.

ASSEMBLY INSTRUCTIONS (CONT.)

5. Pull forward on the side handrails to tip

the scale and gently place it face down

on the floor. Grasp the load cell cable

protruding from the bottom of the

platform and feed it through the

protective metal shield.

6. Plug the load cell cable into the load cell

port located on the back of the platform.

Pull the excess cable through the top of

the center handrail.

7. Thread the (4) feet into the underside of

the platform. Each foot should be

completely hand tightened then back the

feet out 1-½ full turns. This allows for

proper load cell operation. Carefully tilt

the scale back to an upright position on

the floor. Warning: Do not drop scale,

as this can permanently damage the

load cells. Adjust the feet to level the

scale. Be certain that the feet are not

completely tightened into the platform.

8. Obtain the display head and align the

four holes on the back of the display

head with the four mounting holes on

the silver display support. Using the (4)

included M4 x 0.7 x 10mm screws,

fasten the display head onto the display

support using a Phillips head

screwdriver to tighten the screws.

ASSEMBLY INSTRUCTIONS (CONT.)

9. Route the load cell cable to the side and

then between the washer and the silver

lip in the bracket. Clip the load cell cable

into the divot in the middle of the cover.

Obtain the plastic bracket cover and the

two remaining M4 x 0.7 x 10mm machine

screws. Using a Phillips screwdriver,

attach the bracket cover over the silver

display bracket.

10. Plug the load cell cable into the load cell

port on the rear of the display head.

11. Obtain the handle (part E) and align it

with the ends of the side handrails. Insert

the (2) medium M6 1.0 x 10mm bolts into

the holes on the underside of the handle.

Using the included 4mm Allen wrench,

attach the handle to the center handrail.

The handle should be attached with the

Warning label facing up.

12. Attach the adapter holder to the handrail

using the (2) included sheet metal

screws. Use a Phillips head screwdriver

to tighten the screws. The scale is now

assembled. See Powering the Scale on

page 10 for battery/AC adapter

instructions.

SET-UP INSTRUCTIONS

Powering the Scale

Plug the AC adapter into the power adapter jack (the jack is located on the rear of the display

head), then plug the scale’s AC adapter into the power source.

Warning: To avoid a safety hazard, do not use an unspecified AC adapter. Only use the

Health o meter® Professional AC adapter model ADPT30 designed for this scale.

For battery operation, see Battery Installation below.

Battery Installation

1. If connected, unplug the AC adapter from

the power source. Use a Phillips head

screwdriver to remove the battery cover

on the side of the display head by

unscrewing the battery cover screw.

2. Remove the battery pack from the

display head. Replace or install fresh

batteries, making sure to install them in

the proper direction. Health o meter®

Professional recommends using an

alkaline battery rated for 130°F (54°C)

operation. Do not use Zinc-Carbon

batteries.

3. Re-insert the battery pack into the

display head, ensuring the end with the

silver contacts is inserted facing the

inside of the display. Re-attach the

battery cover to the display head by

replacing the battery cover screw.

Warning: If the scale will not be used for some time, remove the batteries to avoid a safety

hazard. Disposal of batteries must be performed in accordance with the prevailing national,

regional or local regulations that apply to you.

Power Adapter

Jack

Otros manuales para Pro Plus 2101KL

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escala de Health O Meter

Health O Meter

Health O Meter HDM166-60 Manual de usuario

Health O Meter

Health O Meter 500KL Manual de usuario

Health O Meter

Health O Meter Pro Plus 2101KL Manual de usuario

Health O Meter

Health O Meter 553KL Manual de usuario

Health O Meter

Health O Meter HNY200 Manual de usuario

Health O Meter

Health O Meter PROPLUS 4024 Manual de usuario

Health O Meter

Health O Meter HDR900 Manual de usuario

Health O Meter

Health O Meter BCS-G6 Series Manual de usuario

Health O Meter

Health O Meter Pro Plus 2101KL Manual de usuario

Health O Meter

Health O Meter PROPLUS 1100KL Manual de usuario

Health O Meter

Health O Meter 2595KL Guía de instalación

Health O Meter

Health O Meter 500KL Manual de usuario

Health O Meter

Health O Meter 2210KL Manual de usuario

Health O Meter

Health O Meter 1101KL Manual de usuario

Health O Meter

Health O Meter 597KL Manual de usuario

Health O Meter

Health O Meter 2842KL Manual de usuario

Health O Meter

Health O Meter 2400KL Manual de usuario

Health O Meter

Health O Meter 522KL Manual de usuario

Health O Meter

Health O Meter HAB979 Manual de usuario

Health O Meter

Health O Meter HDL489-60 Manual de usuario

Health O Meter

Health O Meter HDM575 Manual de usuario

Health O Meter

Health O Meter Professional 502KL Manual de usuario

Health O Meter

Health O Meter 600KL Manual de usuario

Health O Meter

Health O Meter BFM884DQ1-60 Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario