HBM FIT 7A Manual de usuario
Operating Manual | Bedienungsanleitung |
Manuel d'emploi | Istruzioni per l'uso
English Deutsch Français Italiano
FIT®7A
Hottinger Baldwin Messtechnik GmbH
Im Tiefen See 45
D-64239 Darmstadt
Tel. +49 6151 803-0
Fax +49 6151 803-9100
www.hbm.com
Mat.: 7-2004.3924
DVS: A3924-1.1 HBM: public
09.2015
EHottinger Baldwin Messtechnik GmbH.
Subject to modifications.
All product descriptions are for general information only.
They are not to be understood as a guarantee of quality or
durability.
Änderungen vorbehalten.
Alle Angaben beschreiben unsere Produkte in allgemeiner
Form. Sie stellen keine Beschaffenheits- oder Haltbarkeits
garantie dar.
Sous réserve de modifications.
Les caractéristiques indiquées ne décrivent nos produits
que sous une forme générale. Elles n'impliquent aucune
garantie de qualité ou de durablilité.
Con riserva di modifica.
Tutti i dati descrivono i nostri prodotti in forma generica e non
implicano alcuna garanzia di qualità o di durata dei prodotti
stessi.
Operating Manual | Bedienungsanleitung |
Manuel d'emploi | Istruzioni per l'uso
English Deutsch Français Italiano
FIT®7A
2A3924-1.1 HBM: public FIT®7A
English
1 Safety instructions 4........................................
2 Markings used 8............................................
2.1 Symbols on the device 8......................................
2.2 The marking used in this document 8...........................
3 Conditions on site 10........................................
3.1 Protection against corrosion 10.................................
3.2 Deposits 10..................................................
4 Mechanical installation 12....................................
4.1 Important precautions during installation 12......................
4.2 Mounting and load application 13...............................
4.3 Connection for pressure compensation 14........................
5 Electrical connection 15......................................
6 Interfaces 18................................................
6.1 Connection of several load cells to a PC via RS-485 18............
6.2 Connection to a PC with an RS‐232 interface via the HBM interface
converter 19.................................................
6.3 Connection to a CANopen interface 19..........................
6.4 Connection to a DeviceNet interface 20..........................
6.5 Diagnostic interface connection 20..............................
7 Inputs and outputs 21........................................
7.1 Inputs 21....................................................
7.2 Outputs 22...................................................
Safety instructions
4A3924-1.1 HBM: public FIT®7A
1 Safety instructions
Appropriate use
Transducers of the FIT7A type series are designed solely
for technical weighing applications within the application
limits detailed in the specifications. Any other use is not
appropriate.
Any person instructed to carry out installation, commis
sioning or operation of the transducer must have read
and understood the Operating Manual and in particular
the technical safety instructions.
In the interests of safety, the transducer should only be
operated by qualified personnel and as described in the
Operating Manual. It is also essential to comply with the
legal and safety requirements for the application con
cerned during use. The same applies to the use of
accessories.
The transducer is not intended for use as a safety com
ponent. Please also refer to the "Additional safety pre
cautions" section. Proper and safe operation requires
proper transportation, correct storage, siting and mount
ing, and careful operation.
Operating conditions
SPlease observe the permissible maximum values
stated in the specifications for:
- Limit load
- Limit load at max. eccentricity
- Limit lateral loading
- Breaking loads
- Temperature limits
Safety instructions
FIT®7A A3924-1.1 HBM: public 5
- Limits of electrical load-carrying capacity
SPlease note that when several transducers are
installed in a scale, there is not always an even distri
bution of load on the individual transducers.
SThe transducers can be used as machine elements.
When used in this manner, it must be noted that, to
favor greater sensitivity, the transducer is not
designed with the safety factors usual in mechanical
engineering.
SThe transducer must not be modified from the design
or safety engineering point of view except with our
express agreement.
SThe transducer is maintenance-free.
SIn accordance with national and local environmental
protection and material recovery and recycling regula
tions, old transducers that can no longer be used
must be disposed of separately and not with normal
household garbage, see Chapter 9, Page 25.
Qualified personnel
Qualified persons means persons entrusted with the
installation, fitting, commissioning and operation of the
product who possess the appropriate qualifications for
their function.
This includes people who meet at least one of the three
following requirements:
SKnowledge of the safety concepts of measurement
and automation technology is a requirement and as
project personnel, they must be familiar with these
concepts.
SAs measurement or automation plant operating per
sonnel, they have been instructed how to handle the
Safety instructions
6A3924-1.1 HBM: public FIT®7A
machinery. They are familiar with the operation of the
equipment and technologies described in this docu
mentation.
SAs commissioning engineers or service engineers,
they have successfully completed the training to qual
ify them to repair the automation systems. They are
also authorized to activate, ground and label circuits
and equipment in accordance with safety engineering
standards.
Working safely
SThe device must not be directly connected to the
power supply system. The supply voltage must be
between 10 and 30 VDC.
SError messages should only be acknowledged once
the cause of the error is removed and no further dan
ger exists.
SMaintenance and repair work on an open device with
the power on may only be carried out by trained per
sonnel who are aware of the dangers involved.
SAutomation equipment and devices must be designed
in such a way that adequate protection or locking
against unintentional actuation is provided (e.g.
access checks, password protection, etc.).
SFor those devices operating in networks, safety pre
cautions must be taken both in terms of hardware and
software, so that a line break or other interruptions to
signal transmission do not cause undefined states or
loss of data in the automation device.
SAfter making settings and carrying out activities that
are password-protected, ensure that any controls that
may be connected remain in a safe condition until the
switching performance of the device has been tested.
Safety instructions
FIT®7A A3924-1.1 HBM: public 7
Additional safety precautions
Additional safety precautions to meet the requirements of
the relevant national and local accident prevention regu
lations must be taken in plants where malfunctions could
cause major damage, loss of data or even personal
injury.
The scope of supply and performance of the transducer
covers only a small area of measurement technology.
Before starting up the transducer in a system, a project
planning and risk analysis must first be implemented,
taking into account all the safety aspects of measure
ment and automation technology so that residual risks
are minimized. This particularly concerns personal and
machine protection. The transducers function passively
and cannot implement any (safety-relevant) cutoffs. In
the event of a fault, the relevant precautions must estab
lish safe operating conditions.
General dangers of failing to follow the safety
instructions
The transducer corresponds to the state of the art and is
reliable. The transducer may give rise to residual dangers
if it is inappropriately installed or operated.
Markings used
8A3924-1.1 HBM: public FIT®7A
2 Markings used
2.1 Symbols on the device
Statutory waste disposal mark
In accordance with national and local environmental pro
tection and material recovery and recycling regulations,
old devices that can no longer be used must be disposed
of separately and not with normal household garbage.
Also see Section 9 on Page 25.
CE mark
The CE mark enables the manufacturer to guarantee that
the product complies with the requirements of the rele
vant EC directives (the Declaration of Conformity can be
found on the HBM website (www.hbm.com) under
HBMdoc).
2.2 The marking used in this document
Important instructions for your safety are specifically
identified. It is essential to follow these instructions in
order to prevent accidents and damage to property.
Symbol Significance
WARNING This marking warns of a potentially dangerous situ
ation in which failure to comply with safety require
ments can result in death or serious physical injury.
Note This marking draws your attention to a situation in
which failure to comply with safety requirements can
lead to damage to property.
Otros manuales para FIT 7A
1
Tabla de contenidos
Idiomas:
Otros manuales de Transductor de HBM
HBM
HBM CFT+ Series Manual de usuario
HBM
HBM C9B Manual de usuario
HBM
HBM T40MS Manual de usuario
HBM
HBM T4A Manual de usuario
HBM
HBM AED9301B Manual de usuario
HBM
HBM WI Series Manual de usuario
HBM
HBM Z16A Manual de usuario
HBM
HBM C18 Manual de usuario
HBM
HBM Z8 Manual de usuario
HBM
HBM Paceline CFT Manual de usuario
HBM
HBM Z30A Manual de usuario
HBM
HBM P8AP Manual de usuario
HBM
HBM P6A Manual de usuario
HBM
HBM Z30 Manual de usuario
HBM
HBM U9B Manual de usuario
HBM
HBM U10M Manual de usuario
HBM
HBM TB2 Manual de usuario
HBM
HBM SLB700A/06VA1 Manual de usuario
HBM
HBM AD104-R2 Manual de usuario
HBM
HBM P3MBP Manual de usuario
Manuales populares de Transductor de otras marcas
Camille Bauer
Camille Bauer SINEAX F534 Manual de usuario
Trane
Trane KIT 16724 Instrucciones de montaje
Lumel
Lumel P18 Manual de usuario
B&C Speakers
B&C Speakers DE75PTN Manual de usuario
MAMAC SYSTEMS
MAMAC SYSTEMS PR-243 Manual
Mianyang Weibo Electronic
Mianyang Weibo Electronic WB Series Manual de usuario
