Grundig DSR 1750 MICRO Manual de usuario
DIGITAL
SATELLITE
RECEIVER
DSR 1750 MICRO
2
CONTENTS____________________________________________
4-5 General information
4 Packing contents
4 Receiving digital satellite channels
5 Special features of your Digital Satellite Receiver
6 Set-up and safety
7-8 Overview
7 The Digital Satellite Receiver
7 The infrared receiver
8 The remote control
9-10 Connection/preparation
9 Connecting the antenna
9 Connecting the television
10 Connecting the infrared receiver
10 Connecting the power supply unit
10 Inserting batteries into the remote control
11-17 Basic settings
11 The menu
12 Initial setup
13 Setting stations, Option 1
14-15 Setting stations, Option 2
16-17 Editing channel lists
18-20 Basic functions
18 Switching on and off
18 Mode selection
18 Selecting presets directly
18 Selecting stations from lists
19 Adjusting the volume
19 Muting the sound
19 Displaying time
19 Switching from the current station to the previous one
19 Displaying time
19 Using options
20 Electronic TV guide
21 Teletext mode
21 Teletext
21 Additional functions
22-26 Settings
22-23 Video settings
23-24 Language settings
25 Menu settings
26 Miscellaneous settings
27 Timer functions
ENGLISH
3
CONTENTS____________________________________________
28 Additional functions
28 Security functions
29-33 Special settings
29-31 Searching for new stations
31 Specifying the order of stations in the channel list
32 Resetting the digital receiver to its original state
32 Updating the digital receiver software
33 Changing remote control levels
34-37 Upgrading the television
34 Connecting a GRUNDIG television with the Digi 200 G2 chassis
35 Installing on the GRUNDIG television set
36-37 Operating the GRUNDIG television remote control
38-40 Information
38 Displaying station reception properties
38 Displaying device information
39 Technical data
39 Environmental note
40 Troubleshooting
4
Packing contents
1Digital Satellite Receiver DSR 1750 MICRO
2Tele Pilot 766 S remote control
32 batteries for the remote control (2 x 1.5 V, AA type batteries)
4SCART extension cable
5Power supply unit
6Infrared receiver
7Operating manual
Receiving digital satellite channels
In order to use your new DSR 1750 MICRO digital receiver
you need a digital-compatible satellite antenna, which must be
installed and aligned to the desired satellites (for example Astra and
EutelSat/Hotbird).
Unlike broadcasts of analogue satellite channels, not every digital
TV or radio station is assigned to one transmission frequency, but
several TV and/or radio stations are broadcast by one transponder.
To help you with the choice and settings for satellite channels, a
selection of TV and radio stations have already been prepro-
grammed for this device. You can start a channel search to ensure
that any new satellite channels are available on your device.
You can find out how this works and what you need to observe on
page 29 of this operating manual.
Of course, you can easily program new satellite channels. You can
find the latest transponder information on the teletext pages of
various broadcasters, in a current satellite TV magazine or on the
Internet.
GENERAL INFORMATION__________________
ENGLISH
5
Special features of your Digital Satellite Receiver
The DSR 1750 MICRO digital receiver can receive and process all
unencrypted digital channels.
This digital receiver has a built-in digital receiver unit for satellite
channels. The receiver unit converts the signals from digital satellite
channels to provide outstanding audio and picture quality.
To ensure your new digital receiver always uses the latest program
data and operating software, it is first necessary to conduct an
update.
Using the Astra 19.2° East satellite, you can update the device
software of the satellite receiver.
You can find out how this works and what you need to observe on
page 32 of this operating manual.
The TV guide informs you of any schedule changes at short notice,
and also provides an overview of all the channels’ schedules for the
next few hours.
Detailed information on individual television programmes is
available at the touch of a button.
This digital receiver has a highly comprehensive, user-friendly menu
system.
The menu is displayed on the television screen, and the functions of
the remote control buttons are explained.
This receiver is fitted with the Digi 200 chassis for upgrading
GRUNDIG televisions.
The user guide for the receiver can be integrated into the television
user guide by following a brief installation procedure. The receiver
can be controlled with the television remote control once it is
installed. The remote control, infrared receiver and power supply
for the receiver will then no longer be necessary.
GENERAL INFORMATION__________________
6
SET-UP AND SAFETY___________________________
To ensure that this high-quality and user-friendly digital receiver
provides you with many years of entertainment, please observe the
following instructions:
This digital receiver set is designed to receive video and audio
signals. Any other use is expressly prohibited.
When setting up the device, make sure the mains plug is easily
accessible.
If the digital receiver is subject to a sudden change in temperature,
for example when brought in from the cold to a warm room, leave
it to stand for at least two hours before you connect it to the mains
supply.
Do not expose the digital receiver to moisture of any kind.
The digital receiver is designed for use in dry rooms. If you do use
it outdoors, make sure it is protected from moisture such as rain or
splashing water.
Thunderstorms are a danger to all electrical devices. Even if the
digital receiver is switched off, it can be damaged by a lightning
strike to the mains or the antenna.
Always disconnect the mains and antenna plugs during a storm.
Never open the digital receiver casing under any circumstances.
Warranty claims are excluded for damage resulting from improper
handling.
Note:
Do not connect any other equipment while the device is switched
on.
Switch off the other equipment as well before connecting it.
Do not plug in the power supply of your device until you have
connected the external equipment and the antenna.
Make sure the power supply is freely accessible.
ENGLISH
7
The Digital Satellite Receiver
ʐʐ
Antenna socket for the satellite antenna.
IR remote Connection socket for infrared receiver
12 VDC, 18 W max. Connection socket for the enclosed power supply
unit.
EURO AV Scart connector (output) for connection to TV.
The infrared receiver
The infrared receiver receives the infrared signals for the remote
control and forwards the commands by wire to the receiver. Position
the infrared receiver so that it can receive the remote control
commands.
When you switch on from standby, the receiver switches to the last
selected station (Last Station Memory).
•(red) The digital receiver is in standby mode.
•(green) The digital receiver is switched on.
OVERVIEW____________________________________________
8
OVERVIEW____________________________________________
The remote control
ǼSwitches the digital receiver to standby, and from
standby to the channel last selected.
PIP This button has no function.
EDisplays the picture format and the sound informa-
tions.
?Displays programme information.
1 … 0 Select stations.
dSwitches the sound to mute and back on again.
iOpens and closes the main menu.
ZSwitches back one menu level.
P+ P- Switches up or down the channels.
ǸǷ Adjust the volume.
OK Calls up the list of channels or favourites.
TXT Switches from TV mode to teletext mode, mix mode
and back to TV mode.
TV-G Opens and closes the electronic TV guide.
TV
Switches to TV mode.
MHP
This button has no function.
A/B
Switches between the last two selected stations;
Switches from the station list to the favourites.
RADIO Switches to radio mode.
ȄDisplays the time.
ǷǷSwitches the sound from stereo to mono;
z FCalls up options (not available for all stations).
DR, TV Switches to operating a second GRUNDIG
DVD digital receiver, GRUNDIG television or
GRUNDIG DVD player.
Keep the appropriate button (»DR«, »TV«, »DVD«)
pressed down, then press the required button.
Note:
The functions available depend on the model of the
device you are using.
Simply try it out.
Tele Pilot 765 S
AVR DVD
TV
z
TXT
PIP
A/B
MHP
d
TV-G
Radio
TV
ENGLISH
9
Connecting the antenna
1Connect the antenna cable of the satellite antenna to the »ʐʐ«
socket on the digital receiver (screw connector, F connector).
Connecting the television
1Plug the digital receiver into the corresponding scart socket on
the television (use enclosed scart extension if required).
CONNECTION/PREPARATION __________
7
12
10
Connecting the infrared receiver
1Plug the infrared receiver into the »IR remote« socket.
Connecting the power supply unit
1Insert the plug of the enclosed power supply unit into the
»12 VDC« socket of the digital receiver.
2Insert the power supply unit into the wall socket.
Notes:
Do not insert the power supply unit of your device into the sock-
et until you have connected the television and the antenna.
The only way to fully disconnect the digital receiver from the
mains supply is to pull out the power supply.
Inserting batteries into the remote control
1Open the battery compartment by removing the lid.
2Insert the batteries (AA, 2 x 1.5 V).
Make sure the polarity is correct (as shown on the base of the
battery compartment).
3Close the battery compartment.
Note:
If the digital receiver no longer reacts properly to remote control
commands, the batteries may be flat. Always remove used bat-
teries.
The manufacturer accepts no liability for damage caused by
leaking batteries.
Environmental note
Batteries, including those which contain no heavy metal, should
not be disposed of with household waste. Please dispose of
used batteries in an environmentally sound manner and in
accordance with the legal regulations that apply in your area.
CONNECTION/PREPARATION __________
Tabla de contenidos
Otros manuales de Receptor de Grundig
Grundig
Grundig DSR 6454 HD/CD Manual de usuario
Grundig
Grundig YB 218 Manual de usuario
Grundig
Grundig DTR 1560-2 MICRO Manual de usuario
Grundig
Grundig STR 100 microSAT Manual de usuario
Grundig
Grundig GSS.box DSI 400 Manual de usuario
Grundig
Grundig RR 740 CD Manual de usuario
Grundig
Grundig Yacht Boy 2000 Manual de usuario
Grundig
Grundig GSTB1701USB Manual de usuario
Grundig
Grundig SER 300 Manual de usuario
Grundig
Grundig STR 632 Manual de usuario
Grundig
Grundig SER 251 Manual de usuario
Grundig
Grundig STR 6122 Manual de usuario
Grundig
Grundig DTR 1782 VC Manual de usuario
Grundig
Grundig DTR 1560 MICRO Manual de usuario
Grundig
Grundig GUFSAT02SD Manual de usuario
Grundig
Grundig V21 Manual de usuario
Grundig
Grundig DRS 100 CL Manual de usuario
Grundig
Grundig DTR 1524 Manual de usuario
Grundig
Grundig STR 7122 TWIN Manual de usuario
Grundig
Grundig STR 100 DX microSAT Manual de usuario
