Hans Grohe Metris Select 320 1jet Series Manual

ZH 用户手册/组装说明 2

EN Instructions for use / Assembly instructions 3

Lesezeichen

中文 2

English 3

Metris Select 320 1jet

14883007

中文

安装 (参见第页4)

安全技巧

装配时为避免挤压和切割受伤，必须戴上手套。

冷热水管间过大的压力差必须予以平衡。

安装提示

• 安装前必须检查产品是否受到运输损害。安装后将不认可运输损害或

表面损伤。

• 管道和阀门必须根据通用标准进行安装、冲洗和检查。

• 请遵守当地国家现行的安装规定。

• 首次调试时和维护作业之后，管接头中的空气可能产生噪音。大约使

用管接头15次后噪音消失。

技术参数

工作压强： 最大1MPa

推荐工作压强： 0,1-0,5MPa

测试压强： 1,6MPa

(1MPa=10bar=147PSI)

热水温度： 最大60°C

热力消毒:70°C/4分钟

• 该产品专为饮用水设计！

• 自动防止回流

符号说明

请勿使用含有乙酸的硅胶！

调节 (参见第页6)

热水温度调节。如果使用即热式喷头，则不建议安装热水阀门。

保养 (参见第页9)

单向阀必须在符合国家或当地的法律的情况下按照EN806-5定期检查(至

少一年一次)。

大小 (参见第页8)

流量示意图 (参见第页8)

备用零件 (参见第页10)

清洗 (参见第页7)

操作 (参见第页6)

• 汉斯格雅建议，清晨或在水流长时间停滞后，前半升水不作饮用水使

用。

• 通过手柄打开阀门时出水口可能流出少量水。

• 抬起把手打开龙头，并调节需要的水温。通过位于正面出水口的调节

钮可以暂时停止水流。长时间不使用时，例如夜晚或房屋空置，则必

须将把手完全关闭。

问题原因补救

没有水 - 回流截止阀杵杆(A)未安装 - 安装杵杆(A)(参见第页32/36)

龙头不灵活 - 阀芯损坏，结垢 - 更换阀芯

龙头滴水 - 阀芯损坏 - 更换阀芯

水从龙头出水嘴流出 - O形环损坏 - 更换O形环

水从螺纹底座中流出 - 连接软管没有完全旋入基体 - 用手拧紧连接软管

- 连接软管的O形环损坏 - 更换O形环

热水温度过低 - 温度限制器设置错误 - 设置温度限制器

更换龙头后，在打开可调龙头时流量减少 - 安装了错误的可调龙头 - 更换可调龙头(#98463000)

调节按钮不好用 - 调节按钮脏污 - 清洁调节按钮，给O形环23x1,5上油

(参见第页10)

English

Assembly (see page 4)

Safety Notes

Gloves should be worn during installation to prevent crushing and cutting

injuries.

The hot and cold supplies must be of equal pressures.

Installation Instructions

• Prior to installation, inspect the product for transport damages. After it has been

installed, no transport or surface damage will be honoured.

• The pipes and the ﬁxture must be installed, ﬂushed and tested as per the

applicable standards.

• The plumbing codes applicable in the respective countries must be observed.

• During initial start-up and after servicing, air in the ﬁttings can cause noise. After

switching the jet on and oﬀ about 15 times, the noise will stop.

Technical Data

Operating pressure: max. 1 MPa

Recommended operating pressure: 0,1 - 0,5 MPa

Test pressure: 1,6 MPa

(1 MPa = 10 bar = 147 PSI)

Hot water temperature: max. 60°C

Thermal disinfection: 70°C / 4 min

• The product is exclusively designed for drinking water!

• Safety against backﬂow

Symbol description

Do not use silicone containing acetic acid!

Adjustment (see page 6)

To adjust the hot water limiter. Using a hot water limiter in combination with a

continuous ﬂow water heater is not recommended.

Maintenance (see page 9)

The check valves must be checked regularly according to EN 806-5 in accord-

ance with national or regional regulations (at least once a year).

Dimensions (see page 8)

Flow diagram (see page 8)

Spare parts (see page 10)

Cleaning (see page 7)

Operation (see page 6)

• Hansgrohe recommends not to use as drinking water the ﬁrst half liter of water

drawn in the morning or after a prolonged period of non-use.

• Minor leaking may occur brieﬂy at the spout when opening the ﬁtting via the

lever.

• Use the lever to open the tap and set the desired temperature. The water ﬂow

can be paused by pressing the Select button on the face side of the spout.

When the tap is not used for a longer period of time, f.e. when retiring at night

or leaving the house, it must be closed completely by means of the lever.

Fault Cause Remedy

No water - No plunger (A) for the backﬂow preventer was

installed

- Install plunger (A) (see page 32 / 36)

Mixer stiﬀ - Cartridge defective, calciﬁed - Exchange cartridge

Mixer dripping - Cartridge defective - Exchange cartridge

Water escaping in area of swivel spout - O-ring defective - Exchange O-ring

Water escaping at the threaded base - connection hoses not completely screwed into basic

body

- Tighten connection hoses by hand

- O-ring at the connection hose defective. - Exchange O-ring

Hot water temperature too low - Hot water limiter incorrectly set - Set hot water limiter

Low ﬂow with Select valve after valve replacement - Improper Select valve installed - Replace Select valve (#98463000)

Select button stiﬀ - Select button soiled - Clean Select button and grease 23x1,5 O-ring

(see page 10)

(3 Nm)

max. 35 mm

max. 60 mm

1a 21b

150°

110°

TX20

4 5a

SW 24 mm

(4 Nm)

SW 10 mm

SW 19 mm

(4Nm)

75°

55°

95°

55°

95°

360°

150°

TX20

(2 Nm)

(A)

MontageMontage

> 2 min

360°

55°

35°

75°

35°

SW 22 mm

110°

TX20

(2 Nm)

SW 22 mm

(2 Nm)

7 8 9

Montage

0,3 MPa

60 °C 10 °C

21 3 4

5 6 7

6 x

36°C

38°C

43°C

50°C

55°C

60°C

17 x

4 mm

(5 Nm)

4 mm

关 / close

开 / open 热 / hot

冷 / cold

开 / open

关 / close

Justierung / Bedienung

English

Cleaning Recommendation for Hansgrohe Products

Today, modern sanitary and kitchen tapware, showers, accessories, washstands,

tubs and radiators consist of very diﬀerent materials to comply with the needs of the

market with regard to design and functionality.

To avoid damage and reclamations, it is necessary to consider cer

tain criteria when

cleaning.

With regard to caring for the Hansgrohe products, the fol-

lowing must in principle be heeded:

• Only use cleaning material which is explicitly provided for this type of applica-

tion.

• Never use cleaning materials, which contain hydrochloric acid, formic acid,

chlorine pale lye or acetic acid, as they cause considerable damage.

• Phosphorus acidic cleaners are only conditionally applicable.

• Mixing cleaning agents is not permitted, generally.

• Never use cleaning materials or appliances with an abrasive eﬀect, such as

unsuitable cleaning powders, sponge pads or micro ﬁbre cloths.

• The instructions of the cleaning agent manufacturers have to be followed

absolutely.

• Cleaning has to be carried out with a speciﬁed cleaner dosage, contact time,

object-related and adapted to the needs.

• The building up of calciﬁcations has to be removed by cleaning regulary.

• When using spray cleaners, spray the cleaning solution onto a soft cloth or

sponge, never directly onto the Hansgrohe products, as the atomised spray

could enter openings and gaps in the Hansgrohe products and cause damage.

• After cleaning rinse thoroughly with clean water to remove any cleaner residue.

• The use of steam cleaners is not permitted. The high temperatures can damage

the products.

Important

Residues of toiletries such as liquid soaps, shampoos and shower gels, hair dyes,

perfumes, aftershave and nail varnish can also cause damage.

Here too: Carefully rinse with water after use to remove residues.

Likewise, do not store any cleaning agents or chemicals under the products, for

example in a vanity unit, as the vapours may damage the products.

The damage of already damaged surfaces will deteriorate under the eﬀect of the

cleansers.

Components with damaged surfaces must be exchanged,

otherwise there could be an injury danger.

Damage caused by improper treatment will not be covered by our guarantee.

Warranty

Hansgrohe guarantees to the consumer that this product is free of production faults.

If evertheless any defect is detected within 5 years from date of purchase, Hans-

grohe will remedy this defect free of charge. You will ﬁnd the conditions and details

of this guarantee at www.hansgrohe-int.com/guarantee. Please contact your

contracting party to claim your rights under this guarantee. This guarantee does not

aﬀect the customer‘s rights under the respective national legislation.

QuickClean

The QuickClean cleaning function only needs a small manual rub over to remove

the lime scale from the spray channels.

•

Hansgr

ohe

Hansgrohe

ww.hansgrohe-int.com/guarantee

uickClean

QuickClean

QUICK

CLEAN

Reinigung

223

13°

307

257

365

183

163

110

157

Ø 34

max. 60

183

835

G 3/8

208

121

365

G 3/8

G 1/2

bar

4,5

0,0

0,5

1,0

1,5

2,0

2,5

3,0

3,5

4,0

5,0

0,45

0,00

0,05

0,10

0,15

0,20

0,25

0,30

0,35

0,40

0,50

5,50,55

6,00,60

036912151821242730

MPa

00,1 0,2 0,3 0,4 0,5

Q = l/min

Q = l/sec

Metris Select 320 1jet

14883007

Metris Select 320 1jet

14883007

Maße / Durchﬂussdiagramm

SW 10 mm SW 19 mm

12 3

SW 10 mm

SW 19 mm

(4 Nm)

Wartung

98462000 92287000

(23x1,5)

92289000

95140000

97523000

96456000

95291000

95372000

97548000

92481000

(11x3)

92961000

92730000

95008000

97209000 98455000

96338000

95049000

98189000

(14x2,5)

97558000

92646000

98368000

98193000

(32x2)

95498000

92288007

98486000

(110° / 150°)

Armaturenfett

Grease

䀵滑油

93395000

(G⅜ / G½)

Metris Select 320 1jet

14883007

Serviceteile

Otros manuales para Metris Select 320 1jet Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Producto de plomería de Hans Grohe

Hans Grohe

Hans Grohe PuraVida 15472 Series Manual de usuario

Hans Grohe

Hans Grohe Focus 31940000 Manual

Hans Grohe

Hans Grohe 27409 Series Manual

Hans Grohe

Hans Grohe Finoris 260 76070 Series Manual

Hans Grohe

Hans Grohe Allegro N 71844 1 Series Manual de instrucciones

Hans Grohe

Hans Grohe Axor Starck Organic 12171001 Manual de instrucciones

Hans Grohe

Hans Grohe Raindance Select 2jet Showerpipe 27126000 Manual

Hans Grohe

Hans Grohe PuraVida Manual de usuario

Hans Grohe

Hans Grohe Logis 71315 Series Manual

Hans Grohe

Hans Grohe Montreux Wall Shower Mixer 16560XX1 Manual del propietario

Hans Grohe

Hans Grohe Metropol Series Manual

Hans Grohe

Hans Grohe 13904000 Manual de usuario

Hans Grohe

Hans Grohe Croma Showerpipe 27201000 Manual de usuario

Hans Grohe

Hans Grohe Logis 210 71131 Series Manual

Hans Grohe

Hans Grohe RainButton iBox Control 01600180 Manual

Hans Grohe

Hans Grohe Ecostat 04353000 Manual de instrucciones

Hans Grohe

Hans Grohe AXOR Starck 10635 Series Manual de usuario

Hans Grohe

Hans Grohe Talis M52 170 2jet 32841000 Manual

Hans Grohe

Hans Grohe Metropol 14463 Series Manual de usuario

Hans Grohe

Hans Grohe Talis S 200 72813251 Guía

Hans Grohe

Hans Grohe AXOR Citterio 39136 1 Series Manual de instrucciones

Hans Grohe

Hans Grohe PuraVida 15270 Series Manual

Hans Grohe

Hans Grohe AXOR Carlton 17454XX1 Guía de instalación

Hans Grohe

Hans Grohe Zesis M33 150 1jet 74806 Series Manual de usuario

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

Kohler

Kohler K-6228 Instrucciones de montaje

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

American Standard

American Standard DetectLink 6072121 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Kohler

Kohler K-12183 Instrucciones de montaje

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Kohler

Kohler Centerset K-15240 Instrucciones de montaje

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

baliv

baliv WT-140 Manual de usuario

Kohler

Kohler Mira Eco Manual de operación