Harken Performa Winch 60.2 STP Manual

Performa™Winch 60.2 STP

Installation and Maintenance Manual

MRPW-D

Performa™Winch 60.2 STP

Installation and Maintenance Manual - Mod.D

Index

Introduction 3

Technical characteristics 3

Weight 3

Maximum working load 3

Outline 3

Installation 4

Installation procedure 7

Positioning the self-tailing arm 8

Maintenance 8

Washing 8

Maintenance table 8

Disassembly procedure 8

Exploded view with maintenance products 12

Assembly 13

Harken®limited worldwide warranty 14

Ordering spare parts 14

Exploded view 15

Parts list 17

Performa™Winch 60.2 STP

Installation and Maintenance Manual - Mod.D

Introduction - Technical characteristics - Outline

Introduction

This manual gives technical information on winch installation and maintenance, including

disassembling and reassembling.

This information is DESTINED EXCLUSIVELY for specialised personnel or expert users.

Installation, disassembling and reassembling of the winch by personnel who are not experts may

cause serious damage to users and those in the vicinity of the winch.

Harken®accepts no responsibility for defective installation or reassembly of its winches.

In case of doubt the Harken®Tech Service is at your disposal at techser[email protected]

This Manual is available only in English. If you do not fully understand the English language, do

not carry out the operations described in this Manual.

Technical characteristics

Power ratio Gear ratio

1st speed 20,30 : 1 4,80 : 1

2nd speed 61,00 : 1 14,40 : 1

The theoretical power ratio does not take friction into account.

Weight

ST Version

Weight (Kg) 10,2

Maximum working load

WARNING!

The maximum working load (MWL) for the 60.2 ST Performa™ Winch is 1800Kg (2968 lb)

Subjecting the winch to loads above the maximum working load can cause the winch to fail or

pull off the deck suddenly and unexpectedly during high loads causing severe injury or death.

Outline

246

Ø121

116

Ø236

Line entry height

Performa™Winch 60.2 STP

Installation and Maintenance Manual - Mod.D

Installation

The winch must be installed on a at area of the deck, reinforced if necessary to bear a load equal

to at least twice the maximum working load of the winch.

It is the installer's responsibility to carry out all structural tests needed to ensure that the deck can

bear the load.

Harken®does not supply the screws needed to install the winch since these may vary depending

on the deck on which it is to be installed.

It is the installer's responsibility to choose the correct screws taking account of the loads they will

have to bear.

Harken®assumes no responsibility for incorrect installation of its winches or for an incorrect choice

of mounting screws.

DANGER!

Incorrect installation of the winch may cause severe injury or

death. Consult the yard that built the boat in the case of doubt

over the correct positioning of the winch.

WARNING!

Failure to use the correct number and type of mounting fasteners

or failure to ensure the correct deck strength can result in the

winch pulling off the deck suddenly and unexpectedly during

high loads causing severe injury or death.

WARNING!

Verify the entry angle of the sheet. This must be 8° with tolerance

of ±2°, to avoid sheet overrides and damaging the winch or

making the winch inoperable leading to loss of control of the boat

which can lead to severe injury or death.

WARNING!

Mount the winch on the deck so that the drive gear is positioned

where the sheet enters the winch drum.

Incorrect position of drive gear can weaken winch leading to failure

which can cause an accident leading to severe injury or death.

Once you have chosen the correct mounting position for the winch on the deck proceed with

installation.

Installation

drive gear

SHEET

8°

Performa™Winch 60.2 STP

Installation and Maintenance Manual - Mod.D

Procedure

To install the winch, remove the drum and use Socket Head (SH) bolts or Hexagonal Head (HH)

bolts.

Tools needed

One medium at-bladed screwdriver

To identify the various parts, refer to the exploded view at the end of this Manual.

Torque to apply when assembling

Follow steps below only to install the winch using Socket Head (SH) bolts

1.Unscrew the central screw ( 2Nm/18 in-lb)

3. Unscrew the three screws n°26

(4Nm/35 in-lb)

5. Lift off the drum n°23

2. Slide off the assy socket n°28 and the

cover n°27

4. Remove the stripper arm n°25

by rotating and lifting it.

Install the winch on the deck in the

position you have chosen, keeping in

mind the limits described on page 3.

Performa™Winch 60.2 STP

Installation and Maintenance Manual - Mod.D

Follow steps below only to install the winch using hexagonal headed bolts

Install the winch on the deck in the

position you have chosen, keeping in

mind the limits described on page 3.

6. Completely unscrew the three screws n° 26

8. Slide out the central shaft n°19

10. Remove the assy housing n°16

7. Remove the stripper arm housing n°21

9. Unscrew the 6 hex screws n°17

(20Nm/177 in-lb)

Performa™Winch 60.2 STP

Installation and Maintenance Manual - Mod.D

Installation procedure

Carry out the Procedure, then install the winch on the deck in the chosen position.

A. Position the base of the winch on the deck and mark the position of the holes or use the drilling

cut-out template at the point where you have decided to place the winch.

Below is a reduced scale diagram.

The drilling cut out template is available on the Harken®website, www.harken.com

B. Remove the winch and drill the six 8.5 mm diameter holes.

C. Bolt the base of the winch to the deck using ve M8 bolts (not supplied by Harken®), correctly

chosen for the thickness and type of the boat deck. Consult the yard that built the boat in case of

doubt.

WARNING!

To install the winch on the deck, use only bolts in A4 stainless steel (DIN 267 part11).

Bolts made of other materials may not have sufficient strength or may corrode which can

result in winch pulling off deck suddenly and unexpectedly during high loads causing

severe injury or death.

NOTICE

To mount winches on the deck, do not use countersunk bolts.

D. Fill the mounting holes with a suitable marine sealant.

E. Remove the excess adhesive/sealant from the holes and base drainage channels

final pinion

position

44¡

21¡

55¡

60¡

62¡

60¡

58¡

¯204

¯8.5

n¡6

Winch outside ¯236

Performa™Winch 60.2 STP

Installation and Maintenance Manual - Mod.D

F. Reassemble the winch following the steps of the Procedure in the reverse order, and apply the

products indicated in the section on maintenance.

NOTICE

Before closing the winch, make sure the holes and drainage channels in the base of the winch

are not obstructed.

Positioning the self-tailing arm

Position the self-tailing arm so that the line leaving the winch is led into the cockpit.

Maintenance

Washing

Winches must be washed frequently with fresh water, and in any case after each use.

Do not allow teak cleaning products or other cleaners containing caustic solutions to come into

contact with winches and especially anodised, chrome plated or plastic parts.

Do not use solvents, polishes or abrasive pastes on the logos, on the stickers on the winches or on

any anodized, chrome plated and plastic surfaces.

Make sure that the holes and drainage channels in the base of the winch are not obstructed so that

water does not collect.

Maintenance table

Winches must be visually inspected at the beginning and end of every season of sailing or racing.

In addition they must be completely overhauled, cleaned and lubricated at least every 12 months.

After an inspection, replace worn or damaged components. Do not replace or modify any part of the

winch with a part that is not original.

WARNING!

Periodic maintenance must be carried out regularly. Lack of adequate maintenance shortens

the life of the winch, can cause serious injury and also invalidate the winch warranty.

Installation and maintenance of winches must be carried out exclusively by specialized

personnel.

In the case of doubt contact Harken®Tech Service at techservice@harken.it

Disassembly procedure

Tools needed

One medium at-bladed screwdriver

A number ve hex key

Rags

Torque to be applied in assembly phase

Maintenance

Performa™Winch 60.2 STP

Installation and Maintenance Manual - Mod.D

To identify the various parts refer to the exploded view at the end of this Manual.

Carry out procedure as shown in the paragraph on winch installation and then do the following:

6. Completely unscrew the three screws n° 26

8. Slide out the central shaft n°19

10. Remove the assy housing n°16

7. Remove the stripper arm housing n°21

9. Unscrew the 6 hex screws n°17

(20Nm/177 in-lb)

11. Remove gear n°6, pawls n°3

and washer n°7

Performa™Winch 60.2 STP

Installation and Maintenance Manual - Mod.D

12. Remove gear n°2.

14. Remove roller bearings n°15

16. Remove gear n°10

15. Remove the pawls n°11.

13. Remove the idler and pinion n°14.

17. Remove roller bearings n°12.

Tabla de contenidos

Otros manuales de Cabrestante de Harken

Harken

Harken 70.3 ST EL Manual

Harken

Harken Radial Winch 40.2 PT BBB Manual

Harken

Harken Powered Performa Winch 70.2 STP EL Manual

Harken

Harken 1111 HL Instrucciones de funcionamiento

Harken

Harken 40.2 ST EL Series Manual

Harken

Harken 35.2 PT Manual

Harken

Harken Powered Performa 60.3 STP E Manual

Harken

Harken Performa Winch 70.3 STP Manual

Harken

Harken 46.2 PTBBB Manual

Harken

Harken B 1140 Series Manual de usuario

Harken

Harken PowerSeat PWRS-E Manual de usuario

Harken

Harken Performa Winch 80.2 STP Manual

Harken

Harken Radial Winch 35.2 PT BBB Manual

Harken

Harken HC9565.CLEAR Manual del operador

Harken

Harken 50.2 ST EL/HY Manual

Harken

Harken 16.2 Two Speed Winch Manual

Harken

Harken Carbo AirBlock 340 Manual de usuario

Harken

Harken 53.2ST E/HY Manual de usuario

Harken

Harken Performa Winch 20 STP Manual

Harken

Harken 60.3 ST EL Manual

Harken

Harken 64.2ST E Manual

Harken

Harken Performa Winch 50.2 PTP Manual

Harken

Harken 60.2ST E/HY Manual de usuario

Harken

Harken UniPower Radial Manual

Manuales populares de Cabrestante de otras marcas

WARRIOR

WARRIOR Trojan 40PUS12 Guía de referencia rápida

SVERO

SVERO 16 Manual de usuario

Warrior Winches

Warrior Winches C10000NH Manual de usuario

Badland Winches

Badland Winches 68146 Manual de usuario

Bush

Bush II Series Manual de usuario

Badland

Badland APEX 5500 Manual de usuario

Quadratec

Quadratec Q9000 Synthetic Manual

C-Max

C-Max VIGO Manual de usuario

Comeup

Comeup DV-9 Manual de usuario

Orvea

Orvea Italwinch 805 Manual de usuario

Prowinch

Prowinch PWJTHF300 Manual de usuario

Clas Ohlson

Clas Ohlson LD2000-A Manual de usuario

Topex

Topex 97X080 Manual de usuario

Eastbound

Eastbound MotoWinch 1707001 Manual de usuario

Runva

Runva EWD8000 Guía de referencia rápida

Ingersoll-Rand

Ingersoll-Rand LIFTSTAR FG 1500/CN Series Guía de instalación

Granit

Granit 11157675 Manual de usuario

TREX

TREX TB75 Manual de usuario