Hans Grohe Ecostat 1001 SL Care 13284000 Manual de usuario

Installation Instructions

Ecostat 1001 SL Care

13282000

Ecostat 1001 SL Care

13284000

Contents

Safety and Important Information 3

Pack Contents 4

Dimensions 4

Technical Data 5

Supply Conditions TMV2 5

Supply Conditions TMV3 5

Installation Requirements 6-7

Installation

Thermostat 8-

Commissioning and in-service tests

Commissioning 9

In-service tests 10

Frequency of in-service tests 10

Thermostatic Adjustement

Temperature Limitation 11

Operating your Shower 12

Cleaning 13

Spare Parts 14-15

Trouble Shooting 16

The Ecostat 1001 SL Care 13284000 meets

the requirements of the TMV2 Scheme.

The Ecostat 1001 SL Care 13282000 meets the

requirements of the TMV2 and TMV3 Scheme.

If there are any queries regarding this product or its

installation, please contact the Hansgrohe technical

hotline: 0870 7701975

Safety and Important Information

Hansgrohe products are safe provided they are installed, used and maintained in accordance with these

instructions and recornrnendations.

Please read these instructions thoroughly and retain for future use.

The plumbing installation of this shower must comply with the requirements of UK

Water Regulations/Bylaws (Scotland), Building Regulations or any other regulations specified by the local

Water Authority and supplier.

We strongly recommend that you use a plumber registered with or a member of an Association:

Institute of Plumbing (IOP) - throughout the UK

National Association of Plumbing, Heating and Mechanical Services Contractors

(NAPH & MSC) - England & Wales

Water Industry Approved Plumber Scheme (WIAPS)

Dispose of plastic bags carefully

Keep children well away from the work area.

Check for hidden pipes and cables in the wall before drilling holes.

The unit must be mounted on a finished waterproofed wall surface (usually tiles).

If you are using power tools (e.g. to drill holes) wear safety glasses and always disconnect tools from the

power supply after use.

Do not operate the shower unit if the hand shower or spray hose has been damaged or is blocked.

Do not block the flow of water from the hand shower, by placing it on your hand or any other part of your

body or foreign object.

The thermostatic unit should be serviced annually by a qualified person to ensure maximum safety during

use.

The mixer incorporates check valves (page 14 pos. 4) and filters (page 14 pos 7).

The fitting of isolation valves is required (preferred location page 6 and 7 Installation Requirements)

Dimensions

Pack Contents

Please check that you have been supplied with the

following:

Ecostat 1001 SL Care 13282000

1 Ecostat 1001 SL 3 Escutcheons

2 Mesh washers 4 S-unions

Ecostat 1001 SL Care 13282000

Ecostat 1001 SL Care 13284000

1 Ecostat 1001 SL 3 Escutcheons

2 Mesh washers 4 S-unions

Ecostat 1001 SL Care 13284000

Technical Data

Ecostat 1001 SL Care

This thermostatic valve will suit supplies of:

HIGH PRESSURE (HP-S)

Operating pressure: max. 10 bar

Recommended operating pressure: 0.2 - 5 bar

Test pressure: 16 bar

Hot water temperature: max. 80°C

Recommended hot water temp.: 65°C

Rate of flow from bath spout: 20 l/min. @ 3 bar

Rate of flow from shower outlet:18 l/min. @ 3 bar

Maximum outlet temperature: 43°C +/-*

Safety check: 40°C

Hot water connection: Left hand

Cold water connection: Right hand

Minimum difference between hot

water and mixed water temperature: 6 K

Hot and cold supply pressure should be balanced

Operating pressure range High pressure Low pressure

Maximum static pressure - bar 10 10

Flow pressure, hot and cold - bar 1 to 5 0.2 to 1

Hot supply temperature - °C 52 to 65 52 to 65

Cold supply temperature - °C 5 to 20 5 to 20

Mixed water temperature

Application Mixed water temperature

(at point of discharge)

Bidet 38°C max.

Shower 41°C max.

Washbasin 41°C max.

Bath (44°C fill) 44°C max.

Bath (46°C fill) 46°C max.

* For preset outlet temperature adjustment – See

page 9 „Commisioning“.

NB. If a water supply is fed by gravity then the

supply pressure should be verified to ensure the

conditions of use are appropriate for the valve.

Valves operating outside of these supply conditions

cannot be guaranteed to operate as a TMV2 or

TMV3 valve.

Supply Conditions TMV2

Supply Conditions TMV3

Operating pressure range High pressure Low pressure

Maximum static pressure - bar 10 10

Flow pressure, hot and cold - bar 1 to 5 0.2 to 1

Hot supply temperature - °C 55 to 65 55 to 65

Cold supply temperature - °C 5 to 25 5 to 25

The following models are TMV3 approved for high

pressure shower (HP-S) application: 13282000

Installation Requirements

This thermostatic mixer valve must be installed

in compliance with current Water Regulations. If

you have any doubts about the Water Regulation

requirements contact your local water services

provider or use the services of a professional

plumber.

This mixer valve is suitable for use with the following

water supply systems:

Gravity Fed Hot and Cold (pressure balanced) 0.1 - 1.0 bar

Gas Combination Boiler (multi-point) 1.0 - 10 bar*

Unvented System (pressure balanced) 1.0 - 10 bar

Pumped System 1.0 - 10 bar

IMPORTANT: If you install this mixer with a

gravity fed system, there must be a minimum head

(vertical distance) from the underside of tlie cold

water storage tank to the showerhead position of

at least 1 metre.

Before connecting the mixer, water should be flushed

through the system to remove all debris that might

otherwise damage the valve.

* If pressure is in excess of 3.5 bar, a pressure-

reducing valve should be fitted.

KEY

Isolating valve

Reducing valve

Mixer Valve

Pump

Gravity Fed Hot and Cold (pressure balanced)

Gas Combination Boiler (multi-point)

Unvented System (pressure balanced)

Pumped System

32 - 41

Seal

Shower Thermostat

PTFE

tape

150 mm

HOT

COLD

Shower Thermostat

1. The hot and cold water outlets should be 150mm

apart (plus or minus 12mm). Hot on the left and

cold on the right (fig. 1). The recommended

plumbing fittings are “ back plate elbows (not

supplied).

2. Flush through the hot and cold water supplies.

3. Wrap PTFE tape round the S-unions and screw

into the backplate elbows. The S-unions must

protrude beyond the tiled surface between 32

and 41mm (figs.2-3).

4. Seal the gap between the S-unions and the tiles

(fig.3).

5. Screw the escutcheons onto the S-unions.

6. Fasten the thermostatic mixer onto the S-unions

using the union nuts. Align the unit and tighten

the nuts (be careful not to damage the chrome

finish). The S-unions allow inaccuracies to be

compensated for.

Installation

Bath/Shower Thermostat

As the shower thermostat above (positioned over

a bath).

Commissioning and in-service

tests

Commissioning

Purpose

Since the installed supply conditions are likely to

be different from those applied in the laboratory

tests it is appropriate, at commissioning, to carry

out some simple checks and tests on each mixing

valve to provide a performance reference point for

future in-service tests.

Procedure

1. Check that:

a) the designation of the thermostatic mixing

valve matches the intended application

b) the supply pressures are within the range of

operating pressures for the designation of

the valve

c) the supply temperatures are within the range

permitted for the valve and by guidance

information on the prevention of legionella

etc.

2. Adjust the temperature of the mixed water in

accordance with the manufacturer’s instructions

and the requirement of the application and then

carry out the following sequence:

a) record the temperature of the hot and cold

water supplies

b) record the temperature of the mixed water

at the largest draw-off flow rate

c) record the temperature of the mixed water

at a smaller draw-off flow rate, which shall

be measured

d) isolate the cold water supply to the

mixing valve and monitor the mixed water

temperature

e) record the maximum temperature achieved

as a result of (d) and the final stabilised

temperature

NOTE: The final stabilised mixed water

temperature should not exceed the values in

Table A.

Application Mixed water

temperature

Shower 43°C

Washbasin 43°C

Bath (44°C fill) 46°C

Bath (46°C fill) 48°C

f) record the equipment, thermometer etc. used

for the measurements

Table A: Guide to maximum stabilised

temperatures recorded during site

tests

In-service tests

Purpose

The purpose of in-service tests is to regularly monitor

and record the performance of the thermostatic

mixing valve. Deterioration in performance can

indicate the need for service work on the valve and

/ or the water supplies.

Procedure

1. Carry out the procedure 2. (a) to (c) on page

10 using the same measuring equipment, or

equipment to the same specifications.

2. If the mixed water temperature has changed

significantly from the previous test results (e.g. >

1 K), record the change and before re-adjusting

the mixed water temperature check:

a) that any in-line or integral strainers are

clean

b) any in-line or integral check valves or other

anti-backsiphonage devices are in good

working order

c) any isolating valves are fully open

3. With an acceptable mixed water temperature,

complete the procedure 2. (a) to (c) on page 9.

4. If at step 2. (e) on page 10 the final mixed water

temperature is greater than the values in Table

A and / or the maximum temperature exceeds

the corresponding value from the previous test

results by more than about 2 K, the need for

service work is indicated.

NOTE: In-service tests should be carried out with

a frequency which identifies a need for service

work before an unsafe water temperature can

result. In the absence of any other instruction

or guidance, the procedure described in

„Frequency of in-service tests“ may be used.

Frequency of in-service tests

TMV3*

General

In the absence of any other instruction or guidance on

the means of determining the appropriate frequency

of in-service testing, the following procedure may

be used:

1. 6 to 8 weeks after commissioning carry out the

tests given in 2. on page 9.

2. 12 to 15 weeks after commissioning carry out

the tests given in 2. on page 9.

3. Depending on the results of 1. and 4. several

possibilities exist:

a) If no significant changes (e.g. < 1 K) in

mixed water temperatures are recorded

between commissioning and 1., or between

commissioning and 4. the next in-service test

can be deferred to 24 to 28 weeks after

commissioning.

b) If small changes (e.g. 1 to 2 K) in mixed

water temperatures are recorded in only one

of these periods, necessitating adjustment of

the mixed water temperature, then the next

in-service test can be deferred to 24 to 28

weeks after commissioning.

c) If small changes (e.g. 1 to 2 K) in mixed

water temperatures are recorded in both of

these periods, necessitating adjustment of

the mixed water temperature, then the next

in-service test should be carried out at 18 to

21 weeks after commissioning.

d) If significant changes (e.g. > 2 K) in mixed

water temperatures are recorded in either

of these periods, necessitating service work,

then the next in-service test should be carried

out at 18 to 21 weeks after commissioning.

4. The general principle to be observed after the first

2 or 3 in-service tests is that the intervals of future

tests should be set to those which previous tests

have shown can be achieved with no more than

a small change in mixed water temperature.

*TMV2: The frequency of performing the in-service

tests is 1 year maximum.

Otros manuales para Ecostat 1001 SL Care 13284000

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Producto de plomería de Hans Grohe

Hans Grohe

Hans Grohe Talis S 200 72813251 Guía

Hans Grohe

Hans Grohe Accessories E & S 40518XX0 Manual de usuario

Hans Grohe

Hans Grohe Rainfinity 130 3jet 26864 Series Manual de usuario

Hans Grohe

Hans Grohe Talis S 72425009 Manual

Hans Grohe

Hans Grohe Rainfinity 250 1jet 26226 Series Manual

Hans Grohe

Hans Grohe Unica'E Series Manual de instrucciones

Hans Grohe

Hans Grohe Axor Citterio M 100 1jet Air 34610000 Manual de usuario

Hans Grohe

Hans Grohe Unica'C Series Manual

Hans Grohe

Hans Grohe Verso 220 Showerpipe 27290000 Manual

Hans Grohe

Hans Grohe Rebris S 72530 1 Series Guía

Hans Grohe

Hans Grohe Ecostat Square 15714000 Manual de usuario

Hans Grohe

Hans Grohe iBox 13595000 Manual de usuario

Hans Grohe

Hans Grohe AXOR Uno 27985 Series Manual de usuario

Hans Grohe

Hans Grohe 31741180 Manual

Hans Grohe

Hans Grohe Massaud 18471180 Manual de usuario

Hans Grohe

Hans Grohe Ecostat Universal Series Manual

Hans Grohe

Hans Grohe Trio 15932000 Manual

Hans Grohe

Hans Grohe Ecostat 1001 SL Care 13284000 Manual

Hans Grohe

Hans Grohe Focus M42 150 1jet 71814 Series Manual

Hans Grohe

Hans Grohe Porter'E 28387 Series Manual de usuario

Hans Grohe

Hans Grohe Raindance Connect 27164 1 Series Manual de usuario

Hans Grohe

Hans Grohe Crometta Vario 9 l/min 26332340 Manual de usuario

Hans Grohe

Hans Grohe Showerpanel Guía de instalación

Hans Grohe

Hans Grohe Croma Showerpipe 27159000 Manual de usuario

Manuales populares de Producto de plomería de otras marcas

Weka

Weka 506.2020.00E Instrucciones de funcionamiento

Kohler

Kohler K-6228 Instrucciones de montaje

UBERHAUS DESIGN

UBERHAUS DESIGN 75175017 Manual de usuario

American Standard

American Standard DetectLink 6072121 Manual de usuario

Uponor

Uponor Contec TS Manual de usuario

Pfister

Pfister Selia 49-SL Manual de usuario

Fortis

Fortis VITRINA 6068700 Manual de usuario

Fortis

Fortis MILANO 78211JS Manual de usuario

Kohler

Kohler K-12183 Instrucciones de montaje

Maxxus

Maxxus MX-M206-01 Manual de usuario

Moen

Moen 5922 Series Manual de usuario

Viega

Viega Prevista Pure 8512 Manual de usuario

Kohler

Kohler Centerset K-15240 Instrucciones de montaje

Viega

Viega Prevista Dry 8522.33 Manual de usuario

Sanela

Sanela Lema SLP 59RB Manual de usuario

Elkay

Elkay EDF15AC Manual de instalación

baliv

baliv WT-140 Manual de usuario

Kohler

Kohler Mira Eco Manual de operación