Hach CA610 Manual de usuario

DOC023.98.80282

CA610

10/2019, Edition 4

User Manual

Manuel de l'utilisateur

Manual del usuario

Table of Contents

English..............................................................................................................................3

Français......................................................................................................................... 32

Español.......................................................................................................................... 61

Table of Contents

1 Specifications on page 3

2 General information on page 4

3 Installation on page 7

4 User interface and navigation on page 16

5 Startup on page 17

6 Operation on page 18

7 Maintenance on page 20

8 Troubleshooting on page 27

9 Replacement parts on page 30

Section 1 Specifications

Specifications are subject to change without notice.

Specification Details

Dimensions (W x H x D) 34.11 x 47.50 x 17.93 cm (13.43 x 18.70 x 7.06 in.)

Enclosure IP62 rating when the door is latched (indoor use)

Weight 11.3 kg (25 lb)

Installation category II

Pollution degree 2

Protection class I

Altitude 2000 m (6560 ft)

Display LCD, 3.5-digit measurement readout and six-character alphanumeric scrolling text line

Mounting Wall mount

Power requirements 100–115/230 VAC; 90 VA, 50/60 Hz; 2.5 A fuse

Power connection 12 to 18 AWG wire

Operating temperature 5 to 40 °C (41 to 104 °F)

Storage temperature –40 to 60 °C (–40 to 140 °F)

Humidity 90% at 40 °C (90% at 104 °F)

Air purge (optional) 0.1 CFM instrument-quality air, ¼-inch O.D. tubing

Alarm relay outputs Two unpowered SPDT relays, each rated at 5 A resistive, 240 VAC maximum.

Alarm connection 12 to 18 AWG wire

Recorder output One isolated recorder output, 4–20 mA (can be adjusted to 0–20 mA), maximum

impedance 500 ohms

Recorder connection 12 to 18 AWG wire

Maximum reagent usage 0.5 L per month (for each of the two standards and one reagent)

Reagent containers High-density polyethylene 0.5 L bottles contained inside the analyzer enclosure and

vented externally.

Measurement range 0.1 to 10 mg/L fluoride

Accuracy/precision ±10% or ±0.10 ppm; ±7% or ±0.07 ppm

Cycle limit 4.2 minutes

Calibration Two-point log/linear with 0.5 mg/L and 5.0 mg/L fluoride standards

Detection limit 0.10 ppm

Certifications CE. Listed to UL and CSA safety standards by ETL.

English 3

Sample specification

Specification Details

Sample flow rate to sample conditioning 200 to 500 mL/min

Inlet pressure to instrument 1 to 10 psig

Temperature range for sample 5 to 40 °C (41 to 104 °F)

Inlet fitting ¼-inch OD polyethylene tubing with quick-disconnect fitting

Drain fitting ½-inch hose barb

Application sample Drinking/clean water

Section 2 General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or consequential

damages resulting from any defect or omission in this manual. The manufacturer reserves the right to

make changes in this manual and the products it describes at any time, without notice or obligation.

Revised editions are found on the manufacturer’s website.

2.1 Safety information

N O T I C E

The manufacturer is not responsible for any damages due to misapplication or misuse of this product including,

without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent

permitted under applicable law. The user is solely responsible to identify critical application risks and install

appropriate mechanisms to protect processes during a possible equipment malfunction.

Please read this entire manual before unpacking, setting up or operating this equipment. Pay

attention to all danger and caution statements. Failure to do so could result in serious injury to the

operator or damage to the equipment.

Make sure that the protection provided by this equipment is not impaired. Do not use or install this

equipment in any manner other than that specified in this manual.

2.2 Use of hazard information

D A N G E R

Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious

injury.

CAUTION

Indicates a potentially hazardous situation that may result in minor or moderate injury.

N O T I C E

Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special

emphasis.

2.3 Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or damage to the instrument

could occur if not observed. A symbol, if noted on the instrument, will be included with a danger or

caution statement in the manual.

4 English

This symbol, if noted on the instrument, references the instruction manual for operation and/or safety

information.

Electrical equipment marked with this symbol may not be disposed of in European domestic or public

disposal systems. Return old or end-of-life equipment to the manufacturer for disposal at no charge to

the user.

This symbol indicates that the marked item can be hot and should not be touched without care.

This symbol indicates that the marked item requires a protective earth connection. If the instrument is

not supplied with a ground plug on a cord, make the protective earth connection to the protective

conductor terminal.

This symbol indicates the need for protective eye wear.

This symbol indicates a potential pinch hazard.

2.4 Certification

CAUTION

This equipment is not intended for use in residential environments and may not provide adequate protection to

radio reception in such environments.

Canadian Radio Interference-Causing Equipment Regulation, ICES-003, Class A:

Supporting test records reside with the manufacturer.

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de classe A répond à toutes les exigences de la réglementation canadienne

sur les équipements provoquant des interférences.

FCC Part 15, Class "A" Limits

Supporting test records reside with the manufacturer. The device complies with Part 15 of the FCC

Rules. Operation is subject to the following conditions:

1. The equipment may not cause harmful interference.

2. The equipment must accept any interference received, including interference that may cause

undesired operation.

Changes or modifications to this equipment not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment. This equipment has been tested

and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user will be required to

correct the interference at their expense. The following techniques can be used to reduce

interference problems:

English 5

1. Disconnect the equipment from its power source to verify that it is or is not the source of the

interference.

2. If the equipment is connected to the same outlet as the device experiencing interference, connect

the equipment to a different outlet.

3. Move the equipment away from the device receiving the interference.

4. Reposition the receiving antenna for the device receiving the interference.

5. Try combinations of the above.

2.5 Product overview

D A N G E R

Chemical or biological hazards. If this instrument is used to monitor a treatment process and/or

chemical feed system for which there are regulatory limits and monitoring requirements related to

public health, public safety, food or beverage manufacture or processing, it is the responsibility of the

user of this instrument to know and abide by any applicable regulation and to have sufficient and

appropriate mechanisms in place for compliance with applicable regulations in the event of malfunction

of the instrument.

CAUTION

Fire hazard. This product is not designed for use with flammable liquids.

The CA610 Fluoride Analyzer monitors a sample stream continuously for fluoride content. The

analyzer uses an ion-selective electrode (ISE) system to do a test for fluoride in the range of 0.1 to

10 mg/L. Figure 1 shows the main internal components of the analyzer.

6 English

Figure 1 CA610 fluoride analyzer

1 Power switch 8 Keypad/Display

2 Power connections 9 Pinch plate with openings for half-cell electrodes

3 Network and 4–20 mA connections 10 Reagent bottles

4 Air purge, optional 11 Enclosure drain

5 Relay and alarm contact connections 12 Sample inlet

6 Customer access cover 13 Sample drain

7 BNC connectors and valves

Section 3 Installation

D A N G E R

Electrocution hazard. Always remove power to the instrument before making electrical connections.

D A N G E R

Multiple hazards. Only qualified personnel must conduct the tasks described in this section of the

document.

English 7

3.1 Product components

Make sure that all components have been received. Refer to Figure 2. If any items are missing or

damaged, contact the manufacturer or a sales representative immediately.

Figure 2 Product components

1 Analyzer 3 Standard solution, 5.0 mg/L as

F-

5 Installation, maintenance and

half-cell electrode kits

2 Standard solution, 0.5 mg/L as

F-

4 Reagent solution, TISAB

3.2 Remove the shipping spacer wire

1. Loosen the screws that secure the flow cell assembly. Remove the shipping spacer wire. Refer to

Figure 3.

2. Tighten the screws in small increments and alternate between the screws, so that the flow cell

assembly is moved down evenly. Tighten the screws until the flow cell assembly is seated against

the pump housing. Do not overtighten.

8 English

Figure 3 Shipping spacer wire removal

3.3 Install the instrument

Install this instrument on an indoor wall, away from direct sunlight.

• Use ¼-inch screws to install the instrument.

• For a complete purge of the sample line during each cycle, install the instrument as close to the

sample point as possible.

• Make sure that there is sufficient clearance at the bottom and sides to plumb, wire and operate the

instrument.

Refer to Figure 4 and Figure 5.

English 9

Figure 4 Dimensions for wall installation

Figure 5 Door clearance

10 English

Tabla de contenidos

Idiomas:

Otros manuales de Instrumento de medición de Hach

Hach

Hach DR 2800 Manual de usuario

Hach

Hach TL2310 Manual rápido

Hach

Hach K1100 Manual rápido

Hach

Hach HQ440d Manual rápido

Hach

Hach QbD1200 AutoSampler Manual de usuario

Hach

Hach sensION+ EC5 DL Manual de usuario

Hach

Hach CM130 Manual de usuario

Hach

Hach POLYMETRON 8810 ISE Manual rápido

Hach

Hach PHC101 Manual de usuario

Hach

Hach TL2300 Manual rápido

Hach

Hach Lange CL17 Manual de usuario

Hach

Hach POLYMETRON 8810 ISE Manual rápido

Hach

Hach 2100P Guía de referencia

Hach

Hach LANGE LOC 100 Manual rápido

Hach

Hach POLYMETRON 8362 Manual rápido

Hach

Hach EZ Series Manual rápido

Hach

Hach TitraLab Manual rápido

Hach

Hach TOC-X5 Manual de usuario

Hach

Hach H120 Manual de usuario

Hach

Hach Micro Dist Guía del usuario

Hach

Hach DR 3900 Manual rápido

Hach

Hach sc100 1720E Manual de usuario

Hach

Hach TSS Portable Manual de usuario

Hach

Hach DR 1900 Manual rápido

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario