Harbor Breeze CHESHIRE II Manual de usuario

ITEM #0317058

0317060

MODEL #CE-CSD42AB5C3

CE-CSD42LW5C3

CHESHIRE II CEILING FAN

Français p. 18

Harbor Breeze® is a registered trademark

E124404

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-800-527-1292, 8:30 a.m. - 5 p.m., CST, Monday-Friday.

Federal regulations require ceiling fans with light kits manufactured or imported after

January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore,

this fan is equipped with a wattage limiting device.

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

TABLE OF CONTENTS

Safety Information ........................……………………………………………………….....2 - 3

Package Contents .............................…………………………………………………………..4

Hardware Contents .............................…………………………………………………...........5

Preparation .......................................….…………………..……………………….…..........5

Initial Installation ............................................……………………...………..................6 - 8

Wiring ...............................................................................................……....................8 - 10

Final Installation ............………………….…………...................................................10 - 12

Installing Fan Without Included Light Kit (Optional) ….…............................................

...........

Operation Instructions ..............................................……………………….................13 - 14

Care and Maintenance .......................………………………......………...….....…..............15

Troubleshooting ...........................................………...……………………..….........….15 - 16

Warranty ........................…………………………………….………………..............…......….16

Replacement Parts List .......................………………………......………...….....….............17

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, install or operate the

product. If you have any questions regarding the product, please call customer service at

1-800-527-1292, 8:30 a.m.- 5:00 p.m., CST, Monday - Friday.

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for

repairs, it must be shipped in its original packaging to ensure proper protection against damage that

might exceed the initial cause for return.

• Make sure that all electrical connections comply with local codes, ordinances, the National Electrical

Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring handbook,

available at Lowe's, if you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 feet from the blades to

the floor and at least 30 in. from the end of the blades to any obstruction.

• After you install the fan, make sure that all connections are secure to prevent the fan from falling.

• The net weight of this fan including the light kit is: 12.13 lbs. (5.5 kg).

CAUTIONS

Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid

electrical shock.

Read all instructions and safety information before installing your new fan. Review the

accompanying assembly diagrams.

SAFETY INFORMATION

To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box

marked "ACCEPTABLE FOR FAN SUPPORT" and use mounting screws provided with

the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are

not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in

doubt. Secure the outlet box directly to the building structure. The outlet box and its support must

be able to support the moving weight of the fan (at least 35 lbs.). Do NOT use a plastic outlet box.

To avoid personal injury, the use of gloves may be necessary while handling fan parts with

sharp edges.

To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this

fan are designed to accept only one 12 gauge house wire and two lead wires from the fan. If your

house wire is larger than 12 gauge or there is more than one house wire to connect to the two fan

lead wires, consult an electrician for the proper size wire connectors to use.

To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed

control device or control fan speed with a full range dimmer switch.

To reduce the risk of fire, electrical shock, or personal injury, do not bend the blade arms when

installing them, balancing the blades, or cleaning the fan. Do not insert objects between the

rotating fan blades.

To reduce the risk of personal injury, use only parts provided with this fan. The use of parts

OTHER than those provided with this fan will void the warranty.

This fan MUST be installed with the saftey cable provided with the fan. Failure to use the safety

cable provided may result in personal injury, damage to the fan or damage to other property.

WARNINGS

PACKAGE CONTENTS

IMPORTANT REMINDER: You must

use the parts provided with this fan for

proper installation and safety.

PART DESCRIPTION QUANTITY

L Extra Switch Housing

M Safety Cable

(preassembled)

N Motor Housing Mounting 4

Screw (preassembled)

O Motor Screw 10

(preassembled)

5.4 M/M Lock Washer 10

(preassembled)

Vice (preassembled) 1

PART DESCRIPTION QUANTITY

A Motor Housing 1

B Mounting Bracket 1

C Plastic Lock Tab 1

D Motor Assembly 1

E Light Kit Fitter

F Glass Shade 3

G Blade Arm

H Blade 5

I Candelabra Base Bulb 3

J Pull Chain Extension 2

K Socket Ring

HARDWARE CONTENTS (shown actual size)

Fiber

Blade

Washer

Qty. 15

BB CC

Blade

Screw

Qty. 15 E3 Wire

Connector

Qty. 4

Before beginning assembly and installation of product, make sure all parts are present. Compare

parts with package contents list and hardware contents above. If any part is missing or

damaged, do not attempt to assemble the product. Contact customer service for replacement parts.

Estimated Assembly Time: 120 minutes

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety

Glasses, Stepladder and Wire Strippers

Helpful Tools (not included):AC Tester Light, Tape Measure, Do-It-Yourself-Wiring Handbook

(available at Lowe’s) and Wire Cutters

Bulbs Required (included): 3 candelabra base 60-watt max. bulbs

DANGER: When using an existing outlet box, make sure the outlet box is securely attached to

the building structure and can support the full weight of the fan. Failure to do this can result in serious

injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan

after installation is complete.

CAUTION: Be sure outlet box is properly grounded and that a ground wire (green or bare) is

present.

After opening top of carton, remove mounting hardware package from foam inserts. Remove motor

from packing and place on carpet or on foam to avoid damage to ﬁnish.

CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure that they

are secured.

PREPARATION

INITIAL INSTALLATION

OFF

Turn off circuit breakers and wall switch to the fan

supply line leads. (Fig. 1)

DANGER: Failure to disconnect power supply

prior to installation may result in serious injury or

death.

Check to make sure blades (H) are at least 30 in.

from any obstruction and at least 7 ft. above the

floor. (Fig. 2)

7 ft.

min.

30 in.

min.

Secure mounting bracket (B) to outlet box using

screws, spring washers, and flat washers provided

with the outlet box. (Fig. 3) Pull wires from outlet

box through center hole in mounting bracket (B).

*Note: It is very important that you use the proper

hardware when installing the mounting bracket (B)

as this will support the fan.

Remove motor screws (O) and 5.4 M/M lock

washers (P) from underside of motor and save for

blade arm (G) attachment later on. [If there are

plastic motor blocks installed with motor screws (O)

and 5.4 M/M lock washers (P), discard the plastic

motor blocks.] (Fig. 4)

INITIAL INSTALLATION

Install ball end of motor assembly (D) into

mounting bracket (B) opening. Align slot in ball

with tab in mounting bracket (A). (Fig. 5)

DANGER: Failure to align slot in ball with tab

in mounting bracket (B) may result in serious

injury or death. (Fig. 5)

To ensure the safety of the installation and to

prevent the motor assembly (D) from becoming or

coming loose, use the plastic lock tab (C). Slide

plastic lock tab (C) under bracket tabs so that it will

snap into place. (Fig. 6)

IMPORTANT: Keep in mind that it will require

some force to fully insert the plastic lock tab (C)

so that it does not move or come out once in

the correct position.

NOTE: Make sure that motor assembly (D) does

not swing from side to side too easily--if it does,

check to be sure that the plastic lock tab (C) is

FULLY INSERTED under the bracket tabs and all

the way to the back of the mounting bracket (B).

Wood

Screw

Loop

Nut

Adjust safety cable (M) length by loosening screw

and nut on the safety cable vice (Q) and pulling on

the safety cable (M). Adjust slack in cable to a hands

length and tighten screw and nut on vice (Q)

securely. The loop at the end of the safety cable (M)

should just fit over the threads on the wood screw.

(Fig. 7) Test safety cable (M) by pulling on loose end

with pliers. If the safety cable (M) slips, then vice (Q)

screw and nut must be set tighter.

Hanging

Tab

Ball

Slot

Bracket

Tab

Loop

Wood

Joist

Wood Screw

and Washer

Find a secure attachment point (wood ceiling joist

highly recommended) and secure safety cable

(M). It will be necessary to use a heavy duty

wood screw, washer and lock washer (sold

separately) with the safety cable (M) loop. (Fig. 8)

WIRING

Choose wiring diagram (Fig. 1A, Fig. 1B or Fig. 1C)

that fits your situation and make appropriate wiring

connections as follows: [NOTE: For each wire

connection below, and on the following page, use one

of the wire connectors (CC) provided, making sure to

screw wire connector (CC) on in a clockwise

direction.]

1A. FAN AND LIGHT CONTROLLED BY PULL

CHAINS: Connect BLACK and BLUE wire from fan

to BLACK wire from ceiling. Connect WHITE wire

from fan to WHITE wire from ceiling. Connect

GROUND (GREEN) wire from mounting bracket to

BARE/GREEN wire from ceiling. (Fig. 1A)

FAN AND LIGHT CONTROLLED BY PULL CHAINS

BLACK

WHITE

GROUND/GREEN (BARE)

WHITE

BLUE

WHITE

FROM FAN

120 V Power

FROM

CEILING

FAN

BLACK

GREEN

WARNING: To reduce the risk of fire, electrical

shock, or personal injury, wire connectors provided

with this fan are designed to accept only one 12 gauge

house wire and two lead wires from the fan. If your

house wire is larger than 12 gauge or there is more

than one house wire to connect to the two fan lead

wires, consult an electrician for the proper size wire

connectors to use.

CAUTION: Be sure outlet box is properly grounded

and that a ground (green or bare) wire is present.

WARNING: If house wires are different colors

than referred to in the following steps, stop

immediately. A professional electrician is

recommended to determine wiring.

INITIAL INSTALLATION

WIRING

1B. FAN CONTROLLED BY PULL CHAIN, LIGHT

BY WALL SWITCH: If you intend to control the fan

light with a separate wall switch, connect BLACK

wire from fan to BLACK wire from ceiling. Connect

BLUE wire from fan to the BLACK wire from the

independent wall switch for the light. Connect

WHITE wire from fan to WHITE wire from ceiling.

Connect GROUND (GREEN) wire from mounting

bracket to BARE/GREEN wire from ceiling. (Fig. 1B)

FAN CONTROLLED BY PULL CHAIN, LIGHT BY

WALL SWITCH

WHITE

BLACK

BLACK (WALL SWITCH)

GROUND/GREEN (BARE)

BLACK

BLUE

WHITE

FROM FAN

FAN

120 V Power

FROM

CEILING

WHITE

GREEN

Wrap electrical tape around each individual wire

connector (CC) down to the wire as shown in Fig. 2.

WARNING: Make sure no bare wire or wire

strands are visible after making connections. Place

green and white connections on opposite side of box

from the black and blue (if applicable) connections.

Turn spliced/taped wires upward and gently push

wires and wire connectors (CC) into outlet box.

CC E3 Wire Connector x4

Hardware Used

1C. FAN AND LIGHT CONTROLLED BY TWO

WALL SWITCHES: If you intend to control the fan

and light with separate wall switches, connect

BLACK wire from fan to BLACK wire from the

independent wall switch for the fan. Connect BLUE

wire from fan to the BLACK wire from the other

independent wall switch for the light. Connect WHITE

wire from fan to WHITE wire from ceiling. Connect

GROUND (GREEN) wire from mounting bracket to

BARE/GREEN wire from ceiling. (Fig. 1C)

Note: Black wire is hot power for fan. Blue wire is hot

power for light kit. White wire is common for fan and

light kit. Green or bare wire is ground.

WHITE

BLACK (WALL SWITCH)

BLACK (WALL SWITCH FOR LIGHT)

GROUND/GREEN (BARE)

BLACK

BLUE

WHITE

FROM FAN

FAN

120 V Power

FROM

CEILING

FAN AND LIGHT CONTROLLED BY TWO WALL

SWITCHES

WHITE

GREEN

WIRING

IMPORTANT: Using a full range dimmer switch to

control fan speed will cause a loud humming noise

from fan. To reduce the risk of fire or electrical

shock, do NOT use a full range dimmer switch to

control fan speed. (Fig. 3)

Dimmer

Switch Speed

Switch

For illustrative purposes only--not

intended to cover all types of controls

FINAL INSTALLATION

Temporarily raise motor housing (A) to mounting

bracket (B) to determine which two motor housing

mounting screws (N) align with slotted holes in motor

housing (A) and partially loosen these two motor

housing mounting screws (N). Remove the other two

motor housing mounting screws (N). Now, lift motor

housing (A) to mounting bracket (B) again, aligning

slotted holes in motor housing (A) with loosened

motor housing mounting screws (N) in mounting

bracket (B). Twist motor housing (A) to lock. Re-insert

motor housing mounting screws (N) that were

previously removed. Tighten all four motor housing

mounting screws (N) securely. (Fig. 1)

Partially insert three blade screws (AA), along with

three fiber blade washers (BB), to attach one blade

arm (G) to a blade (H). Then, tighten each blade

screw (AA), starting with the one in the middle (Fig. 2)

Repeat with remaining blades (H).

AA Blade Screw x15

Hardware Used

BB Fiber Blade Washer x15

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Admirador de Harbor Breeze

Harbor Breeze

Harbor Breeze ARMORY 40087 Manual de usuario

Harbor Breeze

Harbor Breeze LAKE PLACIDO CPK1261 Manual de usuario

Harbor Breeze

Harbor Breeze 35062 Manual de usuario

Harbor Breeze

Harbor Breeze 80202 Manual de usuario

Harbor Breeze

Harbor Breeze LARALYN LRN32 Manual de usuario

Harbor Breeze

Harbor Breeze 40016 Manual de usuario

Harbor Breeze

Harbor Breeze TALAMORE TAL60MBK8LR Manual de usuario

Harbor Breeze

Harbor Breeze BDB52ABZC5P Manual de usuario

Harbor Breeze

Harbor Breeze HTE21091 Manual de usuario

Harbor Breeze

Harbor Breeze 40662 Manual de usuario

Harbor Breeze

Harbor Breeze MARINA COVE II Manual de usuario

Harbor Breeze

Harbor Breeze FREEPORT LP8079LAZ Manual de usuario

Harbor Breeze

Harbor Breeze SARATOGA 00798 Manual de usuario

Harbor Breeze

Harbor Breeze 41182 Manual de usuario

Harbor Breeze

Harbor Breeze 40678 Manual de usuario

Harbor Breeze

Harbor Breeze LP8221LCH Manual de usuario

Harbor Breeze

Harbor Breeze E-TM52BNK5LED Manual de usuario

Harbor Breeze

Harbor Breeze 00880 Manual de usuario

Harbor Breeze

Harbor Breeze EUK60MBK10LR Manual de usuario

Harbor Breeze

Harbor Breeze Bath Ventilator with Light Manual de usuario

Harbor Breeze

Harbor Breeze LP8115LAZ Manual de usuario

Harbor Breeze

Harbor Breeze E-WCK44ABZ5LKS Manual de usuario

Harbor Breeze

Harbor Breeze ANIVA BAY Manual de usuario

Harbor Breeze

Harbor Breeze PLM52CB5D Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje