GW Instek GSP-830 Manual de usuario

3.0GHz Spectrum Analyzer

GSP-830

USER MANUAL

GW INSTEK PART NO. 82SP-83000MA1

ISO-9001 CERTIFIED MANUFACTURER

This manual contains proprietary information, which is protected by copyrights. All rights

are reserved. No part of this manual may be photocopied, reproduced or translated to

another language without prior written consent of Good Will company.

The information in this manual was correct at the time of printing. However, Good Will

continues to improve products and reserves the rights to change specification,

equipment, and maintenance procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng City, Taipei County 236, Taiwan.

Table of Contents

SAFETY INSTRUCTIONS.................................................................................7

Safety Symbols .................................................................................. 7

Safety Guidelines...............................................................................8

GETTING STARTED .........................................................................................11

GSP-830 Characteristics................................................................12

Package Contents .............................................................................13

Front Panel Overview.......................................................................14

Rear Panel Overview........................................................................17

Display Overview .............................................................................20

Tilt Stand & Power Up .....................................................................22

Error Check ......................................................................................23

Functionality Check .........................................................................24

QUICK REFERENCE.......................................................................................26

Operation Shortcuts........................................................................ 27

Menu Tree .........................................................................................33

Preset Contents................................................................................41

FREQUENCY/SPAN ......................................................................................42

View Signal (Center and Span) ......................................................43

View Signal (Start and Stop)..........................................................45

Full/Zero Span ................................................................................. 47

Recall the Last Span Setting..........................................................48

AMPLITUDE ..................................................................................................49

Set Vertical Scale............................................................................50

Amplitude Correction......................................................................53

Use Pre-Amplifier GAP-801 (Optional)..........................................58

Set Input Impedance .......................................................................59

AUTOSET......................................................................................................60

MARKER .......................................................................................................63

GSP-830 User Manual

Activate/de-activate marker(s)....................................................64

Move marker(s)................................................................................67

Show Markers in Table................................................................... 69

PEAK SEARCH ..............................................................................................70

Search Signal Peaks.........................................................................71

Show Peak Table...............................................................................73

TRACE ..........................................................................................................75

View traced waveform ....................................................................76

Move Marker to Trace .....................................................................78

Run Trace Math ............................................................................... 80

Select Signal Detection Mode.........................................................82

POWER MEASUREMENT............................................................................... 84

ACPR Measurement......................................................................... 85

OCBW Measurement........................................................................ 88

N dB Measurement.......................................................................... 90

Phase Jitter Measurement............................................................. 91

LIMIT LINE ................................................................................................... 92

Edit Limit Line.................................................................................. 93

Run Pass/Fail test.......................................................................... 96

BANDWIDTH ................................................................................................ 98

Select RBW (Resolution BandWidth)............................................. 99

Select VBW (Video BandWidth)...................................................... 101

RBW/VBW Auto Mode Contents .................................................... 102

Set Sweep time .............................................................................. 104

Average Waveform......................................................................... 104

TRIGGER..................................................................................................... 106

DISPLAY...................................................................................................... 110

Change Display Brightness............................................................. 111

Activate Display Line ....................................................................... 111

Enter Display Title........................................................................... 112

Use Split Display ............................................................................. 113

Table of Contents

Use VGA Output ................................................................................114

Save Display Image to USB Flash Drive........................................114

FILE ............................................................................................................. 116

File Location and File Type .............................................................117

File Copy Step...................................................................................118

File Delete Step................................................................................121

File Rename Step ............................................................................123

Save Display Image to USB Flash Drive.......................................124

PRESET ...................................................................................................... 126

SYSTEM.......................................................................................................127

Save/Recall Panel Setting ............................................................128

Configure Communication Interface............................................129

View System Information................................................................131

Set Date/Time.................................................................................135

Synchronize GSP-830 with Other Device................................... 136

Select Menu Language................................................................... 138

Service operation menu ............................................................... 138

SEQUENCE.................................................................................................. 139

Edit Sequence..................................................................................140

Run Sequence..................................................................................143

TRACKING GENERATOR.............................................................................. 145

DEMODULATOR .......................................................................................... 147

EMI FILTER ................................................................................................. 149

BATTERY / DC OPERATION ........................................................................ 151

Battery Operation............................................................................151

DC Operation ...................................................................................152

PC SOFTWARE............................................................................................ 153

Install Software ..............................................................................154

GSP-830 User Manual

Connect Software .......................................................................... 155

Use Software .................................................................................. 158

REMOTE CONTROL....................................................................................... 161

Configure Interface ....................................................................... 162

Command Syntax............................................................................ 164

Command Set.................................................................................. 165

FAQ............................................................................................................. 178

Appendix.................................................................................................... 180

GSP-830 Specification..................................................................180

Optional Items Specifications ...................................................... 182

Declaration of Conformity............................................................ 184

INDEX ......................................................................................................... 185

錯誤! 尚未定義樣式。

SAFETY INSTRUCTIONS

This chapter contains important safety instructions that

you must follow when operating GSP-830 and when

keeping it in storage. Read the following before any

operation to insure your safety and to keep the best

condition for GSP-830.

Safety Symbols

These safety symbols may appear in this manual or on GSP-830.

WARNING

Warning: Identifies conditions or practices that could

result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that could

result in damage to GSP-830 or to other properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

GSP-830 User Manual

Safety Guidelines

•Make sure that the RF input level and the Tracking

Generator output reversed power level do not exceed

+30dBm.

•Do not supply an input signal to the Tracking

Generator output.

•Do not place any heavy object on GSP-830.

•Avoid severe impacts or rough handling that leads to

damaging GSP-830.

•Do not discharge static electricity to GSP-830.

•Use only mating connectors, not bare wires, for the

terminals.

•Do not block or obstruct the cooling fan vent opening.

•Do not perform measurement at power source and

building installation site (Note below).

•Do not disassemble GSP-830 unless you are qualified

as service personnel.

General Guideline

CAUTION

(Note) EN 61010-1:2001 specifies the measurement categories and

their requirements as follows. GSP-830 falls under category II.

•Measurement category IV is for measurement performed at the

source of low-voltage installation.

•Measurement category III is for measurement performed in the

building installation.

•Measurement category II is for measurement performed on the

circuits directly connected to the low voltage installation.

Power Supply

WARNING

•AC Input voltage: 100 ~ 240 V AC, 50/60Hz

•DC Input voltage: 12V DC, 40W maximum

•The power supply voltage should not fluctuate more

than 10%.

•Connect the protective grounding conductor of the

AC power cord to an earth ground, to avoid electrical

shock.

Battery

CAUTION

•Rating: 10.8V Li-Ion battery pack x 2

•Turn Off the main power switch before installing or

taking out the battery packs.

錯誤! 尚未定義樣式。

Fuse

WARNING

•Fuse type: T1.6A/ 250V

•Make sure the correct type of fuse is installed before

power up.

•To ensure fire protection, replace the fuse only with

the specified type and rating.

•Disconnect the power cord before fuse replacement.

•Make sure the cause of fuse blowout is fixed before

fuse replacement.

Cleaning GSP-830 •Disconnect the power cord before cleaning.

•Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid into

GSP-830.

•Do not use chemical or cleaner containing harsh

material such as benzene, toluene, xylene, and acetone.

•Location: Indoor, no direct sunlight, dust free, almost

non-conductive pollution (Note below)

•Relative Humidity: < 90%

•Altitude: < 2000m

•Temperature: 18°C to 28°C

Operation Environment

(Note) EN 61010-1:2001 specifies the pollution degrees and their

requirements as follows. GSP-830 falls under degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

•Pollution degree 1: No pollution or only dry, non-conductive pollution

occurs. The pollution has no influence.

•Pollution degree 2: Normally only non-conductive pollution occurs.

Occasionally, however, a temporary conductivity caused by

condensation must be expected.

•Pollution degree 3: Conductive pollution occurs, or dry,

non-conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment is

normally protected against exposure to direct sunlight, precipitation,

and full wind pressure, but neither temperature nor humidity is

controlled.

Storage Environment •Location: Indoor

•Relative Humidity: < 85%

•Temperature: 0°C to 40°C

GSP-830 User Manual

Power cord for the United Kingdom

When using GSP-830 in the United Kingdom, make sure the power cord

meets the following safety instructions.

NOTE: This lead / appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow: Earth

Blue: Neutral

Brown: Live (Phase)

As the colours of the wires in main leads may not correspond with the

colours marking identified in your plug/appliance, proceed as follows:

The wire which is coloured Green & Yellow must be connected to the Earth

terminal marked with the letter E or by the earth symbol or coloured Green

or Green & Yellow.

The wire which is coloured Blue must be connected to the terminal which is

marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the terminal marked

with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment or contact

the supplier.

This cable/appliance should be protected by a suitably rated and approved

HBC mains fuse: refer to the rating information on the equipment and/or

user instructions for details. As a guide, cable of 0.75mm2 should be

protected by a 3A or 5A fuse. Larger conductors would normally require 13A

types, depending on the connection method used.

Any moulded mains connector that requires removal /replacement must be

destroyed by removal of any fuse & fuse carrier and disposed of immediately,

as a plug with bared wires is hazardous if a engaged in live socket. Any

re-wiring must be carried out in accordance with the information detailed on

this label.

Otros manuales para GSP-830

Tabla de contenidos

Otros manuales de Instrumento de medición de GW Instek

GW Instek

GW Instek GSP-810 Manual de usuario

GW Instek

GW Instek GSP-830TG Manual de usuario

GW Instek

GW Instek GOM-802 Manual de usuario

GW Instek

GW Instek GOM-802 Manual de usuario

GW Instek

GW Instek gpm-8212 Manual de usuario

GW Instek

GW Instek GBM-3080 Manual de usuario

GW Instek

GW Instek GPM-001 Manual de usuario

GW Instek

GW Instek GOM-804 Manual de usuario

GW Instek

GW Instek GFG-8215A Manual de usuario

GW Instek

GW Instek GFC-8270H Manual de usuario

GW Instek

GW Instek PCS-1000 Manual de usuario

GW Instek

GW Instek PEL-3000A Series Manual de usuario

GW Instek

GW Instek GSP-830 Manual de usuario

GW Instek

GW Instek GDP-040D Manual de usuario

GW Instek

GW Instek LCR Series Manual de usuario

GW Instek

GW Instek LCR-8000G Series Manual de usuario

GW Instek

GW Instek GDM-906 Series Manual de usuario

GW Instek

GW Instek AFG-3000 Series Manual de usuario

GW Instek

GW Instek GSP-730 Manual de usuario

GW Instek

GW Instek GSP-730 Manual de usuario

GW Instek

GW Instek GFC-8010H Manual de usuario

GW Instek

GW Instek GSP-9330 Manual del propietario

GW Instek

GW Instek GRF-1300 Manual de usuario

GW Instek

GW Instek GSP-930 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario