H3C S12500-X Manual de usuario

H3C S12500-X Switch Series

OpenFlow Configuration Guide

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Software version: R1003 and later

Document version: 6W101-20150515

No part of this manual may be reproduced or transmitted in any form or by any means without prior

written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H3Care, , IRF, NetPilot, Netflow,

SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of

Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Preface

The H3C S12500-X documentation set includes 15 configuration guides. These guides describe the

software features for the H3C S12500-X Switch Series and guide you through the software configuration

procedures. These guides also provide configuration examples to help you apply software features to

different network scenarios.

The OpenFlow Configuration Guide describes OpenFlow fundamentals and configuration.

This preface includes:

•Audience

•Conventions

•Obtaining documentation

•Technical support

•Documentation feedback

Audience

This documentation is intended for:

•Network planners

•Field technical support and servicing engineers

•Network administrators working with the S12500-X series

Conventions

This section describes the conventions used in this documentation set.

Command conventions

Convention Descri

tion

Boldface Bold text represents commands and keywords that you enter literally as shown.

Italic Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars, from

which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select at least one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n> The argument or keyword and argument combination before the ampersand (&) sign can

Convention Descri

tion

be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Descri

tion

Boldface Window names, button names, field names, and menu items are in Boldface. For

example, the New User window appears; click OK.

> Multi-level menus are separated by angle brackets. For example, File > Create > Folder.

Symbols

Convention Descri

tion

WARNING An alert that calls attention to important information that if not understood or followed can

result in personal injury.

CAUTION An alert that calls attention to important information that if not understood or followed can

result in data loss, data corruption, or damage to hardware or software.

IMPORTANT An alert that calls attention to essential information.

NOTE An alert that contains additional or supplementary information.

TIP An alert that provides helpful information.

Network topology icons

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports

Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access controller

engine on a unified wired-WLAN switch.

Represents an access point.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

Represents a security product, such as a firewall, UTM, multiservice security gateway, or

load-balancing device.



Represents a security card, such as a firewall, load-balancing, NetStream, SSL VPN, IPS,

or ACG card.

Port numbering in examples

The port numbers in this document are for illustration only and might be unavailable on your switch.

Obtaining documentation

Access the most up-to-date H3C product documentation on the World Wide Web

at http://www.h3c.com.

Click the following links to obtain different categories of product documentation:

[Technical Documents]—Provides hardware installation, software upgrading, and software feature

configuration and maintenance documentation.

[Products & Solutions]—Provides information about products and technologies, as well as

solutions. [Software Download]—Provides the documentation released with the software version.

Technical support

servic[email protected]

http://www.h3c.com

Documentation feedback

You can e-mail your comments about product documentation to info@h3c.com.

We appreciate your comments.

Contents

Configuring OpenFlow················································································································································ 1

Overview············································································································································································1

OpenFlow switch······················································································································································1

OpenFlow port··························································································································································1

OpenFlow flow table ···············································································································································2

Group table·······························································································································································4

Meter table································································································································································4

OpenFlow instance ··················································································································································5

Protocols and standards ··········································································································································5

OpenFlow configuration task list·····································································································································6

{(Optional.) Configuring OpenFlow to forbid MAC address learning ·······················································6

Configuring OpenFlow instances ····································································································································6

Creating an OpenFlow instance·····························································································································6

Associating an OpenFlow instance with VLANs···································································································6

Creating flow tables for an OpenFlow instance ···································································································7

Setting the controller mode······································································································································7

Configuring the maximum number of flow entries for an extensibility flow table ·············································8

Configuring inband management VLANs··············································································································8

Configuring OpenFlow to forbid MAC address learning····················································································9

Configuring the datapath ID ···································································································································9

Activating or reactivating an OpenFlow instance ································································································9

Configuring controllers for an OpenFlow switch········································································································ 10

Configuring controllers and main connections··································································································· 10

Setting the connection interruption mode ··········································································································· 10

Setting OpenFlow timers ··············································································································································· 10

Configuring OpenFlow to support dynamic MAC addresses··················································································· 11

Displaying and maintaining OpenFlow······················································································································· 11

OpenFlow configuration example································································································································ 12

Network requirements··········································································································································· 12

Configuration procedure ······································································································································ 12

Verifying the configuration··································································································································· 13

Index ···········································································································································································14

Configuring OpenFlow

Software-Defined Networking (SDN) was developed to meet the growing requirements of virtualization

technologies and data networks. SDN uses software to separate controlling functions from data

forwarding, and provides simple, flexible device operations and high extensibility.

OpenFlow is the communication interface between a controller and network devices to implement SDN.

With OpenFlow, you can perform centralized data forwarding management for physical and virtual

devices.

This feature is available in Release 1005P04 and later versions.

Overview

OpenFlow separates the data forwarding and routing decision functions. It keeps the flow-based

forwarding function and employs a separate controller to make routing decisions. A switch

communicates with the controller through a secure channel.

Figure 1 OpenFlow network diagram

OpenFlow switch

OpenFlow switches are classified into the following types:

•OpenFlow-only—Supports only OpenFlow operation.

•OpenFlow-hybrid—Supports both OpenFlow operation and traditional Ethernet switching

operations. Switches of this series are OpenFlow-hybrid switches.

OpenFlow port

OpenFlow supports the following types of ports:

•Physical port—Corresponds to a hardware interface of a switch, such as an Ethernet interface. A

physical port can be either an ingress port or an output port.

•Logical port—Does not correspond to a hardware interface of a switch and might be defined by

non-OpenFlow methods. For example, aggregate interfaces are logical ports. A logical port can be

either an ingress port or an output port.

IMPORTANT:

The switch does not support tunnel interfaces and loopback interfaces.

•Reserved port—Defined by OpenFlow to specify forwarding actions. Reserved ports include the

following types:

{All—All OpenFlow ports that can be used to forward a packet.

{Controller—OpenFlow controller.

{Local—Local CPU.

{Normal—Normal forwarding process.

{Flood—Flooding.

Except the Any type, all reserved ports can be used only as output ports.

OpenFlow flow table

An OpenFlow switch matches packets against one or more user-defined flow tables. A flow table consists

of flow entries, and packets are matched based on the matching precedence of flow entries.

OpenFlow flow tables include the following types:

•MAC-IP—Combines the MAC address table and FIB table.

A MAC-IP flow table provides the following match fields:

{Destination MAC address.

{VLAN.

{Destination IP address.

A MAC-IP flow table provides the following actions:

{Modifying the destination MAC address.

{Modifying the source MAC address.

{Modifying the VLAN.

{Specifying the output port.

•Extensibility—Provides more matching fields and actions than a MAC-IP flow table.

Flow entry

Figure 2 Flow entry components

A flow entry contains the following fields:

•Match fields—Matching rules of the flow entry. These consist of the ingress port, packet headers,

and metadata specified by the previous table.

•Priority—Matching precedence of the flow entry. A packet is matched against the table and only

the highest priority flow entry that matches the packet is selected.

•Counters—Counts of the packets that match the flow entry.

•Instructions—To modify the action set or pipeline processing. These include the following types:

{Meter—Directs the packets to the specified meter to limit the rate of the packets.

{Apply-Actions—Applies the specified actions in the action list immediately.

{Clear-Actions—Clears all the actions in the action set immediately.

{Write-Actions—Modifies all the actions in the action set immediately.

{Goto-Table—Indicates the next MAC-IP flow table in the processing line.

Actions are executed in one of the following ways:

{Action Set—When the instruction set of a flow entry does not contain a Goto-Table instruction,

pipeline processing stops and the actions in the action set are executed. An action set contains

a maximum of one action of each type.

{Action List—The actions in the action list are executed immediately in the order specified by the

action list. The effect of those actions is cumulative.

•Timeouts—Maximum amount of idle time or hard time for the flow entry.

{idle Time—The flow entry is removed when it has matched no packets during the idle time.

{hard Time—The flow entry is removed when the hard time timeout is exceeded, regardless of

whether or not it has matched packets.

•Cookies—Flow entry identifier specified by the controller.

OpenFlow pipeline

The OpenFlow pipeline processing defines how packets interact with flow tables contained by a switch.

The flow tables of an OpenFlow switch are sequentially numbered, starting at 0. The packet is first

matched against flow entries of the first flow table, which is flow table 0. A flow entry can only direct a

packet to a flow table number that is greater than its own flow table number.

When a packet matches a flow entry, the OpenFlow switch updates the action set for the packet and

passes the packet to the next flow table. In the last flow table, the OpenFlow switch executes all actions

to modify packet contents and specify the output port for packet forwarding. If the instruction set of one

of the flow tables contains an action list, the OpenFlow switch executes the actions to modify a copy of

the packet immediately in this table.

Figure 3 OpenFlow forwarding workflow

Table-miss flow entry

Every flow table must support a table-miss flow entry to process table misses. The table-miss flow entry

specifies how to process packets that were not matched by other flow entries in the flow table.

The table-miss flow entry wildcards all match fields (all fields omitted) and has the lowest priority 0.

The table-miss flow entry behaves in most ways like any other flow entry.

Group table

The ability for a flow entry to point to a group enables OpenFlow to represent additional methods of

forwarding. A group table consists of group entries.

Figure 4 Group entry components

A group entry contains the following fields:

•Group Identifier—A 32 bit unsigned integer uniquely identifying the group.

•Group Type—Type of the group.

•Counters—Updated when packets are processed by a group.

•Action Buckets—An ordered list of action buckets, where each action bucket contains a set of

actions to execute and associated parameters.

Meter table

Meters enable OpenFlow to implement various simple QoS operations, such as rate-limiting. A group

table consists of meter entries.

Figure 5 Meter entry components

A meter entry contains the following fields:

•Meter Identifier—A 32 bit unsigned integer uniquely identifying the meter.

•Meter Bands—Each meter can have one or more meter bands. Each band specifies the rate at

which the band applies and the way packets should be processed. If the current rate of packets

exceeds the rate of multiple bands, the band with the highest configured rate is used.

•Counters—Updated when packets are processed by a meter.

Figure 6 Band components

A meter band contains:

•Band Type—Packet processing methods. Packets that exceed the band rate are dropped.

•Rate—Defines the lowest rate at which the band can apply.

•Counters—Updated when packets are processed by a band.

•Type Specific Arguments—Some band types have optional arguments.

Otros manuales para S12500-X

Tabla de contenidos

Otros manuales de Cambiar de H3C

H3C

H3C S3100-52P Instrucciones de instalación

H3C

H3C S5590-HI Series Manual de usuario

H3C

H3C UniServer BX608FE Manual de usuario

H3C

H3C S7502 Manual de usuario

H3C

H3C S5500-EI series Manual de usuario

H3C

H3C S6860-54HF Manual de operación y mantenimiento

H3C

H3C S7504E-XS Manual de operación y mantenimiento

H3C

H3C S6825 Series Manual de usuario

H3C

H3C S9500 Series Instrucciones de instalación

H3C

H3C s5820x series Manual de usuario

H3C

H3C S5500-EI series Manual de usuario

H3C

H3C S7500E-XS Series Manual de instalación

H3C

H3C LS-3100-16TP-EI-H3-A-O Manual de usuario

H3C

H3C S5120-SI Series Manual de usuario

H3C

H3C H3C S3600 Series Manual de usuario

H3C

H3C S12500CR Series Manual de usuario

H3C

H3C S9500 Series Manual de usuario

H3C

H3C S5120-EI Series Manual de instalación

H3C

H3C S12500-X Manual de instalación

H3C

H3C S9850 Series Manual de instrucciones

H3C

H3C S5130S-EI series Manual del propietario

H3C

H3C S6520X-SI Series Manual de usuario

H3C

H3C S9500E Series Manual de usuario

H3C

H3C S3610 Series Instrucciones de instalación

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario