GRASS VALLEY SHDSDA1 Manual de instalación

SHDSDA1 OPERATION

System HD Eight Output HD-SDI Distribution

Amplifier Operation Manual

SHDSDA1 Version 1 Issue 3 030402 1

CONTENTS

INTRODUCTION TO THIS OPERATION

MANUAL................................................................2

SCOPE OF THIS OPERATION MANUAL.............3

MODULE DESCRIPTION .................................3

FEATURES............................................................4

TECHNICAL PROFILE..........................................5

INPUT................................................................5

OUTPUTS.........................................................5

INDICATOR LEDS............................................5

Standard.......................................................5

Enhanced.....................................................5

ROLLCALL.....................................................5

OPTIONS..........................................................5

REAR INTERFACE CONNECTIONS....................7

REAR INTERFACE NOTATION GUIDE...........7

STANDARD INPUT...........................................7

STANDARD OUTPUTS ....................................7

ROLLCALL MENU SYSTEM.................................8

ROLLCALL MONITORING FEATURES...............9

SHDSDA1 OPERATION

SHDSDA1 Version 1 Issue 3 030402 2

Introduction to this Operation Manual

This manual covers the operation and use of the module described below.

WARNING…

THE FRONT PANEL OF THE UNIT MUST NOT BE

OPENED BY THE OPERATOR. ACCESS IS ONLY

PERMITTED TO FULLY QUALIFIED

INSTALLATION ENGINEERS.

System HD Modules must only be installed and/or replaced by qualified service personnel, with reference to

the System HD Installation guide. Refer all installation and servicing to qualified personnel only.

Manufacturers Notice

allowed by statutory or judicial law or hereinafter granted, including without limitation, material generated from

the software programs which are displayed on the screen such as icons, screen display looks etc.

Reproduction or disassembly of embedded computer programs or algorithms is prohibited.

No part of this publication may be transmitted or reproduced in any form or by any means, electronic or

mechanical, including photocopy, recording or any information storage and retrieval system, without permission

being granted, in writing, by the publishers or their authorised agents.

Important Notice

No responsibility is taken by the manufacturer or supplier for any non-compliance to EMC standards due to

incorrect installation.

Information in this manual and software are subject to change without notice and does not represent a

commitment on the part of Snell & Wilcox Ltd. The software described in this manual is furnished under a

licence agreement and may not be reproduced or copied in any manner without prior agreement with Snell &

Wilcox Ltd. or their authorised agents.

SHDSDA1 OPERATION

SHDSDA1 Version 1 Issue 3 030402 3

Scope of this Operation Manual

This is the operation manual for the System HD Single Channel Distribution Amplifier Module. It covers the

modules ordered under the following codes :

SHDSDA1S-S1 – Standard 8 output distribution amplifier with basic reporting.

SHDSDA1E-S1 – 8 output distribution amplifier with enhanced reporting

SHDSDA1S-S1 and SHDSDA1E-S1 Distribution Amplifier, Rear Panel View

Module Description

The Eight Output HD-SDI Distribution Amplifier

provides eight reclocked HD-SDI outputs from a

single HD-SDI input.

The electrical high definition serial digital (HD-SDI)

bitstream is input into the distribution amplifier main

board via a 75ΩBNC connector on a rear panel

interface card. The HD-SDI input signal is then

equalised and re-clocked before being split to

provide eight identical coaxial HD-SDI outputs for

the user via 75ΩBNC connectors on the backpanel

of the interface card.

Detailed performance information can be obtained

via the RollCall interface.

Two levels of monitoring sophistication are

available to the user. A standard operational level

is available on all boards, covering parameters

ranging from voltage supply status to the presence

of an input signal. The optional enhanced

monitoring level provides a comprehensive

analysis of the incoming HD-SDI signal such as

CRC error detection, line standard and frame rate

identification.

WARNING…

THE FRONT PANEL OF THE UNIT MUST NOT

BE OPENED BY THE OPERATOR. ACCESS IS

ONLY PERMITTED TO FULLY QUALIFIED

INSTALLATION ENGINEERS.

It is recommended that a record is made of the

System HD Order Code for the module in the table

on the following page. This will allow easy

identification of the monitoring level of the main

board when referring to this manual at a later date.

Quick guide to order codes:

SHD SDA1 XS X

Dist. Amplifier

Code Properties

SStandard reporting

EEnhanced reporting

Interface card

option code Interface card supplied with

main amplifier board

110 BNC labelled for 8 output

Codes other than those listed refer to custom

options.

Amplifier

card

Interface

card

SHDSDA1 OPERATION

SHDSDA1 Version 1 Issue 3 030402 4

Features

nSMPTE292M 1.485Gbit/s HD-SDI data rate

supported

nEight equalised and reclocked HD-SDI data

outputs

nCan equalise over 100m of cable

nAlarm functions for poor quality input signals

and device malfunction

nStand-alone or RollCall operation

nIncoming signal analysis available as an

option, it includes:

CRC status

Line standard

Frame Rate

Error rate

Note:

RollCallTM enabled for remote system control &

monitoring.

SHDSDA1 OPERATION

SHDSDA1 Version 1 Issue 3 030402 5

Technical Profile

INPUT

Electrical 1.485GBit/s HD-SDI

Connector Format BNC 75ohm panel jack

Input Cable Length 100m

Peak-to-peak

signal amplitude 800mV ±10%

D.C. offset 0V ±0.5V

Rise time (20-80%)

Fall time (20-80%)

Difference

< 270ps

≤100ps

Return loss >15dB

OUTPUTS

Electrical 1.485Gbit/s HD-SDI

Connector Format BNC 75ohm panel jack

Outputs 8

Peak-to-peak

signal amplitude 800mV ±10%

D.C. offset 0V ±0.5V

Rise time (20-80%)

Fall time (20-80%)

Difference

< 270ps

≤100ps

Return loss >15dB

INDICATOR LEDS

Not available to the Operator

Standard

Power Power supplies valid

Fault Board fault

Enhanced Monitoring Option

CPU Valid CPU activity

PLL Lock Output locked to input

standard

CRC Error Data error

Line Indicates line standard

Frame Indicates frame rate

Prog/Int Indicates progressive or

interlaced frames

RollCall™

‘Standard’ RollCall

monitoring options: General alarm

Supply voltage levels

Board temperature

‘Enhanced’ RollCall

monitoring options: CRC status

Line standard

Frame rate

Error rate

POWER CODE 1

WEIGHT <750gm (Main Board plus

Interface Board)

OPTIONS See page 2

SHDSDA1 OPERATION

SHDSDA1 Version 1 Issue 3 030402 6

Notes…

1. The eight output HD-SDI distribution

amplifier (DA) is available with two levels of

monitoring sophistication. A standard

option which provides board level

information such as supply faults and

minimum incoming signal analysis. The

enhanced monitoring option adds a

comprehensive incoming signal analysis

capability, including the detection of CRC

errors and identification of the line

standard/frame rate of the signal being

distributed. Refer to the monitor option code

on page 2 to identify what monitoring level

is fitted to the DA board.

2. The interface card for the single channel

eight output DA contains ten BNC

connectors (see following page for

drawing) of which only nine are actually

required for full operation (one IN, eight

OUT), the middle BNC not being used. A

dual channel version of the DA card is also

available (order number SHD_SDA2x S2)

which contains two separate four output

amplifiers. A dual channel DA also has a 10

BNC rear interface card (two lots of 1 IN,

four OUT). The only difference between the

rear interface cards for the two types of DA

is in the backpanel labelling. Mechanically

these two different types of rear interface

card are completely compatible with each

other and can be interchanged between the

different types of DA board. Refer to the

interface card option code on page 2 to

identify what interface card has been

supplied with the eight output DA main

board.

CAUTION: Confusion could arise if

single/double channel rear interface cards are

assigned to the wrong type of DA board.

Though full functionality will be maintained for

both types of DA, the difference in labelling

could be misleading if all such occurrences are

not fully documented at a system level.

SHDSDA1 OPERATION

SHDSDA1 Version 1 Issue 3 030402 7

Rear Interface Connections

Rear Interface Notation Guide

Electrical HD-SDI Input

A High Definition Serial Digital electrical input

though a 75ΩBNC connector is denoted in the way

shown opposite. The “ H ” denotes the High

Definition element and the “ n” is the connection

number for that particular rear interface.

Electrical HD-SDI Output

A High Definition Serial Digital electrical output

though a 75ΩBNC connector is denoted in the way

shown opposite. The “ H ” denotes the High

Definition element and the “ n” is the connection

number for that particular rear interface.

Standard Input

Electrical HD-SDI

Used On : SHDSDA1S-S1

SHDSDA1E-S1

The high definition serial digital electrical input is

connected to a 75ΩBNC connector. The connector

is shown opposite and is labelled H1 on the rear

panel.

Standard Outputs

Electrical HD-SDI

Used On : SHDSDA1S-S1

SHDSDA1E-S1

The high definition serial digital electrical output is

available from eight 75ΩBNC connectors, each

providing identical outputs. These connectors are

shown below and are labelled H2, H3, H4 H5, H6,

H7,H8 and H9.

Note…

The connector at the middle of the backpanel is not

used with this main board but could be used if a

dual channel main board is inserted (see Technical

Profile, OPTIONS).

SHDSDA1 OPERATION

SHDSDA1 Version 1 Issue 3 030402 8

Rollcall Menu System

When a System HD Control and Monitor board is

fitted in the enclosure a range of monitoring

information is available via RollCall

External Monitoring Description

General alarm Input power fault or

overcurrent trip or

system failure

Supply voltage levels Actual voltage levels

Board temperature Actual board

temperature

CRC Status

Line Standard

Frame Rate

Bit error rate Error rate over defined

time period

SHDSDA1 OPERATION

SHDSDA1 Version 1 Issue 3 030402 9

Rollcall Monitoring Features

nModule Infrastructure:

General Alarm

Supply Voltage Levels

Board Temperature

nIncoming Signal analysis:

Input Status

Line Standard

Frame Type

Frame Rate

nCRC Error analysis:

CRC Error Count

CRC Error Total

CRC Reset

nBias/EQ – The value in this field is a guide to

the strength of equalisation that is being

applied to the input signal for longer cable

runs. The lower the value, the less equalisation

is being employed. It is intended as a guide for

troubleshooting the system. It should be noted

that when an equalisation of 100% is shown, it

doesn’t necessarily mean that the maximum

input cable length has been reached. As soon

as CRC errors are being reported then the

input cable length should be decreased until an

error free signal can be received.

SHDSDA1 OPERATION

SHDSDA1 Version 1 Issue 3 030402 10

Manual Revision Record

Date Version No. Issue No. Change Comments

16/06/01 1 1 First draft document Issued

051001 1 2 Edited current feature list Only

states features that are present in

current release A1.0.000

New issue released

030402 1 3 New monitoring features added New issue released

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Amplificador de GRASS VALLEY

GRASS VALLEY

GRASS VALLEY 8941 Manual de usuario

GRASS VALLEY

GRASS VALLEY 8912RDA Manual de usuario

GRASS VALLEY

GRASS VALLEY 8985PRC - Manual de usuario

GRASS VALLEY

GRASS VALLEY 8902 Manual de usuario

GRASS VALLEY

GRASS VALLEY 8945EDA-D - V1.3.0 Manual de usuario

GRASS VALLEY

GRASS VALLEY 8947RDA-FR - Manual de usuario

GRASS VALLEY

GRASS VALLEY 2041EDA Manual de usuario

GRASS VALLEY

GRASS VALLEY 8910ADA-M - Manual de usuario

GRASS VALLEY

GRASS VALLEY 8985PRC - Manual de usuario

GRASS VALLEY

GRASS VALLEY 8947RDA-D - Manual de usuario

GRASS VALLEY

GRASS VALLEY 8943RDA Manual de usuario

GRASS VALLEY

GRASS VALLEY 8945EDA-D - V1.3.0 Manual de usuario

GRASS VALLEY

GRASS VALLEY 8910ADA-M - Manual de usuario

GRASS VALLEY

GRASS VALLEY 2040RDA-FR/16FR Manual de usuario

GRASS VALLEY

GRASS VALLEY 8911 AES-EBU Manual de usuario

GRASS VALLEY

GRASS VALLEY 8943RDA-D Manual de usuario

GRASS VALLEY

GRASS VALLEY 8914 - Manual de usuario

GRASS VALLEY

GRASS VALLEY 8911 AES-EBU Manual de usuario

GRASS VALLEY

GRASS VALLEY 8914 - Manual de usuario

GRASS VALLEY

GRASS VALLEY 7510 Manual de usuario

GRASS VALLEY

GRASS VALLEY 8912RDA-D Manual de usuario

GRASS VALLEY

GRASS VALLEY 8949MDA-SXF Manual de usuario

GRASS VALLEY

GRASS VALLEY 8937 Manual de usuario

GRASS VALLEY

GRASS VALLEY 8916 Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario