Hans Grohe II Guía de instalación

Showerpanel I

Showerpanel II

Installation Instructions / Warranty

Showerpanel I

Showerpanel II

Showerpanel I Showerpanel II

handshower & bodyjets handshower, bodyjets, tub spout

Metro E 06572000 06573000

Solaris E 06549XX0 06550XX0

Stratos E 06564XX0 06565XX0

Technical information Données techniques

Recommended water pressure Pression d’eau recommandée 45 - 72.5 psi

Max. water pressure Pression d’eau maximum 147 psi

Recommended hot water temp. Température recommandée d'eau

chaude 120� - 140� F*

Max. hot water temp Température maximum d'eau

chaude 158�F*

Flow rate of handshower Débit de douchette 2.5 gpm

Flow rate of each bodyspray Débit de chaque jet mural <1.0 gpm

Flow rate of thermostatic mixing

valve Débit maximum du mitigeur ther-

mostatique 8 gpm @ 45 psi

10 gpm @ 65 psi

*Please know and follow all applicable local plumbing codes when setting the temperature on the water heater.

* Vous devez connaître et respecter tous les codes de plomberie locaux applicables pour le réglage de la température

du chauffe-eau.

Installation considerations

English

Check package contents

Before beginning installation, check the contents of this package. Make sure that all parts

are present and in good condition. If any part is missing or damaged, please contact

Hansgrohe Customer Service before proceeding.

Tools required

The following tools are suggested for installing the showerpanel:

Tape measure

Level

Grease pencil or other marking device

Drill with 6 mm bit suitable for wall

surface

10 mm nut driver

10, 11 and 19 mm wrenches

•

3 mm Allen wrench

Philips screwdriver

Waterproof sealant

Mallet (to install anchors)

Teflon tape

•

Français – voir p. 17

For best results, Hansgrohe recom-

mends that this unit be installed by a

licensed, professional plumber.

Please read over these instructions

thoroughly before beginning installa-

tion. Make sure that you have all tools

and supplies needed to complete the

installation.

This product is listed by IAPMO and is

approved for use in Massachusetts.

•

Protection against backflow provided

by check valve in the handshower

outlet.

The high temperature limit stop on the

thermostatic mixing valve may be reset

to comply with local plumbing codes*

-- see page 13.

•

*In Massachusetts, the maximum output temperature

cannot exceed 112°F.

Rough-in

Installation on a flat wall Installation in 90° corner

Seal the wall around the

nipples with waterproof

sealant.

Failure to seal the wall

can lead to possible water

damage.

English

This unit can be installed on a flat wall or

in a 90° corner. Instructions for installa-

tion on a flat wall begin on page 5. Go

to page 8 if the panel is to be installed in

a corner.

Ensure that you have a minimum

83" ceiling height from the stand-

ing surface.

Stub out 1/2" NPT male nipples for the

hot and cold water supplies at the loca-

tions shown on the appropriate rough-in

diagram. The nipples should extend 5/8"

outside the surface of the finished wall.

Install the wall surface and make the wall

watertight before installing the panel. The

panel hangs on the finished wall.

Installation � flat wall

Wrap the threads on the nipples with Teflon tape.

Install the elbows so that the outlets face upwards.

Measure up the wall 78 ¾", making sure that the line is

plumb. Mark the position for the top screw hole.

From the position of the top screw hole, measure down

35 3/8”. Mark the position for the center screw hole.

From the center screw hole, measure down 19 1/8".

Mark the position for the bottom screw hole.

Use a 6 mm bit to drill the three screw holes.

Install the set screws in the top and bottom holes.

Use a 10 mm nut driver to attach a nut to the top set

screw.

Slide the panel over the top and bottom set screws.

Tighten the nut on the top set screw.

Install and tighten the nut on the bottom set screw.

Install one recessed head screw and the large washer

on the center hole. Tighten the screw.

Seal the wall around the anchors

with waterproof sealant.

Failure to seal the wall can lead to

possible water damage.

English

Use the compression nuts and ferrules to connect

the supply hoses on the panel to the supply

elbows.

Use two wrenches, as shown, to prevent the sup-

ply hoses from twisting.

Attach the seals to the side covers.

Install the side covers.

The pins on the covers must go into the grooves on

the sides of the panel.

English

Push the bodyjet supply hose on the valve cover into the fitting on the panel.

Install the valve cover on the panel.

The pins on the cover must connect to the slots on the panel.

Turn to page 11 to continue the installation.

English

Installation in 90° corner

Wrap the threads on the nipples with Teflon tape.

Install the elbows so that the outlets face upwards.

In the corner, measure up the wall 78 ¾", making

sure that the line is plumb. Mark the position for the

top mounting bracket.

From the position of the top screw hole, measure

down 35 3/8". Mark the position for the center

mounting bracket.

From the center screw hole, measure down 19 1/8".

Mark the position for the bottom mounting bracket.

Use the mounting brackets as templates to mark the

positions of the screw holes. Drill the holes with a 6

mm bit.

Install the corner sealing gasket to the grooves on

the panel.

Seal the wall around the anchors

with waterproof sealant.

Failure to seal the wall can lead to

possible water damage.

Install the mounting brackets to the walls using five of

the recessed head screws.

English

While a helper holds the panel, attach the supply

hoses to the elbows with the compression fittings.

Use two wrenches, as shown in the diagram, to

prevent the supply hoses from twisting.

Tighten the hex head cap screw on the top

mounting bracket.

Install and tighten the hex head cap screw on the

bottom mounting bracket through the hole in the

panel and tighten.

Install the hex head cap screw and large washer

on the center mounting bracket through the hole

in the panel and tighten.

English

Clip the side cover seals as shown in the diagram. Attach the side cover seals to the valve

cover.

Push the bodyjet supply hose on the

valve cover into the fitting on the

panel.

Install the valve cover on the panel. The pins on the cover

must connect to the slots on the panel.

Turn to page 11 to continue the installation.

English

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Producto de plomería de Hans Grohe

Hans Grohe

Hans Grohe Allegro E 14801XX1 Manual de usuario

Hans Grohe

Hans Grohe RainBrain 15840180 Manual de usuario

Hans Grohe

Hans Grohe Tecturis E 80 CoolStart 73001 Series Manual

Hans Grohe

Hans Grohe Rainfinity 250 1jet 26226 Series Manual

Hans Grohe

Hans Grohe AXOR Starck 40871000 Manual

Hans Grohe

Hans Grohe Raindance 2625418 Series Manual

Hans Grohe

Hans Grohe Metris S 31063821 Manual de usuario

Hans Grohe

Hans Grohe AXOR Citterio 39455 Series Manual de usuario

Hans Grohe

Hans Grohe iBox 13595000 Manual de usuario

Hans Grohe

Hans Grohe Flowstar 52105 Series Manual de usuario

Hans Grohe

Hans Grohe Axor Starch 28491000 Manual de usuario

Hans Grohe

Hans Grohe AXOR Starck 10920000 Manual

Hans Grohe

Hans Grohe AXOR Massaud 18950000 Manual

Hans Grohe

Hans Grohe Logis M31 160 1jet 71833000 Manual

Hans Grohe

Hans Grohe Axor 39134000 Manual

Hans Grohe

Hans Grohe Decor 70 31733 Series Manual de usuario

Hans Grohe

Hans Grohe Metris Select M71 200 2jet 73819 Series Manual

Hans Grohe

Hans Grohe ShowerTablet Select 700 13183 Series Manual

Hans Grohe

Hans Grohe Metropol 32543 Series Manual de usuario

Hans Grohe

Hans Grohe Croma Showerpipe 220 27185 1 Series Manual de instrucciones

Hans Grohe

Hans Grohe Logis E 71232000 Manual

Hans Grohe

Hans Grohe Raindance Select Showerpipe 27286000 Manual

Hans Grohe

Hans Grohe Focus 31930000 Manual

Hans Grohe

Hans Grohe Talis S 31515000 Manual

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

Kohler

Kohler K-6228 Instrucciones de montaje

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

American Standard

American Standard DetectLink 6072121 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Kohler

Kohler K-12183 Instrucciones de montaje

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Kohler

Kohler Centerset K-15240 Instrucciones de montaje

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

baliv

baliv WT-140 Manual de usuario

Kohler

Kohler Mira Eco Manual de operación