Grundfos CIM 500 Manual de usuario

CIM 500 Ethernet module

Installation and operating instructions

GRUNDFOS INSTRUCTIONS

Table of contents

CIM 500 Ethernet module

English (GB)

Installation and operating instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Deutsch (DE)

Montage- und Betriebsanleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Dansk (DK)

Monterings- og driftsinstruktion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Español (ES)

Instrucciones de instalación y funcionamiento . . . . . . . . . . . . . . . . . . . . . . . . . 34

Suomi (FI)

Asennus- ja käyttöohjeet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Français (FR)

Notice d'installation et de fonctionnement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Italiano (IT)

Istruzioni di installazione e funzionamento . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Português (PT)

Instruções de instalação e funcionamento . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

 (RU)

,     . . . . . . . . . . . . . . . . . . . 77

中文 (CN)

安装和使用说明书. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

日本語(JP)

取扱説明書 ..........................................................94

한국어 (KO)

설치 및 작동 지침 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102

Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

English (GB)

English (GB) Installation and operating instructions

Original installation and operating instructions

CONTENTS

Page

1. Symbols used in this document

2. Applications

The CIM 500 Ethernet module enables data

transmission between an industrial Ethernet network

and a Grundfos product.

The module supports various industrial Ethernet

protocols. See section 3.2 Selection of industrial

Ethernet protocol.

The module is fitted in the product to be

communicated with or in a CIU 500.

Retrofitting of the module is described in the

installation and operating instructions of the

Grundfos product.

Configuration is done via the built-in web server,

using a standard web browser on a PC.

See the specific functional profile on the DVD

supplied with the Grundfos product.

1. Symbols used in this document 4

2. Applications 4

2.1 Abbreviations 5

2.2 CIM 500 Ethernet module 5

3. Installation 6

3.1 Connecting the Ethernet cable 6

3.2 Selection of industrial Ethernet protocol 7

3.3 Setting up the IP addresses 7

3.4 Connection to the web server 7

4. Status LEDs 8

5. Data activity and link LEDs 9

6. Fault finding 10

6.1 Modbus TCP/BACnet IP 10

6.2 PROFINET IO 12

6.3 GRM IP 14

7. Technical data 15

8. Service 15

8.1 Service documentation 15

9. Disposal 15

Warning

Prior to installation, read these installation

and operating instructions. Installation and

operation must comply with local

regulations and accepted codes of good

practice.

Warning

If these safety instructions are not

observed, it may result in personal injury.

Caution

If these safety instructions are not

observed, it may result in malfunction or

damage to the equipment.

Note

Notes or instructions that make the job

easier and ensure safe operation.

English (GB)

2.1 Abbreviations 2.2 CIM 500 Ethernet module

Fig. 1 CIM 500 Ethernet module

APDU Application Protocol Data Unit

ARP

Address Resolution Protocol.

Translates IP addresses to MAC

addresses.

CAT5 Ethernet cable type with four

twisted-pair cables.

CAT5e Enhanced CAT5 cable with better

performance.

CAT6 Cable with very high performance.

CIM Communication Interface Module

CIU Communication Interface Unit

DHCP

Dynamic Host Configuration Protocol.

Used to configure network devices so

that they can communicate via an IP

network.

DNS Domain Name System. Used to resolve

host names to IP addresses.

GENIpro Proprietary Grundfos fieldbus protocol

GND Ground

HTTP

Hyper Text Transfer Protocol. The

protocol commonly used to navigate the

world wide web.

IANA Internet Assigned Numbers Authority.

IP Internet Protocol

LED Light-emitting diode

MAC Media Access Control. Unique address

for a piece of hardware.

Ping Signal sent to analyse the round-trip

time delay.

SELV Separated or Safety Extra-Low Voltage

SELV-E Separated or Safety Extra-Low Voltage

with earth

SMTP Simple Mail Transfer Protocol.

SNTP

Simple Network Time Protocol. Used for

clock synchronisation between

computer systems.

TCP Transmission Control Protocol. Protocol

suitable for Internet communication.

URL Uniform Resource Locator. The IP

address used to connect to a server.

UTC

Coordinated Universal Time. The

primary time standard by which the

world regulates clocks and time.

TM05 7431 1013

Pos. Designation Description

1ETH1

Industrial Ethernet RJ45

connector 1

2ETH2

Industrial Ethernet RJ45

connector 2

3DATA1

Data activity LED for

RJ45 connector 1

4LINK1

Link LED for RJ45

connector 1

5DATA2

Data activity LED for

RJ45 connector 2

6LINK2

Link LED for RJ45

connector 2

7LED1

Red/green status LED for

Ethernet communication

8LED2

Red/green LED for

internal communication

between the CIM 500

and the Grundfos product

9SW1

Rotary switch for

selection of industrial

Ethernet protocol

345678

English (GB)

3. Installation

3.1 Connecting the Ethernet cable

Use RJ45 plugs and Ethernet cable. Connect the

cable screen to protective earth at both ends.

Maximum cable length

Cable type

The CIM 500 is designed for flexible network

installation. The built-in two-port switch makes it

possible to daisy chain from product to product

without the need of additional Ethernet switches. The

last product in the chain is only connected to one of

the Ethernet ports. Each Ethernet port has its own

MAC address.

Fig. 2 Example of industrial Ethernet network

Fig. 3 Example of Ethernet connection

Warning

Only connect the CIM 500 to SELV or

SELV-E circuits.

Note

It is important to connect the cable screen

to earth by means of the earth clamp or in

the connector.

Note

For GRM IP communication, please

ensure the network is protected by a

firewall.

Speed

[Mbit/s] Cable type Max. cable length

[m/ft]

10 CAT5 100/328

100 CAT5e 100/328

Industrial

Ethernet

protocol

Cable type

Modbus TCP Standard CAT5, CAT5e or CAT6

PROFINET IO Standard CAT5, CAT5e or CAT6

BACnet IP Standard CAT5, CAT5e or CAT6

GRM IP Standard CAT5, CAT5e or CAT6

TM05 6435 4711

Ethernet

switch

CIM

500

CIM

500

CIM

500

CIM

500

TM05 7480 1013

Pos. Description

1 Industrial Ethernet RJ45 connector 1

2 Industrial Ethernet RJ45 connector 2

3 Earth clamp/GND

English (GB)

3.2 Selection of industrial Ethernet

protocol

The module has a rotary switch for selection of the

industrial Ethernet protocol. See fig. 4.

Fig. 4 Selecting the industrial Ethernet

protocol

3.3 Setting up the IP addresses

The module comes with fixed IP address. The IP

address settings can be changed with the built-in

web server.

3.4 Connection to the web server

The module can be configured by means of the

built-in web server. To establish a connection from a

PC to the CIM 500, proceed as follows:

1. Connect the PC and the module, using an

Ethernet cable.

2. Configure the Ethernet port of the PC to the

same network as the CIM 500, e.g.

192.168.1.101, and the subnet mask to

255.255.255.0.

See section A.1 How to configure an IP address

on your PC on page 110.

3. Open a standard Internet browser and type

192.168.1.100 in the URL field.

4. Log in to the web server:

Fig. 5 CIM 500 connected to PC

3.4.1 Connection to the web server using GRM IP

To access the web-server via GRM IP, you need to

connect your PC parallel to the router (RJ 45 port 1)

at CIM500 RJ 45 port 2 and look at Router

webserver which address the router assign to the

CIM500. Then use this IP address for the webserver

access.

See also section A.2 Web server configuration on

page 110.

TM05 7481 1013

Pos. Description

0 PROFINET IO (factory setting)

1 Modbus TCP

2 BACnet IP

3Reserved

GRM IP for Grundfos Remote

Management (requires a contract with

Grundfos)

5...E Reserved. LED1 will be permanently red

to indicate an invalid configuration.

Resetting to factory settings.

Note: Set the rotary switch to this position

for 20 seconds to reset to the factory

settings. During this period LED1 will be

flashing red and green.

Note

If the switch position is changed when the

module is powered on, the module will

restart.

Default IP

settings used by

web server

IP address: 192.168.1.100

Subnet mask: 255.255.255.0

Gateway: 192.168.1.1

IP settings for

Modbus TCP

Must be set with the web

server.

Device name and

IP settings for

PROFINET IO

Static configuration from web

server or configuration from

PROFINET IO configuration

tool

IP settings for

BACnet IP

Must be set with the web

server.

IP settings for

GRM IP

GRM IP uses DHCP, the

connected Router assigns

automatically an IP address.

Username admin (factory setting)

Password Grundfos (factory setting)

Note

Username and password may have been

changed from the factory settings.

TM05 6436 4712

Note

You can use both ETH1 and ETH2 to

establish a connection to the web server.

Note

You can access the webserver while the

selected industrial Ethernet protocol is

active.

Note

When you select "GRM IP", the connected

router will automatically assign an IP

address to the module via DHCP.

English (GB)

4. Status LEDs

The module has two status LEDs, see fig. 1:

• LED1: Red/green status LED for Ethernet

communication.

• LED2: Red/green status LED for communication

between the module and the Grundfos product.

LED1, GRM IP

LED1, Modbus TCP/BACnet IP

LED1, PROFINET IO

LED2

Status Description

Off No GRM IP communication or

switched off.

Flashing green Startup period (120 sec.)

Permanently

green

Communication with GRM server

established.

Flashing green

(0.3 Hz) Data transmitting to GRM server.

Flashing red GRM communication lost or no

communication to GRM server.

Flashing red

and green

Resetting to factory settings.

After 20 sec. the CIM 500 will

restart.

Status Description

Off No Modbus/BACnet

communication or switched off.

Flashing green Modbus/BACnet communication

active.

Permanently

red

Module configuration fault. See

section 6.1 Modbus TCP/BACnet

IP.

Permanently

red and green

Error in firmware download. See

section 6.1 Modbus TCP/BACnet

IP.

Flashing red

and green

Resetting to factory settings.

After 20 seconds the CIM 500 will

restart.

Status Description

Off The module is switched off.

Flashing green

Wink function. LED will flash 10

times when activated from

master.

Permanently

green

The module is ready for data

transmission (data exchange

state).

Flashing red (3

Hz, duty cycle

50 %)

Wrong or missing PROFINET IO

configuration. See section

6.2 PROFINET IO.

Restart the CIM 500. Use the

RESTART button from the web

server PROFINET configuration.

Pulsing red

(0.3 Hz, duty

cycle 10 %)

Configured, but connection to

master lost. See section

6.2 PROFINET IO.

Permanently

red

Product not supported. See

section 6.2 PROFINET IO.

Permanently

red and green

Error in firmware download. See

section 6.2 PROFINET IO.

Flashing red

and green

Resetting to factory settings.

After 20 seconds the CIM 500

will restart.

Status Description

Off The module is switched off.

Flashing red

No internal communication

between the CIM 500 and the

Grundfos product.

Permanently

red

The module does not support the

Grundfos product connected.

Permanently

green

Internal communication between

the module and the Grundfos

product is OK.

Permanently

red and green Memory fault.

Note

During startup, there is a delay of up to five

seconds before the status of LED1 and

LED2 is updated.

English (GB)

5. Data activity and link LEDs

The module has two connectivity LEDs related to

each RJ45 connector. See fig. 1.

DATA1 and DATA2

These yellow LEDs indicate data traffic activity.

LINK1 and LINK2

These green LEDs show whether the Ethernet cable

is properly connected.

Status Description

Off No data communication on RJ45

connector

Flashing Data communication on RJ45

connector

On Heavy network traffic

Status Description

Off No Ethernet link on RJ45 connector

On Ethernet link on RJ45 connector is OK

English (GB)

6. Fault finding

6.1 Modbus TCP/BACnet IP

You can detect faults in a module by observing the

status of the two status LEDs. See the tables below.

CIM 500 fitted in a Grundfos product

Fault (LED status) Possible cause Remedy

1. Both LEDs remain off when

the power supply is

connected.

a) The module is fitted

incorrectly in the Grundfos

product.

Check that the module is

fitted/connected correctly.

b) The module is defective. Replace the module.

2. LED2 is flashing red. a) No internal communication

between the module and the

Grundfos product.

Check that the module is fitted

correctly.

3. LED2 is permanently red. a) The module does not support

the Grundfos product

connected.

Contact the nearest Grundfos

company.

4. LED1 is permanently red. a) Fault in the Modbus/BACnet

configuration of the module.

Modbus: Check that SW1 is set to

"1". Check that the Modbus IP

address configuration is correct.

See section A.4 Modbus TCP

configuration on page 112.

BACnet: Check that SW1 is set to

"2". Check that the BACnet IP

address configuration is correct.

See section A.5 BACnet IP

configuration on page 113.

5. LED1 is permanently red and

green at the same time.

a) Error in firmware download. Use the web server to download

the firmware again. See section

A.13 Update on page 121.

6. LED2 is permanently red and

green at the same time.

a) Memory fault. Replace the module.

Otros manuales para CIM 500

Tabla de contenidos

Idiomas:

Otros manuales de Unidad de control de Grundfos

Grundfos

Grundfos SA-SPM Manual de usuario

Grundfos

Grundfos PM 1 Manual de usuario

Grundfos

Grundfos ALPHA1 B Manual de usuario

Grundfos

Grundfos MC 40/60 Manual de usuario

Grundfos

Grundfos LC 241 Manual de usuario

Grundfos

Grundfos IO 112 Manual de usuario

Grundfos

Grundfos DID Series Manual de usuario

Grundfos

Grundfos CIM 500 Manual de usuario

Grundfos

Grundfos PM 1 Manual de usuario

Grundfos

Grundfos CIM 500 Manual de usuario

Grundfos

Grundfos CIM 500 Manual de usuario

Grundfos

Grundfos OHJEET CIM 500 Manual de usuario

Grundfos

Grundfos MFV Manual de usuario

Grundfos

Grundfos MC 80 Manual de usuario

Grundfos

Grundfos CIM 200 Manual de usuario

Grundfos

Grundfos CIM 3 Series Manual de usuario

Grundfos

Grundfos Unilift AP12 Manual de usuario

Grundfos

Grundfos CU 401 Manual de usuario

Grundfos

Grundfos DIT-IR Manual de usuario

Grundfos

Grundfos MAGNA 2000 Series Manual de usuario

Grundfos

Grundfos CU 242 Manual de usuario

Grundfos

Grundfos RSL Manual de usuario

Grundfos

Grundfos CIM 260 Manual de usuario

Grundfos

Grundfos CU 401 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario