Haier Ginesis HLF103Q Manual de usuario

Electric D_er

S@cheoJinge Genesis

Secad@ra £J@¢trica

iiiii!!i:l!! T

WARNING - To reduce the risk of fire, electric shock, or iniury

to persons when using your appliance, follow the basic

precautions, including the following:

Read all of the instructions before using this applianceo

Don't dry articles that have been previously cleaned in, washed in,

soaked in, or spotted with gasoline, dry clean solvents or other

flammable explosive sub stains as they give off vapors which could

ignite or explode.

Do not allow children to play on or in the appliance. Close

supervision of children is necessary when the appliance is used near

children.

4. Before the appliance is removed from service or discarded, remove

the door to the drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to

water and/or to the weather.

10.

11.

12.

13.

14.

Do not tamper with controls.

Do not repair or replace any part of the appliance or attempt any

servicing unless specifically recommended in the user-repair

instructions that you understand and have skills to carry out.

Do not use fabric softeners or products to eliminate static unless

recommended by the manufacturers of the fabric softener or

product.

Do not use heat to dry articles or products to eliminate static unless

recommended by the manufacturers of the fabric softener or

product.

Clean lint screen before or after each load.

Keep area around the exhaust opening and adjacent surrounding

areas free from the accumulation of lint, dust and dirt.

The interior of the appliance and the exhaust duct should be cleaned

periodically by qualified service personnel.

Do not place items exposed to cooking oils in your dryer. Items

contaminated with oil may contribute to a chemical reaction than

could cause a load to catch fire.

] 5. If material has been used with any flammable liquids or solids, it

should not used in the dryer until all terraces of flammable liquids

and its fumes have been removed.

16.Thisdryermustbeproperlyinstalledinaccordancewiththe

installationinstructionsbeforeitisused.Seegroundinginstructionsin

theinstallationssections.

17.Propergroundingmustbeensuredtoreducetheriskofelectricshock

andforce.Checkwithaqualifiedelectricianorservicepersonnelif

youareindoubtastowhetherthedryerisproperlygrounded.

18.Usethedryeronlyforitsintendedpurpose,dryingclothes.

19.Alwaysdisconnectdryerfromelectricalsupplybeforeattemptingany

service.Disconnectpowercordbygraspingtheplug,notthecord.

20.Replacewornpowercordand/orlooseplugs.

21.Toreducetheriskofelectricshockorfire,donotuseextensioncords

oradapterstoconnectdryerdectricalpowersource.

SAVETHESEINSTRUCTIONS

Risk of child entrapment. Before you throw away your old

dryer, take off the door so that children may nat get trapped

inside.

Thank you for using our Haler

product. This easy-to-use manual

will guide you in getting the best

use of your dryer.

Remember to record the model and

serial number. They are on a label

in back of the dryer.

Model number

Serial number

Date of purchase

Staple your receipt to your manuak

You will need it to obtain warranty service.

PAGE

SAFETY INSTRUCTIONS .................................................................... 1

|NSTALLATIION |NSTRUCT|ONS ................................................ 4-12

Tools and Materials Required ................................................................ 4

Electrical Requirements ........................................................................ 4

Unpacking Your Dryer ........................................................................ 4

Exhaust System Connections ................................................................ 5

Requirements and Instructions .............................................................. 5

Materials ............................................................................................ 5

Location of Your Dryer ........................................................................ 7

Installation in Mobile Home ................................................................ 7

Electrical Connections ........................................................................ 9

Requirements and Instructions .............................................................. 9

3-Wire Cord Connections .................................................................. 10

4-Wire Cord Connections ............................................................ 11-1:2

OPERATING INSTRUCTIONS .................................................... 13-21

Understanding the Control Panel ........................................................ 13

Preparations before drying .................................................................. 15

Load clothes into dryer ...................................................................... 16

Auto Dry Cycle ............................................................................ 16-18

Timed Dry Cycle ................................................................................ 19

Rack Dry Cycle .................................................................................. :20

Other Features .................................................................................. :20

Normal Operating Sounds ................................................................ 21

Tips .................................................................................................. :21

CARE AND CLEAH|NG GU|DE .......................................................... 21

TROUBLESHOOTING ...................................................................... 22

WARI_NTY" ...................................................................................... 23

,Select a suitable location for the dryer on a hard even surface away from

direct sunlight or heat sources, baseboard heaters, cooking appliances etc.

Any floor unevenness should be corrected with leveling legs located on the

bottom of the dryer.

Tooms and materi ls required

"Phillips head and flathead screwdrivers

.ChanneHock adjustable pilers

*1/2 inch open end wrench

*Carpenter's level

"Measuring tape (] 2ft. min.)

*Duct tap

*Rigid or flexible metal 4 inch (t 02cm) duct

°Vent hood

Emectric m requirements

U.S. Only

Power supply:

3 or 4 wire, 240 Volt, 30 Amp,60Hz, 1 Phase Power Supply Cord Kit (not

supplied when sold in the United States) - Purchase to meet local electrical codes.

The dryer MUST employ a 3-conductor power supply cord NEMA ] 0-30 Type

SPDTRATEDAT 240 Volt AC minimum, 30 Amp., with 3 open end spade lug

connectors with upturned ends or closed loop connectors and marked for use with

clothes dryers. If being installed in a manufactured (mobile) home,the dryer MUST

employ a 4-conductor power supply cord. NEMA ]4-30 type SRDT or ST (as

required) rated at 240 Volt AC Minimum, 30 Amp., with 4 open end spade lug

connectors with upturned ends or dosed loop connectors and marked for use with

clothes dryers. See Electrical Connections for A 4-Wire System.

Canada On|y

Candian models are supplied with the appropriate power cord.

Unpacking Your Dryer

1. Remove all packaging material. This includes the foam base and all adhesive

tape holding the dryer accessories inside and outside.

2. Inspect and remove any remains of packaging, tape or printed materials

before using the dryer.

Requirements and |nstructions

The fol|owing are specific requirements for proper

and safe operation of your dryer. Failure to follow

these instructions can create excessive drying times

and fire hazards.

1. Do not use plastic flexible duct to exhaust the dryer_ Excessive lint can build

up inside exhaust system and create a fire hazard and restrict air flow.

Restricted air flow will increase dryer times, if your present system is made up

of plastic duct or metal foil duct, replace it with a rigid or flexible metal duct.

Ensure present duct is free of any lint prior to installing dryer duct.

2. if the dryer is on exhausted out doors, some fine lint will be expelled into the

laundry area. An accumulation of lint in any area of the home can create a

health and fire hazard. To reduce risk of fire, dryer MUST BEEXHAUSTED

OUTDOORS.

3. Do not allow combustible material (for example: clothing, draperies/curtains,

paper) to come in contact with exhaust system. The dryer must not be

exhausted into a chimney, a wall,a ceiling,or any concealed space of a

building which can accumulate lint, resulting in a fire hazard.

4. Exceeding the length of duct pipe or number of elbows allowed in the

"Maximum Length" charts can cause an accumulation of lint in the exhaust

system, Plugglng the system could create a fire hazard, as well as increase

drying times.

5. Do not screen the exhaust ends of the vent system, nor use any screws of

rivets to assemble the exhaust system. Lint can become caught in the screen,

as increasing drying times. Use an approved vent hood to terminate the duct

outdoors, and seal all joints with duct tape. All male duct pipe fittings must

be installed downstream with the flow of air.

_Explosion hazard:

Do not install the dryer where gasoline of other flammable are kept or

stored_

if the dryer is installed in a garage, it must be minimum of 18 inches

(45.7cm) above the floor. Failure to do so can result in death, explosion,

fire of burns.

Materla|s

Use only 4 inch (t0.2cm) diameter (minimum) rigid of flexible metal duct and

approved vent hood which has a swing-out damper hat open when the dryer is

in operation. When the dryer stops, the dampers automatically dose to prevent

drafts and the entrance of insects and rodents. To avoid restricting the outlet,

maintain a minimum of ] 2 inches (30.5cm) clearance between the vent hood and

the ground or any other obstruction. The vent flap should be able to move freely.

Although vertical orientation of the exhaust system is acceptable. Certain

extenuating circumstances could affect the performance of the dryer:

1. Only rigid metal duct work should be used.

2. Venting vertically through a roof may expose the exhaust system to down

drafts causing an increase in vent restriction.

3. Running the exhaust system through an area not insulated may cause

condensation and faster accumulation of lint.

4. Compression of crimping of the exhaust system will cause an increase in vent

restriction.

The exhaust system should be inspected and cleaned a minimum of every 12

months with normal usage. The more the dryer is used the more often you should

check the exhaust system and vent hood for proper operation.

Do Not Install Your Dryer:

• In an area exposed to dripping water or outside weather conditions.

,In an area where it will come in contact with curtains, thick carpet,or any

thing that will obstruct the flow of combustion and ventilation air.

•On carpet floor must be sdid with a maximum slope of linch (2.54 cm).

_FAR VIFV¢ @ rJF_FW

•Dryer must be exhausted outside (outdoors, not beneath the mobile home)

using metal ducflng that will not support combustion. Metal ducting must be

4 inches (] 0.]6 cm) in diameter with no obstructions° Rigid metal duct is

preferred.

.If dryer is exhausted through the floor and area beneath the mobile home is

enclosed, the exhaust system must terminate outside the enclosure with the

termination securely fastened to the mobile home structure.

Refer to previous pages for other important venting requirements.

•Installation must conform to current Manufactured Home Construction &

Safety Standard.

Corr_t

_rr_:t

Corr

_ncorrect

Incorrect

Requirements and instructions

The foffowing are specific requirements for proper

and safe electrical insta||ation of your dryer. Faffure

to foffow these instructions can create

electrical shock and/or fire hazard.

1. This appliance must be properly grounded. Electrical shock can result if the

dryer is not properly grounded. Follow the instructions in this manual for

proper grounding.

2. Do not use an extension cord with this dryer. Some extension cords are not

designed to withstand the amounts of electrical current this dryer utilizes and

can melt, creating electric shock and/or fire hazard. Locate the dryer within

reach of the receptacle for the length power cord to be purchased, allowing

some slack in the cord. Refer to the electrical requirements in this manual for

the proper power cord to be purchased.

3. A UL approved strain relief must be installed onto power cord. If the strain

relief is not attached, the cord can be pulled out of the pulled out of the

dryer and can be cut by any movement of the cord, resulting in electrical

shock.

4. Do not use an aluminum wire receptacle with copper wired power cord and

plug (or vice versa ). A chemical reaction occurs between copper and

aluminum and can cause electrical shorts. The proper wiring and receptacle

is a copper wired power cord with a copper wired receptacle.

Note: Dryers operating on 208 Volt power supply sill have longer drying times

than operation on 240 Volt power supply.

Danger: Improper connection of the equipment grounding conductor can

result in a risk of electrical shock. Check with a licensed

electrician if you are in doubt as to whether the appliance is

properly grounded.

Otros manuales para Ginesis HLF103Q

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Secadora de Haier

Haier

Haier ProSoft Manual de usuario

Haier

Haier HDM3.5-1 Manual de usuario

Haier

Haier T60-32 Manual de usuario

Haier

Haier GE CleanSpeak WE04X20528 Guía de configuración

Haier

Haier GDZ10-0677 Manual de usuario

Haier

Haier GDG480BW Manual de usuario

Haier

Haier HDC80E1 Manual de usuario

Haier

Haier HDY6-1 Manual de usuario

Haier

Haier GDZ5-1 Manual de usuario

Haier

Haier HD80-26A Manual de usuario

Haier

Haier HLF11E Manual de usuario

Haier

Haier CGDE450AW Manual de usuario

Haier

Haier HD70-A82 Manual de usuario

Haier

Haier EDC1070M Manual de usuario

Haier

Haier HD80-79 Manual de usuario

Haier

Haier GDZ607VA Manual de usuario

Haier

Haier HLF13E Manual de usuario

Haier

Haier HD80-01 WH HA AA Manual de usuario

Haier

Haier HLF13E Manual de usuario

Haier

Haier QFD15 Series Instrucciones originales

Haier

Haier GDG900AW Manual de usuario

Haier

Haier HD90-A636 Manual de usuario

Haier

Haier HDY60M Manual de usuario

Haier

Haier GDZ3.5-1 Manual de usuario

Manuales populares de Secadora de otras marcas

Bosch

Bosch WTA79200GB Manual de usuario

Amana

Amana W10233410A Manual de usuario

Miele

Miele TWH 780 WP Manual de usuario

Asko

Asko T760 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Manual de usuario

Bosch

Bosch Logixx 10 WTB76556GB Hoja de especificaciones

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Manual de instrucciones

Electrolux

Electrolux EW2H328R2 Manual de usuario

Beko

Beko DS8433RX1M Manual de usuario

Dawlance

Dawlance Spinner DS 6000 C Manual de usuario

Electrolux

Electrolux TP5080TW Manual de usuario

AEG

AEG TR838P4OB Manual de usuario

Indesit

Indesit IDV 75 Manual de usuario

Infiniton

Infiniton SD-DG85C Manual de usuario

BOMANN

BOMANN WT 5019 Manual de usuario

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Manual de usuario

Asko

Asko T793C Manual de usuario

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario