Harbor Breeze AR09-52WHT Manual de usuario

OLLINGTON INDOOR

CEILING FAN

HARBOR BREEZE and logo design are

trademarks or registered trademarks of LF,

MODEL # AR09-52WHT AR09-52BLK

AR09-52BN

Español p. 19

Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 888-251-1003, 8 a.m. - 8 p.m., EST, Monday - Sunday. You could

also contact us at [email protected].

ITEM # 5497070 5497071

5497072

AS23223

Safety Information .....................................................................................................

Package Contents .....................................................................................................

Hardware Contents ...................................................................................................

Preparation ................................................................................................................

Initial Installation ........................................................................................................

Fan Mounting ............................................................................................................

Wiring ........................................................................................................................

Final Installation ........................................................................................................

Operating Instructions ...............................................................................................

Care and Maintenance ..............................................................................................

Troubleshooting .........................................................................................................

Limited Lifetime Warranty ..........................................................................................

Replacement Parts List .............................................................................................

TABLE OF CONTENTS

SAFETY INFORMATION

Modifications not approved by the party responsible for compliance could void the user's authority

to operate the equipment.

*NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and receiver.

* Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

The device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, (2) this device must accept any

interference received, including interference that may cause undesired operation.

NOTE: Dimmable to 10% with select dimmers. See lowes.com for more information.

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, install or operate

the product.

SAFETY INFORMATION

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for

repairs, it must be shipped in its original packaging to ensure proper protection against damage

that might exceed the initial cause for return.

• Make sure all electrical connections comply with local codes, ordinances, the National Electrical

Code and ANSI/NFPA 70. Hire a qualified electrician or consult a do-it-yourself wiring handbook

if you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades

to the floor and at least 30 in. from the end of the blades to any obstruction.

• After you install the fan, make sure all connections are secure to prevent the fan from falling.

• The net weight of this fan including the light kit is: 16.94 lbs.

WARNING

To reduce the risk of fire, electrical shock or personal injury, mount to an outlet box

UL-Listed acceptable for fan support of 35 lb. (15.9 kg) or less and use mounting

screws provided with the outlet box. Most outlet boxes commonly used for the

support of lighting fixtures are not acceptable for fan support and may need to be

replaced. Consult a qualified electrician if in doubt.

To reduce the risk of fire, electric shock or personal injury, mount the fan to the outlet box marked

acceptable for fan support with the screws provided with the outlet box.

NEED HELP? In the event you have broken glass or are missing parts, call 888-251-1003. Do

not return the ceiling fan to the place of purchase. Be sure to have available the owner's manual,

item or model number, finish, color, type of glass, etc.

Attention Statement needs to read this way.

ATTENTION: The use of a fan brace with all ceiling fans is recommended. Application style

vary. Braces are sold separately in the lighting or electrical department.

ATTENTION: Do not use an extension cord with this fan.

To reduce the risk of personal injury, use only parts provided with this fan. The use of parts

OTHER than those provided with this fan will void the warranty.

Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to

avoid electrical shock.

SAFETY INFORMATION

CAUTION

To reduce the risk of personal injury, use only the screws provided with the outlet box.

Be sure outlet box is properly grounded and that a ground wire (green or bare) is present.

Before beginning installation, carefully check all screws, bolts and nuts on fan motor assembly

to ensure that they are secured.

WARNING

Risk of Fire and Electric Shock: Do not repair or service this light kit. The light source is

designed for this specific application and can overheat if serviced by untrained personnel. If

any servicing is required, call our customer service department (at 888-251-1003) for return

authorization and shipping instructions.

PACKAGE CONTENTS

IMPORTANT REMINDER: You must use

the parts provided with this fan for proper

installation and safety.

B Canopy 1

Mounting Bracket 1

Canopy Bottom Cover 1

Downrod

E Coupling Cover 1

F Fan motor Assembly 1

G Switch Housing

1H 20W LED Light Kit

DESCRIPTIONPART QUANTITY

J Blade 5

Glass Shade 1

Blade Arm

Pull chain and fob

Cotter Pin (preassembled)

Clevis Pin (preassembled)

Switch Housing Mounting

Screw (preassembled) 3

LED Light Kit Mounting

Screw (preassembled)

Q Balance Kit

DESCRIPTIONPART QUANTITY

Fiber

Blade

Washer

Qty. 15

+ 1 extra

Blade

Screw Blade

Arm

Screw

Qty. 15

+ 1 extra

Qty. 10

+ 1 extra

Wire

Connector

Qty. 4

HARDWARE CONTENTS

PREPARATION

BB CC

AA DD

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and hardware contents list. If any part is missing or damaged, do not attempt to

assemble the product.

Estimated Assembly Time: 120 minutes

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety

Glasses, Stepladder and Wire Strippers.

Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook and

Wire Cutters.

DANGER: When using an existing outlet box, make sure the outlet box is securely attached

to the building structure and can support the full weight of the fan. Failure to do this can result in

serious injury or death. The stability of the outlet box is essential in minimizing wobble and noise

in the fan after installation is complete.

CAUTION: Be sure outlet box is properly grounded and a ground wire (green or bare) is

present.

After opening top of carton, remove mounting hardware package from foam inserts. Remove

motor from packing and place on carpet or on foam to avoid damage to finish.

CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure they

are secured.

INITIAL INSTALLATION

1. Turn off circuit breakers and wall switch to the

fan supply line leads.

2. Determine mounting method to use.

A. Standard mount

B. Angle mount

IMPORTANT: If using the angle mount, ensure

the ceiling angle is not steeper than 19°.

*Helpful Hint: Standard mounting is best suited

for ceilings 7 ft. high or higher. For taller ceilings

you may want to use a longer downrod (not

included). Angle mounting is best suited for

angled or vaulted ceilings. A longer downrod is

sometimes necessary to ensure proper blade

clearance.

3. Check to make sure blades (J) will be at least

30 in. from any obstruction and at least 7 ft.

above the floor.

DANGER: Failure to disconnect power

supply prior to installation may result in

serious injury or death.

OFF

Remove the canopy bottom cover (C) from

the canopy (B) by turning the canopy

bottom cover (C) counterclockwise.

Remove the mounting bracket (A) from the

canopy (B) by loosening canopy mounting

screws a half turn from the screw head.

Next, turn the canopy (B) counterclockwise

to remove the mounting bracket (A) from

the canopy (B).

Secure mounting bracket (A) to outlet box

(not included) using screws, lock washers

and flat washers provided with the outlet

box.

*NOTE: It is very important you use the

proper hardware when installing the

mounting bracket (A) as this will support

the fan.

IMPORTANT: If using the angle mount,

make sure open end of mounting bracket

(A) is installed facing the higher point of the

ceiling.

INITIAL INSTALLATION

Remove the cotter pin (M) and clevis pin

(N), and loosen the two collar set screws

from the fan motor assembly collar.

Flat Washers

Set Screw

Collar

Outlet Box

Screws

Lock Washers

Canopy Mounting

Screw Canopy Mounting

Screw

FAN MOUNTING

Insert downrod (D) through canopy (B),

canopy bottom cover (C) and coupling cover.

Thread wires from fan motor assembly (F)

up through downrod (D).

Slip downrod (D) into collar, align holes and

re-install clevis pin (N) and cotter pin (M).

Tighten set screws in collar.

Carefully lift the fan motor assembly (F) up

to the mounting bracket (A) and seat the

downrod (D) in the mounting bracket (A)

socket. Make sure the tab on the mounting

bracket (A) socket is properly seated in the

groove in the downrod (D). This will help to

balance the ceiling fan.

Set Screw

Slot

Tab

Set Screw

DANGER: Failure to align slot in ball

with tab may cause the fan to wobble or fall,

which could result in serious injury or death.

Collar

BLACK

(WALL

SWITCH)

FAN AND LIGHT CONTROLLED BY TWO WALL SWITCHES

FAN AND LIGHT CONTROLLED BY PULL CHAINS

BLACK (POWER)

WHITE (NEUTRAL)

BLACK

GROUND/GREEN (BARE)

WHITE

120V POWER

FROM CEILING

BLUE &

BLACK

GREEN

WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors

provided with this fan are designed to accept only one 12-gauge house wire and two lead wires

from the fan. If your house wire is larger than 12-gauge or there is more than one house wire to

connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use.

WARNING: If house wires are different colors than referred to in the following steps, stop

immediately. A professional electrician is recommended to determine wiring.

NOTE: This fan is remote control adaptable (remote control not included). If you choose to

purchase a remote control for use with the fan, be advised that the dimming function for the light

will not be operable. Dimming capability for this light is only possible by using wall controls that

control the fan and light separately, such as the WM-7WWL (not included).

CAUTION: Be sure outlet box is properly grounded and a ground (green or bare) wire is present.

WIRING

Choose wiring diagram (Fig. 1A, Fig. 1B or

Fig. 1C) that fits your situation and make

appropriate wiring connections as follows:

[IMPORTANT: For each wire connection

below, use one of the wire connectors (AA),

making sure to screw wire connector (AA)

on in a clockwise direction.]

1A. FAN AND LIGHT CONTROLLED BY

PULL CHAINS: Connect BLACK and BLUE

wire from fan to BLACK wire from ceiling.

Connect WHITE wire from fan to WHITE

wire from ceiling. Connect all GROUND

(GREEN) wires together from fan (on

downrod (D) and mounting bracket (A)) to

BARE/GREEN wire from ceiling.

1B. FAN CONTROLLED BY PULL CHAIN,

LIGHT BY WALL SWITCH: If you intend to

control the fan light with a separate wall

switch, connect BLACK wire from fan to

BLACK wire from ceiling. Connect BLUE

wire from fan to the BLACK wire from the

independent wall switch for the light. Connect

WHITE wire from fan to WHITE wire from

ceiling. Connect all GROUND (GREEN)

wires together from fan (on downrod (D) and

mounting bracket (A)) to BARE/GREEN wire

from ceiling.

FAN AND LIGHT CONTROLLED BY TWO WALL SWITCHES

FAN CONTROLLED BY PULL CHAIN, LIGHT BY WALL SWITCH

BLACK (POWER)

WHITE (NEUTRAL)

BLACK

GROUND/GREEN (BARE)

WHITE

120V POWER

FROM CEILING

BLUE

GREEN

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Admirador de Harbor Breeze

Harbor Breeze

Harbor Breeze Teolo Manual de usuario

Harbor Breeze

Harbor Breeze 00878 Manual de usuario

Harbor Breeze

Harbor Breeze L1901 Manual de usuario

Harbor Breeze

Harbor Breeze 42079 Manual de usuario

Harbor Breeze

Harbor Breeze 00887 Manual de usuario

Harbor Breeze

Harbor Breeze 35063 Manual de usuario

Harbor Breeze

Harbor Breeze CHESHIRE II CSD52FBZ5C4S Manual de usuario

Harbor Breeze

Harbor Breeze 42224 Manual de usuario

Harbor Breeze

Harbor Breeze WAVEPORT STYLE E-WK52NWZ5C1 Manual de usuario

Harbor Breeze

Harbor Breeze TG44LW3D1RS Manual de usuario

Harbor Breeze

Harbor Breeze ELEVATION LP8006LBN Manual de usuario

Harbor Breeze

Harbor Breeze KITSILANO Manual de usuario

Harbor Breeze

Harbor Breeze BOLTZ 42300 Manual de usuario

Harbor Breeze

Harbor Breeze CEDAR HILL Manual de usuario

Harbor Breeze

Harbor Breeze CAF48BNK5L Manual de usuario

Harbor Breeze

Harbor Breeze CHESHIRE II Manual de usuario

Harbor Breeze

Harbor Breeze ARMORY 40087 Manual de usuario

Harbor Breeze

Harbor Breeze BOD52MW3 Manual de usuario

Harbor Breeze

Harbor Breeze LP8072LAZ Manual de usuario

Harbor Breeze

Harbor Breeze Calera Manual de usuario

Harbor Breeze

Harbor Breeze 317058 Manual de usuario

Harbor Breeze

Harbor Breeze BDB52BNK5L Manual de usuario

Harbor Breeze

Harbor Breeze L0982 Manual de usuario

Harbor Breeze

Harbor Breeze 40101 Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje