Hangar 9 VRTF Easy 2 Manual de usuario

INSTRUCTION MANUAL

WE GET PEOPLE FLYING

• Assembles in two easy hours

• Only requires one tool to build — and it’s included!

• No glue is required to assemble (no smell, no mess)

• Modular construction allows for easily replaced parts if crash damaged

• Can be disassembled in approximately 15 minutes for easy storage/transportation

• Pre-covered and trimmed in genuine UltraCote™

• All balsa plywood craftsmanship constructed

Table of Contents

Introduction 3

Additional Parts Needed 3

Radio System Set-Up 4

Easy 2 Parts Layout 4

Airplane Orientation 4

Stage 1 — Assembling the Wing 5

Stage 2 — Installing the Radio 9

Stage 3 — Installing the Linkages 13

Stage 4 — Installing the Tail 16

Stage 5 — Installing the Landing Gear 19

Stage 6 — Installing the Engine 21

Installing the Propeller 23

Installing the Antenna 23

Balancing the Easy 2 24

Pre-Flight Check 25

Flight Instructions 26

Pre-Flight at the Field 27

AMA Safety Code 28

Glossary 29

Congratulations on your purchase of Hangar 9’s Easy 2™, the first in Hangar 9’s VRTF™series of airplanes.

VRTF, Virtually Ready-to-Fly, is a concept that Hangar 9 pioneered. Unlike standard ARF (Almost Ready-to-Fly)

airplanes that typically take up to 20 hours to build, the Easy 2 can be assembled in just two easy hours.

Furthermore, the Easy 2 doesn’t require glue, and only one tool is needed for the complete assembly

process—and that tool, a Phillips screwdriver, is even included.

For first-time fliers, the Easy 2 is the perfect trainer with positive self-righting flight characteristics and

exceptional slow flight performance. More experienced flyers will find the Easy 2 to be a quick way to get in the

air fast with a high-quality, all-wood UltraCote™covered airplane that even the most discriminating pilot would

be proud to show off.

The Easy 2 includes both a written instruction manual and a Real-Time™instruction video. If feasible, we highly

recommend using the video instructions and keeping the written instructions handy for reference or for

clarifying any questions you may have regarding any of the assembly steps.

While the Easy 2 can easily be built in two hours using the video instructions, there’s certainly no rush. If you’d

prefer to spend a couple of evenings assembling a stage, or perhaps doing two stages per night, please feel

free to do so. On the average for most, the actual assembly time using the video instructions takes just under

two hours, while assembling using only the written instructions may take slightly longer.

There is a glossary located at the back of this manual should you encounter any unfamiliar terms.

Additional Parts Needed to Assemble the Easy 2:

• .40 –.46 2-cycle engine with muffler

• 4-channel or greater radio system with four standard servos (JR F400 with four 507 servos recommended)

• Aileron extension (Part JRPA112)

Helpful Additional Items (Optional):

• Masking tape

• Pen

Additional Items Needed to Get the Easy 2 in the Air:

• Propeller (10 x 6 if using a .40 size engine)

• Hangar 9 field kit, which includes: glow plugs, fuel pump, 4-way wrench, glow plug igniter with charger,

chicken stick and tote box (Part HANSTART)

• Fuel (Omega or Cool Power 10% – 15% nitro content recommended)

Introduction

Radio System Set-Up

It’s a good idea to begin charging the radio system first, so that later, in Stage 3, you’re able to center the

servos. Locate your charger and plug your battery pack and transmitter into your charger. Plug the charger into

an outlet to begin charging.

Easy 2 Parts Layout

Airplane Orientation

The left and right of the airplane refers to the left and right side as if you were stationed in the cockpit.

Antenna Tube

Fuselage (HAN1801) Rubber Bands Wing Joiner Rods (HAN1806) Spinner

Wing

Dowels

Aileron

Linkages

Nose Wheel

Assembly

Pushrods

Nose Wheel

Control Horn

Phillips

Screwdriver

Main Gear

(HAN1804)

Wing Kit

(HAN1802)

Shock Loc™

Radio Tray

(HAN1807)

Tail Assembly

(HAN1803)

Stage 1 — Assembling the Wing

• Wing halves (left and right)

• Steel wing rods (2)

• One servo with mounting hardware (4 rubber grommets,

4 eyelets and 4 long servo screws — included with the

radio system)

• Aileron linkages with clevis attached (2) — these are the

shortest two linkages in the kit

• Small self-tapping screws (2)

• Small rubber bands (3)

• Aileron connectors (2) Note: On some Easy 2 kits,

these may already to attached to the aileron torque rods.

Parts Needed

Steel Wing

Rods

Aileron

Linkages

Left Wing

Half

Right Wing

Half Mounting

Hardware Servo

Aileron

Connectors

Small

Self-Tapping

Screws

Small

Rubberbands

Note: After completion of the instructional video and

manual, the white clevises were substituted with the

high-quality Dubro #669 Black Clevises.

Step 1. From your radio system box, remove one servo and the

servo mounting hardware — four rubber grommets, four brass

eyelets and four servo screws. Prepare the servo by installing

the four rubber grommets and eyelets in one servo as shown in

the photo. The grommets insert onto the servo tabs and then the

eyelets are inserted from the bottom through the grommets.

The grommet installation is fairly simple. However, if you need

any additional help for this installation, please refer to your

radio system instruction manual.

Step 2. Note there is a rectangular shaped cut-out on the

bottom of the right wing panel (the panel with the Easy 2 decal).

Install the servo prepared in Step One into the cut-out in the

wing, as shown, with the servo arm nearest the front (leading

edge) of the wing.

Note: The wire (servo lead) should exit on the side as shown.

To fasten the servo in place, use the four self-tapping servo

screws included with your radio and the screwdriver included in

the Easy 2 kit. Tighten just until they compress the rubber

grommets slightly.

Note: Do not “smash” down the rubber grommets; tighten

just until the grommets compress slightly.

Step 3. Insert the two steel wing rods into the right wing half as

shown in the photo. Push them in as far as they will go.

CONTINUED

Stage 1 — Assembling the Wing

Slide the left and right wing halves together, making sure the

alignment pin near the trailing edge correctly engages in the hole.

Step 4. Two screws will be installed on the bottom of the wing,

one in each wing panel, with the heads slightly raised. Three

rubber bands will then be looped around the screws to hold the

wing halves together.

To install the screws, make sure they thread into the narrow

hardwood strip inside the wing by measuring with the 79/16

template provided at right on this page. Approximately 1/2

(about a finger’s width) from the center joint of the wing, screw

in the small self-tapping screws (one on each wing half) about

half way.

Note: The screws will start to thread in easily, then become

more difficult to turn as the screw enters the hardwood

wing spar.

Now loop the three small rubber bands several times around the

screws to hold the wing halves together. Note: The package

contains more rubber bands; however only three are used here.

Note: The pattern of the looping of these rubber bands

makes no difference. Some use a figure 8 shape,

others just use an oval shape. What is important is

that the rubber bands are securely attached to hold

the wing halves together.

Step 5. For your convenience, the aileron torque rod

connectors are already installed on the torque rods of the wing.

If the connectors are not installed, screw the aileron connectors

onto the threaded rods (called aileron torque rods), which are

protruding from the wing. Screw the connector until the rod is

flush with the top of the aileron connector.

CONTINUED

Stage 1 — Assembling the Wing Screw

location

Trailing

edge of

wing

7-9/16"

Step 6. Install the Z-bend of one of the aileron linkages into the

outermost hole in the aileron servo arm as shown.

Note: It may fit tightly and be necessary to work the Z-bend

back and forth until it inserts freely.

Helpful Hint: To make it easer to insert the Z-bend into the

servo horn,loc-

ate one of the

screws that later

will be used to

secure the

Shock-Loc™

radio tray. Screw

it into the hole in

the servo horn

three turns,

where the pushrod wire Z-bend will be inserted, and

then back it out. This will make installing the Z-bend

much easier.

Now install the other aileron linkage on the opposite side using

the same procedure as above. Once installed, move the linkages

back and forth a few times until they move freely.

When both aileron linkages are attached, center the servo so the

servo arm is parallel to the wing’s leading and trailing edge.

Step 7. We will now be fitting the clevis into the aileron

connectors on the torque rods. At this point, it may be necessary

to adjust the length of the aileron linkage so the ailerons are

aligned with the trailing edge of the wing surface. To adjust the

length of the aileron linkage, simply turn the plastic clevis in or

out until, when connected, the aileron is level with the wing.

Note: If the aileron is lower than the trailing edge, the

linkage needs to be shortened and vice versa.

Congratulations — you have just completed the wing!

Stage 1 — Assembling the Wing

CONTINUED

Step 8. Prepare your servos by installing the rubber grommets

on the three remaining servos, four on each.

Note: Do not install the brass eyelets. The Shock-Loc radio

tray is designed to capture the servos by the rubber

grommets and the eyelets are not needed.

Hint: It’s helpful to mark the servo wires so they can easily be

identified when it’s time to install them in the receiver. A

piece of masking tape near the connector with the

appropriate letter (T=throttle, E=elevator, R=rudder)

written on it will save time later during the radio hook up.

• Fuselage with pushrods and tank pre-installed

• Shock-Loc radio tray with six self-tapping screws

•

Three servos with rubber grommets (12). Note: The eyelets

and servo screws included with the radio will not be used

• Receiver (included with the radio system)

• Battery pack (included with the radio system)

• Switch harness (included with the radio system)

• Aileron extension (additional part required)

• Medium rubber bands (2)

• Double-sided servo tape (2 pieces)

• Masking tape (optional)

• Pen (optional)

Stage 2 — Installing the Radio

Parts Needed

Rubber

Bands

Shock-Loc

Radio Tray Receiver Battery

Pack Double-Sided

Servo Tape Switch

Harness

Rubber

Grommets

Aileron

Extension

Step 9. Install the servos in the fuselage as shown. First install

the elevator and rudder servos and then the throttle servo,

feeding the servo leads in first toward the front of the airplane,

and then placing in the servo.

Important: Refer to the photo to note which servo goes in

which position.

Important: Note the position of the servo arms.

Step 10. Peel back one side of a piece of double-sided tape and

attach the tape to the bottom of the receiver. Attach the other piece

of the double-sided tape to the battery pack. Now peel off the

opposite sides of the double-sided tape and stick the battery and

receiver centered on opposite sides of the Shock-Loc radio tray in

the position shown. (The receiver goes centered on one side of

the tray while the battery pack goes centered on the other.)

Note: The receiver servo slots need to be positioned such

that they’re on the end of the tray, facing away from

the servo openings.

Now, using the two medium rubber bands, wrap the bands

around the receiver and battery pack to secure them in place.

Each rubber band makes a complete revolution around the two

and attaches to the side notches on the Shock-Loc radio tray.

Elevator

Throttle Rudder

Stage 2 — Installing the Radio

CONTINUED

Bottom

Top

Tabla de contenidos

Otros manuales de Juguete de Hangar 9

Hangar 9

Hangar 9 P-51D Mustang 40 ARF Manual de usuario

Hangar 9

Hangar 9 Spitfire Mk.IX ARF Manual de usuario

Hangar 9

Hangar 9 EDGE 540 Manual de usuario

Hangar 9

Hangar 9 T-34 Mentor 40 ARF Manual de usuario

Hangar 9

Hangar 9 PULSE XT 40 ARF Manual de usuario

Hangar 9

Hangar 9 Timber 110 30-50cc Manual de usuario

Hangar 9

Hangar 9 Alpha 40 ARF Manual de usuario

Hangar 9

Hangar 9 33% Pawnee 80cc ARF Manual de usuario

Hangar 9

Hangar 9 HAN1300 Manual de usuario

Hangar 9

Hangar 9 Hangar 9 P-51 Mustang ARF Manual de usuario

Hangar 9

Hangar 9 Hangar 9 P-51 Mustang ARF Manual de usuario

Hangar 9

Hangar 9 P-47D Thunderbolt 20cc Manual de usuario

Hangar 9

Hangar 9 P-47 thunderbolt Manual de usuario

Hangar 9

Hangar 9 85cc Sukhoi SU-26MM Manual de usuario

Hangar 9

Hangar 9 FuntanaS 90 Manual de usuario

Hangar 9

Hangar 9 Ultra Stick 40 ARF Manual de usuario

Hangar 9

Hangar 9 YAK 54 89 Manual de usuario

Hangar 9

Hangar 9 40-Size Floats Manual de usuario

Hangar 9

Hangar 9 frenzy 100 Manual de usuario

Hangar 9

Hangar 9 P-51D Mustang 40 ARF Manual de usuario

Hangar 9

Hangar 9 Twin Otter ARF Manual de usuario

Hangar 9

Hangar 9 Ultra Stick 10cc Manual de usuario

Hangar 9

Hangar 9 fokker D.VII Manual de usuario

Hangar 9

Hangar 9 J-3 Piper Cub Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario