Hach DR/2010 Manual de usuario

46645-88

DR/2000 and DR/2010 Spectrophotometer

Lamp Replacement

Purpose

These instructions provide a step-by-step procedure for replacing the lamp in DR/2000 and

DR/2010 Spectrophotometers. Remember, a wavelength calibration adjustment must be done

after replacing the lamp. See the Wavelength Calibration Adjustment instructions shipped with

the lamp.

The lamp shipped with this instruction sheet is one of two designs. One lamp has a single square

slot and a light slit (see Figure 1). The other lamp has a v-shaped slot and a square slot (see

Figure 2). Instructions for installing each lamp are slightly different in step 4.

Lamp Replacement

If the lamp fails and must be replaced, proceed as follows.

1. Disconnect the Battery Eliminator and the RS 232 connector. Turn off the power switch and

empty the cell holder. Place the instrument upside down on a padded surface.

2. Remove the two screws securing the lamp compartment cover and remove the cover (see

Figure 1).

3. Remove the lamp retainer screw and metal sleeve from the lamp channel. The sleeve is

tapered at the bottom end, and, because of its snug fit, probably needs to be loosened with a

tool (needle-nose pliers are recommended) for removal. Remove the lamp. Loosen the two

terminal screws to free the lamp leads.

4. To replace a lamp with two notches (Figure 1), place the new lamp in the lamp channel with

the light slit toward the light slit in the channel.

To replace a lamp with a single notch (Figure 2), place the new lamp in the lamp channel

with the V-shaped groove facing the wavelength dial. The square notch in the new lamp

should be placed against the side with the retainer screw.

5. Push the lamp to the bottom of the lamp channel and install. Firmly tighten the lamp retainer

screw and sleeve in the channel to secure the lamp. Secure the sleeve with the beveled end

down. The lamp must be held tightly in the proper position, flush against the bottom, the

end, and the light slit side of the lamp channel (see Figure 2). Connect the lamp leads of the

new lamp assembly at the lamp terminals (lead orientation does not matter).

Do not overtighten.

6. Install the lamp compartment cover. Return the instrument to the upright position and

restore power.

Note: Some internal components are sensitive to static and may be damaged by external static electricity.

Always re-install the lamp cover after maintenance or servicing.

7. Perform the Lamp Calibration Adjustment procedure described in the instruction shipped

with the lamp.

All manuals and user guides at all-guides.com

LAMP REPLACEMENT, continued

Figure 1 Lamp Replacement For Lamp With Two Notches

Lamp Compartment Cover

Lamp Retainer Screw

Metal Sleeve

Lamp Assembly

Lamp Terminals

Light Slit

Lamp

Retainer

Screw

Lamp Holder

Lamp Channel

Lamp holder must

be flush against

bottom and the two

channel surfaces

indicated by arrows.

Lamp

Channel

Lamp Holder

Light Opening

All manuals and user guides at all-guides.com

LAMP REPLACEMENT, continued

Figure 2 Lamp Replacement For Lamp With One Notch

All manuals and user guides at all-guides.com

HACH COMPANY

WORLD HEADQUARTERS

Telephone: (970) 669-3050

FAX: (970) 669-2932

FOR TECHNICAL ASSISTANCE, PRICE INFORMATION AND ORDERING:

Call 800-227-4224

Contact the HACH office or distributor serving you.

www.hach.com techhelp@hach.com

In the U.S.A. –

Outside the U.S.A. –

On the Worldwide Web – ; E-mail –

toll-free

All manuals and user guides at all-guides.com

Otros manuales para DR/2010

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Hach

Hach

Hach DR1300 FL Manual de usuario

Hach

Hach Lange 2100AN Manual rápido

Hach

Hach Surface Scatter 7 Manual de usuario

Hach

Hach Intellical MTC30101 Manual de usuario

Hach

Hach ORBISPHERE G1100 Manual de usuario

Hach

Hach ORBISPHERE 3650 Atex Manual de usuario

Hach

Hach sc200 Manual de usuario

Hach

Hach LANGE LOC 100 Manual de usuario

Hach

Hach CA610 Manual de usuario

Hach

Hach POLYMETRON 8810 ISE Manual rápido

Hach

Hach Lange SensION+ MM 378 Manual de usuario

Hach

Hach POCKET COLORIMETER II Manual de usuario

Hach

Hach 5500sc Manual de usuario

Hach

Hach Lange ORBISPHERE 3100 Manual de usuario

Hach

Hach DR 6000 Manual de usuario

Hach

Hach TitraLab Manual de usuario

Hach

Hach Lange CL17 Manual de usuario

Hach

Hach 910 Manual de usuario

Hach

Hach 5500sc Instrucciones de funcionamiento

Hach

Hach TOC-X5 Manual de usuario

Hach

Hach sensION+ pH3 Manual de usuario

Hach

Hach Polymetron 9523sc pH Manual rápido

Hach

Hach BioTector B3500s Manual de usuario

Hach

Hach HQ440d Manual rápido

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario