Greenlee 5990A Manual de usuario

Read and understand all of the instructions and safety information in this

manual before operating or servicing this tool.

INSTRUCTION MANUAL

5990A

Megohmmeter

www. .com information@itm.com1.800.561.8187

Table of Contents

Description .............................................................................................. 3

Safety ...................................................................................................... 3

Purpose.................................................................................................... 3

Important Safety Information............................................................... 4–6

Identiﬁcation.......................................................................................7-11

LC Display ......................................................................................... 7

Operator’s Panel................................................................................ 8

Connectors.................................................................................. 9–10

High Voltage Shielded Test Tips with High Voltage Alligator Clips... 11

Performing Measurements.............................................................. 12–13

Measurements................................................................................. 14–18

General Information About DC High Voltage Testing........................ 14

Guard Terminal................................................................................ 15

Insulation Resistance Measurement......................................... 16–17

Voltage Measurement ..................................................................... 18

Maintenance.................................................................................... 19–21

Speciﬁcations................................................................................. 22–23

Accuracy ......................................................................................... 22

Measurements ................................................................................ 22

Insulation Resistance...................................................................... 22

General Capability vs Resistance.................................................... 23

Voltage ............................................................................................ 23

General Speciﬁcations........................................................................... 24

Measurement Categories ...................................................................... 25

Statement of Conformity ....................................................................... 25

www. .com information@itm.com1.800.561.8187

5990A

Description

The Greenlee 5990A Megohmmeter is intended to test insulation and detect voltage. The unit

features an easy-to-read and accurate analog scale.

Safety

Safety is essential in the use and maintenance of Greenlee tools and equipment. This instruc-

tion manual and any markings on the tool provide information for avoiding hazards and unsafe

practices related to the use of this tool. Observe all of the safety information provided.

Purpose

This instruction manual is intended to familiarize all personnel with the safe operation and

maintenance procedures for Greenlee 5990A Megohmmeter.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge.

Greenlee and are registered trademarks of Greenlee Tools, Inc.

Do not discard this product or throw away!

All speciﬁcations are nominal and may change as design improvements occur. Greenlee Tools, Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

® Registered: The color green for electrical test instruments is a registered trademark of Greenlee Tools, Inc.

KEEP THIS MANUAL

www. .com information@itm.com1.800.561.8187

Important Safety Information

Read and understand this material before operating or servicing this

equipment. Failure to understand how to safely operate this tool can

result in an accident causing serious injury or death.

This symbol is used to call your attention to hazards or unsafe practices which could

result in an injury or property damage. The signal word, deﬁned below, indicates the

severity of the hazard. The message after the signal word provides information for

preventing or avoiding the hazard.

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in severe injury or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury or

property damage.

Electric shock hazard:

Contact with live circuits can result in severe injury or death.

www. .com information@itm.com1.800.561.8187

5990A

Important Safety Information

Electric shock and ﬁre hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Use test leads or accessories that are appropriate for the application. See the category and

voltage rating of the test lead or accessory.

• Inspect the test leads before use. They must be clean and dry, and the insulation must be in

good condition.

• Use this unit for the manufacturer’s intended purpose only, as described in this manual.

Anyotheruse can impair the protection provided by the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not apply more than the rated voltage between any two input terminals, or between any

input terminal and earth ground.

• Do not contact the test lead tips or any uninsulated portion of the accessory.

• Do not contact the test lead tips while performing the insulation resistance test.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not operate with the case open.

• Before opening the case, remove the test leads from the circuit and shut off the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Unless measuring voltage, shut off and lock out power. Make sure that all capacitors are

discharged. Voltage must not be present.

• Using this unit near equipment that generates electromagnetic interference can result in

unstable or inaccurate readings.

Failure to observe these warnings could result in severe injury or death.

www. .com information@itm.com1.800.561.8187

Working with the instrument:

• Equipment under test must be switched off (i.e. de-energized) before test leads are con-

nected to the equipment.

• Do not touch any conductive parts of equipment under test during the test.

• Make sure that the tested object is disconnected (mains voltage disconnected) before start-

ing the Insulation Resistance measurement!

• Do not touch the tested object whilst testing it, risk of electric shock!

• In case of a capacitive test object (long tested cable etc.), automatic discharge of the object

may not be done immediately after ﬁnishing the measurement – “Please wait, discharging”

message will be displayed.

Handling with capacitive loads:

• Note that 40 nF charged to 1 kV or 9 nF charged to 5 kV are hazardous live!

• Never touch the measured object during the testing until it is totally discharged.

• Maximum external voltage between any two leads is 600 V (CAT IV environment).

Important Safety Information

Electric shock hazard:

Contact with live circuits can result in severe injury or death.

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity. See Speciﬁcations.

Failure to observe these precautions may result in injury and can damage the unit.

www. .com information@itm.com1.800.561.8187

5990A

Instrument Description

Instrument Casing

The instrument is housed in a plastic box that maintains the protection class deﬁned in the

general speciﬁcations.

LCD

The LCD has a backlight and offers easy-to-read results. See Fig.1 below.

Legend:

1.......... Battery indicator: This indicates condition of the battery. In battery charging mode it ﬂashes.

2.......... Hazardous Voltage Warning icon: This indicates that voltage higher than 70 V may be

present at the test terminals!

3.......... Analog display

4.......... Auxiliary digital display

5.......... Auxiliary units

6.......... Analog units

7.......... Bar graph

8.......... Warning icon: Carefully read and understand the User Manual.

9.......... Pass or Fail icon

10........ Main units

11........ Main digital display

12........ Test voltage: Menu for selecting the test voltage.

Fig. 1 LCD Display

www. .com information@itm.com1.800.561.8187

5990A Megohmmeter

5990A

52085064 REV1

The operator’s panel is shown in Fig. 2 below.

Legend:

1...........Ω: Press to switch to Insulation Measurement Mode. Press again to set a resistance

limit value.

2.......... V: Press to switch to Voltage measurement mode.

3.......... Light:Press to to turn the display backlight ON or OFF.

4.......... tcursor: Press to decrease the test voltage parameter or resistance limit value.

5.......... ucursor: Press to increase the test voltage parameter or resistance limit value.

6.......... START/STOP: Press to start or stop insulation measurement.

7.......... ON/OFF: Press to switch the instrument ON or OFF.

Fig. 2. Front Panel

Operator’s Panel

Instrument Description (cont’d)

LCD

Keypad4 5

www. .com information@itm.com1.800.561.8187

5990A

The 5990A Tester contains the following connections:

• Four banana safety sockets for test leads (Fig. 3).

• Socket for mains supply cable (Fig. 4).

Fig. 3 Test Leads Connector Diagram

Connectors

1.......... (-OUT): Negative Insulation Resistance test terminal

2.......... GUARD: Guard terminals are intended to lead away potential leakage current while

measuring the Insulation. Both green sockets are connected together inside of

the instrument.

3.......... (+OUT): Positive Insulation Resistance test terminal

Use original test accessories only!

Max allowed external voltage between test terminals and ground is 600V!

Max allowed external voltage between test terminals is 600V!

Instrument Description (cont’d)

1 2 3

www. .com information@itm.com1.800.561.8187

Fig. 4. Mains connector

Fig. 4 Mains Connector

Connectors (cont’d)

1..........Mains connector: This is to connect the instrument to the mains supply.

Use original mains supply cable only!

Instrument Description (cont’d)

www. .com information@itm.com1.800.561.8187

Otros manuales para 5990A

Tabla de contenidos

Otros manuales de Instrumento de medición de Greenlee

Greenlee

Greenlee 5990 Manual de usuario

Greenlee

Greenlee Pull Connect Manual de usuario

Greenlee

Greenlee DataScout 10G Manual de usuario

Greenlee

Greenlee IPM-400 Manual de usuario

Greenlee

Greenlee 200EP-G Manual de usuario

Greenlee

Greenlee 5990A Manual de usuario

Greenlee

Greenlee AM-600T Manual de usuario

Greenlee

Greenlee 93-808 Guía

Greenlee

Greenlee 200B-G Manual de usuario

Greenlee

Greenlee 93-172 Manual de usuario

Greenlee

Greenlee BLL-200 Manual de usuario

Greenlee

Greenlee FG01 G-Series Smart Pull Manual de usuario

Greenlee

Greenlee 93-172 Manual de usuario

Greenlee

Greenlee TM-400 Manual de usuario

Greenlee

Greenlee 5990A-C Manual de usuario

Greenlee

Greenlee CSJ-100 Manual de usuario

Greenlee

Greenlee 5124 Manual de usuario

Greenlee

Greenlee AirScout Gigacheck Manual de usuario

Greenlee

Greenlee CMF-110 Manual de usuario

Greenlee

Greenlee 500XP Manual de usuario

Greenlee

Greenlee 200fp Manual de usuario

Greenlee

Greenlee CS-8000 Circuit Seeker Manual de usuario

Greenlee

Greenlee 93-804 Guía

Greenlee

Greenlee HCO-100 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario