Greenlee PDMM-10 Manual de usuario

PDMM-10

DIGITAL

MULTIMETER

MULTÍMETRO

DIGITAL

MULTIMETRE

NUMERIQUE

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Read and understand all of the instructions

and safety information in this manual

before operating or servicing this tool.

Lea y entienda todas las instrucciones y la

información sobre seguridad que aparecen

en este manual, antes de manejar esta

herramienta o darle mantenimiento.

Lire attentivement et bien comprendre

toutes les instructions et les informations

sur la sécurité de ce manuel avant d‘utiliser

ou de procéder à l‘entretien de cet outil.

Description

The Greenlee PDMM-10 Digital Multimeter is a hand-held testing

device with the following measurement capabilities: AC and DC

voltage, DC current, and resistance. It also checks diodes and

verifies continuity.

Specialized functions and capabilities include:

• Digital display (LCD)

• Manual range selection

• Voltage measurements up to 300 V AC/DC

• Current measurements up to 200 mA DC

• Resistance measurements up to 2 MΩ

• Diode/continuity test

• Attached test leads

Safety

Safety is essential in the use and maintenance of Greenlee tools

and equipment. This instruction manual and any markings on the

tool provide information for avoiding hazards and unsafe practices

related to the use of this tool. Observe all of the safety information

provided.

Purpose

This instruction manual is intended to familiarize all personnel with

the safe operation and maintenance procedures for the Greenlee

PDMM-10 Digital Multimeter.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge.

Greenlee and are registered trademarks of Greenlee Textron.

KEEP THIS MANUAL

PDMM-10

Important Safety Information

This symbol is used to call your attention to hazards or unsafe

practices which could result in an injury or property damage.

The signal word, defined below, indicates the severity of the

hazard. The message after the signal word provides informa-

tion for preventing or avoiding the hazard.

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in

severe injury or death.

Hazards which, if not avoided, COULD result in severe injury

or death.

Hazards or unsafe practices which, if not avoided, MAY result

in injury or property damage.

Read and understand this material

before operating or servicing

this equipment. Failure to understand

how to safely operate this tool can result

in an accident causing serious injury or

death.

Important Safety Information

Electric shock hazard:

Contact with live circuits can result in

severe injury or death.

Electric shock and fire hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Inspect the test leads before use. They must be clean and

dry, and the insulation must be in good condition.

• Use this unit for the manufacturer’s intended purpose only,

as described in this manual. Any other use can impair the

protection provided by the unit.

Failure to observe these warnings can result in severe injury or

death.

Electric shock hazard:

• Do not apply more than the rated voltage between any two

input terminals, or between any input terminal and earth

ground.

• Do not contact the test lead tips or any uninsulated portion

of the accessory.

Failure to observe these warnings can result in severe injury or

death.

PDMM-10

Important Safety Information

Do not change the measurement function or range while the

test leads are connected to a component or circuit.

Failure to observe this precaution can result in injury and can

damage the unit.

The fuse is an integral part of the overvoltage protection.

When fuse replacement is necessary, see Specifications for the

correct type, size, and capacity. Using any other type of fuse

will void the overvoltage protection rating of the unit.

Failure to observe this warning can result in severe injury or

death.

• Do not operate with the case open.

• Before opening the case, remove the test leads from the

circuit and shut off the unit.

Failure to observe these warnings can result in severe injury or

death.

Important Safety Information

• Unless measuring voltage or current, shut off and lock out

power. Make sure that all capacitors are discharged. Voltage

must not be present.

• Set the selector and connect the test leads so that they

correspond to the intended measurement. Incorrect settings

or connections can result in a blown fuse.

• Using this unit near equipment that generates electromag-

netic interference can result in unstable or inaccurate

readings.

• Do not attempt to repair this unit. It contains no user-

serviceable parts.

• Do not expose the unit to extremes in temperature or high

humidity. See Specifications.

Failure to observe these precautions can result in injury and

can damage the unit.

PDMM-10

Identification

1. Digital display (LCD)

2. Function selector

3. Power and measurement range selector

4. Test leads with probes

Using the Features

Power and measurement range selector: Slide the selector up to

turn unit on. Line the selector up with desired settings. Always

start with highest setting. Slide the selector down to turn unit off.

Function selector: Slide the selector side to side to set the proper

position prior to connecting the test probes. Disconnect the

probes from the circuit or component before switching to a new

function.

Test leads: Red probe polarity is positive. Remove test lead caps

to perform tests.

Operation

Electric shock hazard:

Contact with live circuits can result in

severe injury or death.

1. See the Settings Table. Set the measurement range selector to

the proper setting, starting with the highest measurement

setting. Never apply more than 300 V to the unit.

2. See Typical Measurements for specific measurement

instructions.

3. Test the unit on a known functioning circuit or component.

• If the unit does not function as expected on a known

functioning circuit, replace the battery and/or fuse.

• If the unit still does not function as expected, send the unit

to Greenlee for repair. See the address shown under

Warranty.

4. Take the reading from the circuit or component to be tested. If

the resolution is not satisfactory, remove the meter from the

circuit and change to the next lower range.

Settings Table

To measure set the function

this … selector to this Notes

symbol …

AC Voltage

(300 V max)

DC Voltage

(300 V max)

DC Current Connect in series and turn on circuit

(250 V and or component.

200 mA max)

Resistance Make sure circuit or component is

turned off and no voltage is present.

• Make sure circuit or component is

turned off and no voltage is present.

Diode/ Polarity of red probe is +.

Continuity • Range selector must be in the

2k position.

• Tone indicates continuity.

PDMM-10

Typical Measurements

Voltage Measurement

Current Measurement

Resistance Measurement

Continuity Check

Typical Measurements

Tabla de contenidos

Idiomas:

Otros manuales de Multímetro de Greenlee

Greenlee

Greenlee 93-105 Manual de usuario

Greenlee

Greenlee DM-70 Manual de usuario

Greenlee

Greenlee DM-60 Manual de usuario

Greenlee

Greenlee CMT-80 Manual de usuario

Greenlee

Greenlee CM-1500 Manual de usuario

Greenlee

Greenlee DM-860A Manual de usuario

Greenlee

Greenlee SDMM-1 Manual de usuario

Greenlee

Greenlee CM-750 Manual de usuario

Greenlee

Greenlee CM-400 Manual de usuario

Greenlee

Greenlee CM-330 Manual de usuario

Greenlee

Greenlee CM-1000 Manual de usuario

Greenlee

Greenlee CMI-100 Manual de usuario

Greenlee

Greenlee DM-200 Manual de usuario

Greenlee

Greenlee CMT-60 Manual de usuario

Greenlee

Greenlee PDMM-20 Manual de usuario

Greenlee

Greenlee CMP-200 Manual de usuario

Greenlee

Greenlee CMI-200 Manual de usuario

Greenlee

Greenlee DM-200A Manual de usuario

Greenlee

Greenlee DM-25 Manual de usuario

Greenlee

Greenlee 93-97 Manual de usuario

Greenlee

Greenlee CM-1050 Manual de usuario

Greenlee

Greenlee DM-500 Manual de usuario

Greenlee

Greenlee GRDM-45 Manual de usuario

Greenlee

Greenlee 93-502 Manual de usuario

Manuales populares de Multímetro de otras marcas

Agilent Technologies

Agilent Technologies 34420A Manual de usuario

Fluke

Fluke 83 Manual de usuario

Hameg

Hameg HM 8012 Manual de usuario

Mastech

Mastech MY70 Manual de usuario

Steren

Steren MUL-300 Manual de usuario

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manual de usuario

PeakTech

PeakTech 4000 Manual de uso y cuidado

YOKOGAWA

YOKOGAWA 90050B Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manual de usuario

Fluke

Fluke 8846A Manual de operación y mantenimiento

Tempo Communications

Tempo Communications MM200 Manual de usuario

Elenco Electronics

Elenco Electronics CM-1555 Manual de usuario

Mastech

Mastech MS8238C Manual de usuario

SDAR

SDAR 830A, 830B, 830D, 830C Manual de usuario

RS PRO

RS PRO RS-9519BT Manual de usuario

BGS technic

BGS technic 8890 Manual de usuario

Amprobe

Amprobe Hexagon 60 Manual de usuario