Haier HLP141E Manual de usuario
.
User Manual
Model HLP141E, HLP140E
Guide de l’Utilisateur
Modéle HLP141E, HLP140E
Manual del Usuario
Para Modelo de HLP141E, HLP140E
Electric Vented Tumble Dryer
Sécheuse Électrique Ventilée
Secadora eléctrica de ropa con
ventilación
3
Grounding Instructions:
This appliance must be grounded. It is equipped with a 3-wire cord having
a grounded plug. The plug must be plugged into an outlet which is properly
installed and grounded
Warning – Improper use of the grounded wire can result in the risk of electric
shock. Consult a qualified electrician if necessary. Do not attempt to defeat this
safety feature by modifying the plug. Avoid the use of an extension cord because
it may overheat and cause a risk of fire. However, if it is necessary to use an
extension cord:
A. Use only 3-wire extension cord with 3-blade grounding plug.
B. The marked rating of the extension cord must be equal to or greater than the
rating of this appliance.
Attempting any maintenance or cleaning:
To minimize the possibility of electric shock, unplug this appliance from the power
supply or disconnect the dryer at the household distribution panel by removing
the fuse or switching off the circuit breaker before attempting any maintenance or
cleaning (except the removal and cleaning of the lint filter).
NOTE: Pressing the Power ON/OFF button to an off position or pressing Start /
PAUSE button, does NOT disconnect the appliance from the power supply.
English
ELECTRICAL REQUIREMENTS
WARNING!
Avoid fire hazard or electric shock. Do not use an extension cord or an
adapter plug. Do not remove any prong from the power cord.
English
Front
Back
PARTS AND FEATURES
5
Cycles
Dry
Time
Temp
Start
Pause
Power
On/Off
Dry
Cooling
End Cycle
Clean Lint
Normal
Timed Dry
Heavy
Delicate
30
60
90
120
High
Low
Air-Dry
150
Status
A
U
T
O
D
R
Y
HLP141E
Drum
Windows
(HLP141E Only)
Exhaust and Lint Filters
Door
Door Gasket
Air Intake
Digital Control Panel
Dryer Hanging Wall Hook
Power Cord Exhaust Vent
Hose Clamp Exhaust Housing
Casing Back Cover
Spacer
English
SET UP INSTRUCTIONS
6
Tools and Parts Required for Installation:
Philips Head Screw Driver•
Flat Head Screw Driver•
Electric Drill and 1/8 inch drill bit•
Stud finder (optional)•
(6) Wood screws for mounting plywood•
Plywood board; size 30 (h) by 24(w) inches or wood slats•
Venting materials:
4 inch diameter metal exhaust rigid ducting and fittings or UL flexible metal•
dryer vent hose, that should not exceed 6 feet.
2 additional hose clamps for ducting outside exhaust vent hose•
Metal Elbows or outdoor vents as needed.•
Location of Your Dryer
First find a suitable location where you can mount the dryer on the wall and still
have access to 120 Volt outlets and exterior venting.
Type: Electric dryer
Rating: Please refer to the rating label regarding detailed information
Size: 26.97x24.8x16.73(inch)
Capacity: 2.6 cu.ft.
Weight: 52.9lbs(24kg)
Check dryer size and ensure a good location for the dryer installation on a•
wall where you can mount the unit using wall studs or beams.
It is recommended to use a plywood board (30 by 24 inches) to mount the•
dryer using the walls beams and studs as support, rather than just wood slats.
Make sure the dryer power cord can reach a 120 Volt outlet.•
Make sure you can connect the exhaust vent to the outside or designated•
dryer vent (in a laundry room).
The length of exhaust ducting should not exceed 6 feet.•
Please read the additional ducting information and warnings in this manual.•
16.73”
26.97”
24.8”
Vent to outside Nearest 120 Volt
AC outlet
English
7
Assemble Dryer for Installation
Screw mounting hook bracket and wall spacer to dryer with screws provided.
1. Attach Hanging hook bracket
using the 4 screws.
3. Attach Exhaust Housing. Connect vent housing to dryer using hose clamp
provided to the exhaust pipe.
4. You have two choices of the exhaust pipe housing direction.
2. Attach the 2 wall spacers to the bottom
of the dryer, using the 2 screws.
Spacers
Exhaust Vent Housing
Hose Clam
Exhaust Pipe
English
8
Venting The Dryer
Proper venting of the dryer is very important. Determine the best and safest
ducting for the dryer.
Exhaust Requirements and Maintenance.
Clothes dryer installation must be performed by qualified installer.1.
Install the clothes dryer according to the manufacturer’s instructions and local codes.2.
Do not install a clothes dryer with flexible plastic venting materials. If flexible metal3.
(foil type) duct is installed, it must be of a specific type identified by the flexible duct
manufacturer as suitable for use with clothes dryers. Flexible venting materials are
known to collapse, be easily crushed, and trap lint. These conditions will obstruct
clothes dryer airflow and increase the risk of fire.
Clean old ducts before installing this dryer.4.
WARNING!
WARNING!
Outside
Vent
Correct Incorrect
Venting must conform to local building codes.•
Do not use thin plastic or foil ducting.•
Use 4 inches (10.2cm) diameter rigid or flexible metal duct (note: venting•
materials are not supplied with the dryer, and you should obtain the venting
materials necessary for proper installation at your local hardware store).
Position the Dryer such that the exhaust duct run is as short as possible.•
Make sure there is no more than 6 feet of exhaust ducting.
Clean old ducts before installing this dryer•
Never bend or collapse ducting flex hose. Use few elbows joints as needed.•
Use duct tape on all duct joints.•
Insulate ductwork that runs through unheated areas in order to reduce•
condensation and lint build-up on pipe walls.
To reduce the risk of fire and combustion, the dryer must be vented outdoors. Lint
accumulation can cause fires. Check and clean vents and ducting as often as possible.
PLEASE BE AWARE THAT FAILURE TO EXHAUST THE DRYER CORRECTLY WILL VOID THE
DRYER’S WARRANTY.
9
English
INSTALLATION INSTRUCTIONS
Location for installation and options for various walls
1. There are 2 mounting options- either using wood slats or a whole plywood
board. The dryer installation to the wall should be able to accommodate the
weight of the unit of 52 lbs. plus about 10 lbs. for clothing (or approximately
62 lbs). We suggest you use a plywood board for added support and safety,
this is the best way to mount.
2. Determine dryer position on the wall. A minimum of 6”(Inches) is needed
between the top of the dryer and the ceiling for installation.
3. If mounting the dryer above a washing machine, allow sufficient space to
open the top lid of the washer.
4. The Best installation is to add a plywood board to the wall studs. As a
second option- you can use two (2) slats (2 by 4 “) and attach to studs.
English
10
Wall Mounting Instructions
5. For the best installation
Locate the wall studs in order to securely mount the unit on the wall. Use 1
plywood board size 30 (h) by 24(w) inches and mount into the wall studs
using (6) wood screws (not provided)
6. Mark the required dryer bracket position and holes using the template provided.
7. Using the 4 supplied screws attach the 2 wall hanging mounting brackets onto
the plywood. The distance between each bracket should be 6” apart.
Use wood screwsPlywood board
for supporting
the dryer
24 inches
30 inches
Stud
Stud
HLP141E Mounting template
Center and level template
6 inches
Mounting
bracket
Mounting
bracket
Drill holes for dryer
mounting bracket
6 inches
You are now ready to hang the dryer to the wall.
11
English
8. Hanging dryer on wall
Lift the dryer (with the help of an assistant) and insert the hanging hook onto
the 2 mounting brackets on the wall. The wall spacer will distance the dryer
from the bottom.
Completing Installation
9. Connect ducting to the dryer
Connect the exhaust ducting (not provided) from the dryer venting housing to
external outside dryer vent using a hose clamp (not provided).
10. Competed final installation, on wall with ducting.
Hang dryer onto
mounting brackets
on the wall
Note Must purchase these parts from local hardware store.
hose clamp
Exhaust Ducting
hose clamp
Outside
Vent
Exhaust
Housing
Outside Vent
Note
Vent to the outside only. Improper taping
to vent or unstable installation to vent will
cause undesirable drying performance.
Otros manuales para HLP141E
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Secadora de Haier
Haier
Haier GDZ5-1 Manual de usuario
Haier
Haier GDZ13-0677 Manual de usuario
Haier
Haier HD80-01 WH HA AA Manual de usuario
Haier
Haier I-Pro 5 Series Manual de usuario
Haier
Haier HDY6.1 HA AA Manual de usuario
Haier
Haier HD70-01 ME Manual de usuario
Haier
Haier HD80-256A Manual de usuario
Haier
Haier HD80-01-U Manual de usuario
Haier
Haier GDZ5-1 Manual de usuario
Haier
Haier HDHP80A1 Manual de usuario
Haier
Haier HDY60M Manual de usuario
Haier
Haier HD80-26A Manual de usuario
Haier
Haier GDE480BW Manual de usuario
Haier
Haier GDZ22-1 Manual de usuario
Haier
Haier TCD60E Manual de usuario
Haier
Haier QFT15 Series Instrucciones originales
Haier
Haier HMS6-1 Manual de usuario
Haier
Haier LDS7HC Manual de usuario
Haier
Haier HLF11PC - 06-04 Manual de usuario
Haier
Haier Ginesis HLF103Q Manual de usuario
Manuales populares de Secadora de otras marcas
Indesit
Indesit IDV 75 Manual de usuario
Infiniton
Infiniton SD-DG85C Manual de usuario
BOMANN
BOMANN WT 5019 Manual de usuario
Alliance Laundry Systems
Alliance Laundry Systems TMB795C Manual de usuario
Asko
Asko T793C Manual de usuario
Kenmore
Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario