Hayward AQR100 Manual de usuario

Otros manuales para AQR100

2

Este manual sirve para los siguientes modelos

1

Otros manuales de Controladores de Hayward

Hayward

Hayward ColorLogic LKCUS1100 Manual de usuario

Hayward

Hayward Aqua Solar GL-235 Hoja de especificaciones

Hayward

Hayward RSR3 Series Manual

Hayward

Hayward Pool Rx LT Manual de usuario

Hayward

Hayward CAT 2000 W3CATPP2000 Manual de usuario

Hayward

Hayward Aqua Plus® Manual de usuario

Hayward

Hayward VS Omni Manual de usuario

Hayward

Hayward HLXPLCONTROL Manual de usuario

Hayward

Hayward Aqua Plus® Manual de usuario

Hayward

Hayward HLXPLCONTROL Manual de usuario

Hayward

Hayward CAT 5000 Manual de usuario

Hayward

Hayward GLX-PCB-HPC-4 Manual de usuario

Hayward

Hayward ColorLogic LKCUS1100 Manual de usuario

Hayward

Hayward OmniLogic HTG-OL150c Guía del administrador

Hayward

Hayward HRSN6 series Manual

Hayward

Hayward CAT-1000-ORP Manual de usuario

Hayward

Hayward HCC 4000 Manual de usuario

Hayward

Hayward Aqua Plus® Manual de usuario

Hayward

Hayward HRSN2 series Manual

Hayward

Hayward HRSN2 series Manual

Hayward

Hayward HRSN3 series Manual

Hayward

Hayward E-Command® 4 Manual de usuario

Hayward

Hayward HCC 1000 Manual de usuario

Hayward

Hayward OmniPL Retrofit Kit Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

Hayward Pool Products

620 Division Street, Elizabeth NJ 07207

Phone (908)-355-7995

www.hayward.com

AQR100

Replacement PCB for AQR100

Installation Manual

GLXAQR100PCB

Contents

Description............................1

Installation............................1

092004 RevA

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Description

The GLXAQR100PCB is a replacement printed circuit board (PCB) for the AQR100 chlorine genera-

tor only.

Installation

DANGER of Death, Injury or Property Damage if procedure not followed. This component

connects to the main circuit and chlorinator cell inside of the AQR100 enclosure. Separating the

enclosure is required. Power to the AQR100 MUST be shut off before the enclosure is separated.

1. Completely remove power to the AQR100.

2. Remove the AQR100 from the mounted surface.

3 Remove the 10 stainless steel screws from the back of the AQR100.

4. As you carefully separate the enclosure, reach in and remove the ribbon cable connector.

After the cable has been disconnected, remove the front half of the enclosure and put it

aside.

Remove the 10

fasteners shown

using a #2 Phillips

head screwdriver.

Pull straight up on the

connector to remove

the ribbon cable before

fully separating the

enclosure.

1

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

5. Looking down into the enclosure. Locate and remove the two connectors from the PCB as

shown.

6. There is a green wire that is connected to the PCB as shown below. Pull up on this wire to

disconnect it.

Separate this connector by

pinching the two outer tabs and

pulling up.

Pull straight up to remove the green conductor.

Separate this connector by

pushing down on the top lever

and pulling apart.

7. You can now remove the 4 Phillips head screws that fasten the PCB to the enclosure and then

remove the PCB.

8. To install the new PCB, reverse the previous steps.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

2

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

2

For further information or consumer

technical support, visit our website at

www.hayward.com

Hayward is a registered trademark and AQR100 is

a trademark of Hayward Industries, Inc. © 2019 Hayward Industries, Inc.

All other trademarks not owned by Hayward are the property of their respective owners.

Hayward is not in any way afﬁliated with or endorsed by those third parties.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS