Hangar 9 Spitfire Mk.IX ARF Manual de usuario

Spitfire Mk.IX ARF

SAFETY PRECAUTIONS

INSTRUCTION MANUAL

First-time builders should seek advice from people having building

experience.If misused or abused,it can cause serious bodily injury

and damage to property.

Fly only in open areas and preferably at a dedicated R/C flying site.

We suggest having a qualified instructor carefully inspect your

airplane before its first flight.Please carefully read and follow all

instructions included with this airplane,your radio control system

and any other components purchased separately.

(The people under 18 years old is forbidden from flying this model)

This R/C airplane is not a toy!

Specication:

Wing Span: 2058mm/81in

Length: 1715mm/67.5in

Flying Weight: ~7.6kg

Wing area: 74.95 dm2

Engine: 35cc-40cc

R/C System: 2.4Ghz 6ch

Servo: GP *7 ; EP * 6

Battery: LI-PO 5S*2 5000mAh 30C

ESC: 120A High voltage Brushless ESC

Electric retract system

Receiver

7.4V 30C

For retracts

4.8V

For receiver

In order to let the customers have

more choices, we don't provide a

uniform plugs.

4. Assemble the electric retracts to the plane

after several times smoothly running.

Please don't ceaselessly turn and off the switch in 2 seconds,

if you do this way, the circuit board will be heated.

Thank you very much for purchasing our TRCM optional electric retract set,

all our products were passed strict QC before they shipped out to the customers.

In order to avoid probably trouble happen, we still would like you to follow the steps

below before you assemble our electric retracts to your plane.

1. Connecting the circuit board to the battery and receiver.

2. Turn on the radio control to check the lights

on the circuit board, if the lights turn on green

or turn on red orderly，0.5 second after each

from the right to the left and all the lights will

turn off after 15 seconds, then the circuit will

work normally. Otherwise the circuit will be a

defective one if you make sure the setting on

your radio control are correct, please don't use

it but contact with your supplier in time.

3. Link the electric retract units to the

circuit boards after the above two

steps, check again the electric retracts

to see if they can work normally or not.

35cc gas engine

Engine 19″X10

Motor 21″X12

6 channel radio for aiplane is highly recommended for this model.

9Optional electric retract set

We strongly recommen you use the thread lock for all the screws when you build your model.

4.25 in scale spinner

Motor: Outer rotor, 63-60 220KV

Gasoline tube

Gasoline

Accessories packing list

TP Screw (3x20mm )

TP Screw (2.3x8mm)

Tail wheel (45mm)

Main wheels (100mm)

Copper joiner

Linkage Stopper 2

Plastic tube (2x650mm)

Fuel tank (550cc) 1

Steel wire (0.5x3000mm)

pivot & round hinge(5x68mm)

Screw (6x50mm)

Gear door

Pin hinge(24x24mm)

TP Screw (2.3x12mm)

Horn(2mm) 6

Horn(2mm) 2

Clevis

Screw (2x10mm)

Washer(2x5mm)

Servo tray(2mm)

Push rod

(2x115mm)

Purchased separately

Wooden Block

Circlip

Retracts strut

circuit board

Oleo struts

Screw (2.6x12mm) 5

Washer(3x10mm)

EVA(10mm)

Screw (3x10mm)

Washer(3x6mm)

Fiber deconations

scoop

Antenna

Screw (3x20mm)

Scale gun set

Canopy Fiberglass

Canopy PVC

carbon ber tube(10x285mm)

Aluminum tube

Push rod

(2x70mm)

Main wing joiner(20x420mm)

Push rod

Tail gear

Alu clevis

Locknut (2mm )

Wooden Block

(20x20x8mm)

Scale gun set

Assemble the canopy to the cockpit with screws.

Assemble the cockpit to the fuselage.

Assemble the scale gun set to the wing and the ber

scoop to the fuselage.

1.5mm

TP Screw (2.3x8mm)

Blind Nut

Screw (3x20mm)

200mm

253mm

Epoxy the ber deconations to aprropriate position

on the bottom of the wing.

The centre of the Gravity.

The skech map of the Spitre plane install

completion.

130 mm

scoop

Servo tray(68.5x56.5x2mm)

Securely glue together. If coming o during ights, you 'll

lose control of your airplane which leads to accidents!

Make sure hinges are

mounted in the same line.

Pivot & round hinge(5x68mm)

Clevis（2mm)

Screw (2x10mm)

Locknut (2mm )

Push rod

（2mm)

Washer(2x5mm)

Horn 2

1mm

Aileron

Trailing

edge

Cut away the rubber tube when

the epoxy glue dried.

Make sure they are in

the right position while

installing.

Pivot & round hinge(5x68mm)

Horn(2mm)

Rod (2x300mm)

Ball joint

Washer(2x5mm)

Screw (2x10mm)

Nut (2mm )

Wooden Block

(20x20x8mm)

Ball joint

Lock Nut (2mm )

Washer(2x5mm)

Screw (2x10mm)

Install the servo as the illustration below.

Install the nylon control horn and connect the linkage.

Apply instant AB glue to aileron and pin hinge.

Assemble the aileron to main wing with instant type AB glue. Be careful

to ensure the moving parts of the hinges are able to move freely.

Keep some space about 1mm width between the

trailing edge and the aileron.

Accessory list for the coming installation steps.

Securely glue together. If coming o during ights, you 'll

lose control of your airplane which leads to accidents!

Flap

1mm

Make sure they are in

the right position while

installing.

Trailing

edge

TP Screw (2.3x12mm) 8

1.5mm

Pin hinge(24x24mm)

Masking tape

Servo tray(68.5x56.5x2mm)

Clevis（2mm)

Screw (2x10mm)

Locknut (2mm )

Washer(2x5mm)

Horn 2

Pin hinge(24x24mm)

Push rod

（2mm)

TP Screw (2.3x12mm)

Wooden Block

(20x20x8mm)

Assemble the servo tray to the wing with screws

and epoxy the ber horn to the aileron.

Epoxy the pin hinges to the slots in the ap.

Epoxy the aps to the wings as illustration.

Keep some space about 1mm width between

trailing edge and ap.

Accessory list for the coming installation steps.

Fiber deconations

scoop

Antenna

Cut o the surplus part from the PVC canopy, glue the berglass

pic to the PVC canopy and trim o the surplus part.

Fiberglass

PVC

Fiberglass

Screw (3x20mm)

Scale gun set

Mount the fuel tank, battery and receiver to

the fuselage.

Assemble the antenna to the fuselage with screw.

TP Screw (2.3x8mm)

Canopy (Fiberglass)

Canopy (PVC)

Fuel supply line

Fuel spray line

Air pressure line

Assembly of the fuel tank(please notice that the plug of

the tank and the tube should special for gasoline.

Screw (3x20mm)

Antenna

56 58

Accessory list for the coming installation steps.

Screw

Using scotch tape, one side of it xed, cover the blind nut hole and mark

where the blind nut holes are.put the cowl to it is place on the fuselage,

base on the marks on the scoth tape drill holes to the cowling.

Install the engine to the engine mount with screws.

Screw (3x10mm)

Washer(3x6mm)

3mm

49 52

Assemble the servo tray to the wing with screws and

epoxy the ber horn to the ap.

Main wing joiner(20x420mm) 8

TP Screw (2.3x12mm)

Gear door

TP Screw (3x20mm)

Retracts strut

Wooden Block

Note:rubber wheels oleo struts

and retracts are optional.

Circlip

stainless steel rod

Wooden Block

Circlip

Retracts strut

circuit board

Oleo struts

TP Screw (2.3x12mm)

1.5mm

Screw (6x50mm)

Masking tape

Main wheels (100mm)

Mount the gear door and the wheel to the retract.

Horn(2mm)

Rod (2x300mm)

Ball joint

Washer(2x5mm)

Screw (2x10mm)

Nut (2mm )

Ball joint

Lock Nut (2mm )

Washer(2x5mm)

Screw (2x10mm)

Install the servo as the illustration below.

Install the nylon control horn and connect the linkage.

Accessory list for the coming installation steps.

Main wing joiner(20x420mm)

TP Screw (3x20mm)

TP Screw (3x20mm) 8

TP Screw (2.3x12mm)

Assemble the retracts to the appropriate position

in the gear house.

Connect the two wings through the main wing joiners.

The sketch map of the wing ts well to the fuselage.

Drag the servo line and retracts lines from the wing.

Main wing joiner(20x420mm)

Factory already set blind nuts in the wings, the customers can

x the wing to the fuselage by tightening the nylon screws.

Screw (6x50mm)

AA'

Make sure to glue securely.

If not properly glued, a failure in ight may occur.

Temporarily fasten down the main wing and

check its correct position.

Securely glue together.If coming o during ights,

you'll lose control of your airplane which leads

to accidents!

A=A'

B=B'

The sketch map should be when the stabilizer

assembly completion.

16 19

Linkage Stopper 2

Plastic tube (2x650mm)

Fuel tank (550cc) 1

Screw (3x10mm)

Washer(3x6mm)

Tail wheel servo

Rudder servo

TP Screw (2.3x8mm)

1.5mm

TP Screw (2.3x8mm)

163mm

The sketch map of the steel wires working in

the fuselage.

The sketch map of the steel wires connection out

of the fuselage.

Take o the tail wheel and trim a slot on the tail

cover for assembling the tail wheel. The side view when the engine install completion.

Assemble the tail gear cover with screws as below.

Accessory list for the coming installation steps.

Tail wheel (45mm)

Collar

Screw (2.6x12mm) 3

Screw (2.6x12mm)

Steel wire (0.5x3000mm)

Steel wire

Copper joiner

Lock Nut (2mm )

Screw (2x10mm)

Ball joint

Washer(2x5mm)

Steel wire

Copper joiner

Lock Nut (2mm )

Screw (2x10mm)

Ball joint

Washer(2x5mm)

Aluminum tube

Install the servo.

Clevis

Copper joiner

Screw (2x10mm)

Washer(2x5mm)

Steel wire (0.5x3000mm)

Aluminum tube

Clevis

Copper joiner

Screw (2x10mm)

Washer(2x5mm)

Steel wire (0.5x3000mm)

Aluminum tube

Alu clevis Locknut (2mm )

Locknut (2mm )

The sketch map when assemble the tail landing

gear to the wheel steeling mount.

The sketch map of the tail wheel and steel wires

working in the fuselage.

Fix the tail gear to the tail fuselage.

Assemble the steel wires well to the rudder horn

and tail wheel.

Connect the steel wires of the rudder horn and

tail gear to the servo.

carbon ber tube(10x285mm)

1mm

Tailing

edge

Cut away the rubber tube when

the epoxy glue dried.

Make sure they are in

the right position while

installing.

Elevator

Apply instant type AB glue to elevator and hinges.

Keep some space about 1mm width between

elevator and tailing edge.

Securely glue together. If coming o during ights, you 'll

lose control of your airplane which leads to accidents!

Epoxy the elevator to the stabilizer.

Fix the carbon ber tube to one side of the stab

with screws.

Glue the wooden block to each side of the stab tube as below, put the stab

tube into one side the horizontal to the end and mark it out at the root of

the horizontal, drill a hole in the stab tube and horizontal as illustration.

Make sure hinges are

mounted in the same line.

5mm 5mm

15mm 15mm

1.5mm

Screw (2.6x12mm) 1

Washer(3x10mm)

3mm

Screw (2.6x12mm)

Washer(3x10mm)

Screw (2.6x12mm) 2

Washer(3x10mm)

carbon ber tube(10x285mm)

Horn 4

pivot & round hinge(5x68mm)

Accessory list for the coming installation steps.

AA'

Make sure to glue securely.

If not properly glued, a failure in ight may occur.

Temporarily fasten down the main wing and

check its correct position.

Securely glue together.If coming o during ights,

you'll lose control of your airplane which leads

to accidents!

A=A'

B=B'

Screw (2.6x12mm)

Washer(3x10mm)

1.5mm

Screw (2.6x12mm) 1

Washer(3x10mm)

3mm

Make sure hinges are

mounted in the same line.

Securely glue together. If coming o during ights, you 'll

lose control of your airplane which leads to accidents!

Horn 4

pivot & round hinge(5x68mm)

The sketch map should be when the stabilizer

assembly completion.

Assemble the stab to the fuselage drill a hole to

the other section stab.

Fix the other side of the stab with screw.

Epoxy the pivot & round hinges to the rudder.

Epoxy the rudder to the vertical n.

Epoxy the ber horns to the slots in the rudder

and elevator.

Clevis(2mm)

Lock Nut (2mm )

Screw (2x10mm) Washer(2x5mm)

Screw (2x10mm)

Washer(2x5mm)

EVA(10mm)

Assemble the servos.

The sketch map of the push rod connect to the

elevator servo.

Assemble the push rod branches to the horns on

the elevator.

Assemble the another side of the push rod to the

elevator servo in the fuselage as image.

The sketch map of the push rod working in the fuselage.

Linkage Stopper

Washer (2mm)

Nut (2mm)

Set screw (3x4mm)

Steel wire (0.5x3000mm)

Copper joiner

Screw (2x10mm)

Washer(2x5mm)

Push rod

Set screw (3x4mm)

Washer (

2mm

)

Nut (2mm)

Aluminum tube

Linkage Stopper 1

TP Screw (2.6x12mm )

TP Screw (2.3x8mm)

Tail wheel (45mm)

Tail gear

Alu clevis

2mm Rod

Adjustable Rod

Lock Nut (2mm )

Screw (2x10mm)

Washer(2x5mm)

Push rod

Locknut (2mm )

Accessory list for the coming installation steps.

Tabla de contenidos

Otros manuales de Juguete de Hangar 9

Hangar 9

Hangar 9 Hangar 9 P-51 Mustang ARF Manual de usuario

Hangar 9

Hangar 9 Inverza 33 Manual de usuario

Hangar 9

Hangar 9 HAN2990 Manual de usuario

Hangar 9

Hangar 9 Hangar 9 P-51 Mustang ARF Manual de usuario

Hangar 9

Hangar 9 Extra 300 ARF Manual de usuario

Hangar 9

Hangar 9 fokker D.VII Manual de usuario

Hangar 9

Hangar 9 PT-19 Manual de usuario

Hangar 9

Hangar 9 P-40B Warhawk 50 ARF Manual de usuario

Hangar 9

Hangar 9 Alpha 40 Manual de usuario

Hangar 9

Hangar 9 FuntanaS .40 Manual de usuario

Hangar 9

Hangar 9 Sukhoi SU-31 Manual de usuario

Hangar 9

Hangar 9 Taylorcraft 26cc Hangar 9 Manual de usuario

Hangar 9

Hangar 9 Piper Cherokee Manual de usuario

Hangar 9

Hangar 9 F4U-1A Corsair 20cc Manual de usuario

Hangar 9

Hangar 9 P-47D Thunderbolt 20cc Manual de usuario

Hangar 9

Hangar 9 HAN Extra 330SC 60e Manual de usuario

Hangar 9

Hangar 9 Twist 60 ARF Manual de usuario

Hangar 9

Hangar 9 85cc Sukhoi SU-26MM Manual de usuario

Hangar 9

Hangar 9 P-40 Warhawk Manual de usuario

Hangar 9

Hangar 9 ULTRA aspire Manual de usuario

Hangar 9

Hangar 9 1/5 Spitfire Mk IXc 30cc Manual de usuario

Hangar 9

Hangar 9 Pulse XT 60 ARF Manual de usuario

Hangar 9

Hangar 9 Advance 40 Manual de usuario

Hangar 9

Hangar 9 Clipped Wing Taylorcraft ARF Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario