Greenlee DM-200 Manual de usuario

DM-200 • DM-210

DIGITAL

MULTIMETERS

MULTÍMETROS

DIGITALES

MULTIMETRES

NUMERIQUES

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Read and understand all of the instructions and safety

information in this manual before operating or servicing this tool.

Lea y entienda todas las instrucciones y la información sobre

seguridad que aparecen en este manual, antes de manejar estas

herramientas o darles mantenimiento.

Lire attentivement et bien comprendre toutes les instructions et

les informations sur la sécurité de ce manuel avant d’utiliser ou de

procéder à l’entretien de cet outil.

Description

The Greenlee DM-200 and DM-210 Digital Multimeters are hand-held testing devices

with the following measurement capabilities: AC and DC voltage, AC and DC current and

resistance. They also check diodes, verify continuity and detect electric fields. In addition, the

DM-210 measures temperature (K-type thermocouples only), frequency and capacitance.

Safety

Safety is essential in the use and maintenance of Greenlee tools and equipment. This

instruction manual and any markings on the tool provide information for avoiding hazards and

unsafe practices related to the use of this tool. Observe all of the safety information provided.

Purpose

This instruction manual is intended to familiarize all personnel with the safe operation and

maintenance procedures for the Greenlee DM-200 and DM-210 Digital Multimeters.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge.

and are registered trademarks of Greenlee Textron.

KEEP THIS MANUAL

DM-200 • DM-210

Important Safety Information

This symbol is used to call your attention to hazards or unsafe practices which could

result in an injury or property damage. The signal word, defined below, indicates the

severity of the hazard. The message after the signal word provides information for

preventing or avoiding the hazard.

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in severe injury or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury or property

damage.

Read and understand this material before operating or servicing

this equipment. Failure to understand how to safely operate this

tool can result in an accident causing serious injury or death.

Electric shock hazard:

Contact with live circuits can result in severe injury or death.

Important Safety Information

Electric shock hazard:

• Do not apply more than the rated voltage between any two input terminals, or

between any input terminal and earth ground.

• Do not contact the test lead tips or any uninsulated portion of the accessory.

Failure to observe these warnings can result in severe injury or death.

• Do not operate with the case open.

• Before opening the case, remove the test leads from the circuit and shut off the unit.

Failure to observe these warnings can result in severe injury or death.

Electric shock and fire hazard:

• Do not expose this unit to rain or moisture.

• Use this unit for the manufacturer’s intended purpose only, as described in this

manual. Any other use can impair the protection provided by the unit.

Failure to observe these warnings can result in severe injury or death.

Electric shock hazard:

• Do not use the unit if it is wet or damaged.

• Use test leads or accessories that are appropriate for the application. See the

category and voltage rating of the test lead or accessory.

• Inspect the test leads or accessory before use. The item(s) must be clean and dry,

and the insulation must be in good condition.

Failure to observe these warnings can result in severe injury or death.

DM-200 • DM-210

Important Safety Information

Do not change the measurement function while the test leads are connected to a

component or circuit.

Failure to observe this precaution can result in injury and can damage the unit.

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity.

See Specifications.

Failure to observe these precautions can result in injury and can damage the unit.

Unless measuring voltage, current or frequency, shut off and lock out power. Make

sure that all capacitors are discharged. Voltage must not be present.

The fuse is an integral part of the overvoltage protection. When fuse replacement is

necessary, see Specifications for the correct type, size and capacity. Using any other

type of fuse will void the overvoltage protection rating of the unit.

Failure to observe this warning can result in severe injury or death.

Set the selector and connect the test leads so that they correspond to the intended

measurement. Incorrect settings or connections can result in a blown fuse.

Using this unit near equipment that generates electromagnetic interference can result

in unstable or inaccurate readings.

Identification

1. Display 3-2/3–digit LCD (2499 maximum display)

2. Feature Buttons See explanations under Using the Features

3. Selector Selects a function or turns power OFF

4. APositive input terminal for high current measurements

5. mA µAPositive input terminal for low current and temperature

measurements*

6. COM Negative, common or ground input terminal for all measurements

7. +Positive input terminal for all measurements

except

current

and temperature*

* DM-210 only

DM-200 • DM-210

Display Icons

8. Automatic Ranging is enabled.

9. DC measurement is selected.

10. AC measurement is selected.

11. – Polarity Indicator

12. OL Overload (numeric display)

13. Diode

14. Continuity

15. Hold function is enabled.

16. Low Battery

17. ∆Relative Zero function is enabled.

18. k Kilo (103)

Symbols on Unit

Read the instruction manual.

Double Insulation

19. M Mega (106)

20. ΩOhms

21. Hz Hertz (frequency in

cycles per second)

22. n Nano (10-9)

23. % Percent

24. µMicro (10-6)

25. m Milli (10-3)

26. F Farads

27. V Volts

28. A Amps

29. RS 232 Optional PC interface

is active

9–10 15–16

18–21

22–23

24–28

1329 14

Using the Features

• Automatic Power Off To extend battery life, the meter will shut itself off after approximately

30 minutes of inactivity. To restore power, press any button. To disable this feature, press

Select while turning the meter on.

•Select Press momentarily to toggle between functions, or to toggle between AC and DC

when measuring current and volts.

• Range Press once to enter the manual ranging mode. The icon will disappear from

the display. Press repeatedly to step through the ranges. Press and hold to return to the

automatic ranging mode.

• Hz % (DM-210 only) Press momentarily when performing any measurement to display the

frequency. Press again to display the duty cycle as a percentage (%). Press again to exit

this mode.

Note: The sensitivity of the frequency measurement function varies with the measurement

range. To automatically select a sensitivity level, measure the voltage level first, then press

. If the reading becomes unstable, or if the display is blank, manually change the

sensitivity by momentarily pressing

Range.

• DET Press to use the AC Detective technology. Use this feature to detect the electric field

that surrounds current-carrying conductors. Signal strength is displayed as a series of

dashes on the display.

• Use the multimeter’s built-in antenna (located along the top, near the LCD) for tracing

live circuits or locating a break in a wire.

• For more precision, such as distinguishing between current-carrying and ground wires,

connect a test lead to the + input terminal and use it as a probe.

• Relative ∆(DM-210 only) Finds the difference between two measurements. While taking a

measurement, press Rel ∆to set the display to zero. The ∆icon will appear on the display.

Take the second measurement. The value on the display will be the difference between the

two measurements. Press and hold to exit this mode.

• Hold Press momentarily to hold the present value on the display. Press again to exit this

mode.

DM-200 • DM-210

Operation

1. See the Settings Table. Set the selector to the proper setting, press Select (when

instructed to do so), and connect the test leads to the meter.

2. See Typical Measurements for specific measurement instructions.

3. Test the unit on a known functioning circuit or component.

• If the unit does not function as expected on a known functioning circuit, replace the

batteries and/or fuses.

• If the unit still does not function as expected, send the unit to Greenlee for repair.

4. Take the reading from the circuit or component to be tested.

Electric shock hazard:

Contact with live circuits can result in severe injury or death.

To measure set the selector this icon will connect and connect

this value … to this symbol … appear on the red the black

the display … lead to … lead to …

Capacitance* ***

(DM-210 only) ΩF + COM

and press Select 3 times

***

Continuity** Ω+ COM

and press Select twice

Current (10 A max) AA A COM

Current mA mA µACOM

(100 mA max) mA

Current µAµAµACOM

(100 µA max) mA

DET Any function and +

(electric field press DET EF (optional) N/A

detection) momentarily

***

Diode Ω+ COM

and press Select

Any function and Hz

Frequency press and hold Hz

(DM-210 only) press Hz again to measure %

frequency as a duty cycle

Resistance *** Ω+ COM

Ω

Voltage VV + COM

Temperature

in degrees Farenheit K-Temp and the µACOM

(DM-210 only) temperature in mA

degrees Farenheit

Settings Table

* Discharge capacitor before measurement.

** Tone indicates continuity. The threshold is between 20 Ωand 150 Ω.

*** Capacitance symbol on DM-210 only.

COM

Otros manuales para DM-200

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Multímetro de Greenlee

Greenlee

Greenlee DM-200A Manual de usuario

Greenlee

Greenlee CM-1100 Manual de usuario

Greenlee

Greenlee DM-800 Manual de usuario

Greenlee

Greenlee 93-604 Manual de usuario

Greenlee

Greenlee CM-410 Manual de usuario

Greenlee

Greenlee 93-502 Manual de usuario

Greenlee

Greenlee CM-600 Manual de usuario

Greenlee

Greenlee CMPL-100 Manual de usuario

Greenlee

Greenlee DM-45 Manual de usuario

Greenlee

Greenlee 93-500 Manual de usuario

Greenlee

Greenlee CM-1200 Manual de usuario

Greenlee

Greenlee DM-500 Manual de usuario

Greenlee

Greenlee CM-450 Manual de usuario

Greenlee

Greenlee CM-330 Manual de usuario

Greenlee

Greenlee DM-860A Manual de usuario

Greenlee

Greenlee DM-50 Manual de usuario

Greenlee

Greenlee DM-20 Manual de usuario

Greenlee

Greenlee DM-200 Manual de usuario

Greenlee

Greenlee CM-400 Manual de usuario

Greenlee

Greenlee DM-60 Manual de usuario

Greenlee

Greenlee CM-1500 Manual de usuario

Greenlee

Greenlee CM-1300 Manual de usuario

Greenlee

Greenlee 93-603 Guía del usuario

Greenlee

Greenlee DM-45 Manual de usuario

Manuales populares de Multímetro de otras marcas

Agilent Technologies

Agilent Technologies 34420A Manual de usuario

Fluke

Fluke 83 Manual de usuario

Hameg

Hameg HM 8012 Manual de usuario

Mastech

Mastech MY70 Manual de usuario

Steren

Steren MUL-300 Manual de usuario

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manual de usuario

PeakTech

PeakTech 4000 Manual de uso y cuidado

YOKOGAWA

YOKOGAWA 90050B Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manual de usuario

Fluke

Fluke 8846A Manual de operación y mantenimiento

Tempo Communications

Tempo Communications MM200 Manual de usuario

Elenco Electronics

Elenco Electronics CM-1555 Manual de usuario

Mastech

Mastech MS8238C Manual de usuario

SDAR

SDAR 830A, 830B, 830D, 830C Manual de usuario

RS PRO

RS PRO RS-9519BT Manual de usuario

BGS technic

BGS technic 8890 Manual de usuario

Amprobe

Amprobe Hexagon 60 Manual de usuario