Hach FilterTrak 660 Manual de usuario

52364-89

FilterTrak™ 660 Calibration Kit

General Information

The Calibration Kit, shown in Figure 1, is shipped with the calibration body (stand mounted),

a 1-liter bottle of 800 mNTU StablCal®Standard, and a funnel to reduce bubbles when

pouring the standard. The 800 mNTU StablCal Standard is assayed and the value is

reported on the label to the nearest 1 mNTU. The tolerance of the standard is ±50 mNTU.

Figure 1 Calibration Kit Components

Calibration Procedure

1. Remove the cover.

2. Rinse the calibration body with deionized water.

3. Drain all deionized water from the body and replace the drain plug.

4. Clean the FilterTrak 660 Nephelometer head assembly as described in the FilterTrak

660 Laser Nephelometer Instrument Manual (Cat. No. 52300-18).

5. Gently invert the StablCal Standard bottle 50 times to mix. Each inversion should last

1-3 seconds. Do not shake the standard.

6. Place the funnel into the end of the bubble trap, opposite the water intake. See Figure 2.

7. Slowly pour the standard into the funnel.

8. Install the FilterTrak 660 head assembly on the calibration body. See Figure 3.Allowthe

standard to sit undisturbed in the body for approximately 10–20 minutes before

proceeding with the calibration.

9. Calibrate using the instructions in the FilterTrak 660 Laser Nephelometer

Instrument Manual.

Calibration Body

Funnel

800 mNTU StablCal

1-liter Bottle

FilterTrak™ 660 Calibration Kit

HACH COMPANY

WORLD HEADQUARTERS

Telephone: (970) 669-3050

FAX: (970) 669-2932

FORTECHNICAL ASSISTANCE, PRICE INFORMATION AND ORDERING:

Call 800-227-4224

Contact the HACH office or distributor serving you.

www.hach.com [email protected]

In the U.S.A.–

Outside the U.S.A.–

On the Worldwide Web –; E-mail –

toll-free

10. When the calibration is complete, drain the calibration body. The standard cannot be

stored for future use.

11. Remove the head assembly and carefully rinse the head assembly and calibration body.

Immediately reinstall the head assembly back on the FilterTrak 660 body.

12. Store the calibration body with the cover securely in place.

Figure 2 Pouring the StablCal Standard

Figure 3 Calibration Body with FilterTrak 660 Head Assembly in Place

Place the funnel into the body.

Slowly pour the StableCal

Standard into the funnel

Drain

CONFIGURE

STATUS

POWER

REMOTE

Laser Turbidimeter

FilterTrak 660

™

FilterTrak 660

™

Tabla de contenidos

Otros manuales de Instrumento de medición de Hach

Hach

Hach QbD1200 AutoSampler Manual de usuario

Hach

Hach HQ11d Manual rápido

Hach

Hach TL2350 Manual rápido

Hach

Hach LANGE LOC 100 Manual de usuario

Hach

Hach K1100 Manual rápido

Hach

Hach polymetron 9240 Manual de usuario

Hach

Hach pHD Sensor Manual de usuario

Hach

Hach POLYMETRON 8810 ISE Manual rápido

Hach

Hach DR/820 Manual de usuario

Hach

Hach POLYMETRON 83 series Manual de usuario

Hach

Hach 2100P Guía de referencia

Hach

Hach H135 miniLab Manual de usuario

Hach

Hach QbD1200+ Manual de usuario

Hach

Hach 2100Q Manual rápido

Hach

Hach 9525sc Manual de usuario

Hach

Hach LDO10101 Manual de usuario

Hach

Hach Polymetron 9611sc Manual de usuario

Hach

Hach Intellical MTC30101 Manual de usuario

Hach

Hach 500sc SiO2 Manual de instrucciones

Hach

Hach DR 3900 Manual rápido

Hach

Hach 59530-16 Manual de usuario

Hach

Hach TitraLab Manual rápido

Hach

Hach 2200 PCX Manual rápido

Hach

Hach 2100N Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario