GeoVision GV-IPCamera Series Manual de usuario
Quick Start Guide
GV-IPCamera
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Vandal Proof IP Dome
Target Vandal Proof IP Dome
ICH265-A
© 2019 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in
part, without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any
kind and assumes no responsibility for errors or omissions. No liability is
assumed for incidental or consequential damages arising from the use of
the information or products contained herein. Features and specifications
are subject to change without notice. Note: no memory card slot or local
storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
0Uhttp://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the
registered trademark of Microsoft Corporation.
November 2019
i
Contents
Caution.............................................................................. iv
Safety Notice .................................................................... iv
Options .............................................................................. v
Creating GV-IP Camera’s Login Credentials................. vi
Note for Adjusting Focus and Zoom............................. vii
Note for Installing Camera Outdoor............................. viii
Note for Silica Gel Bags ....................................................x
Note for TV-out Function...................................................x
Note for Avoiding IR Reflection.......................................xi
Chapter 1 GV-VD4711 / 5711............................................1
1.1 Packing List ..............................................................................2
1.2 Overview ..................................................................................5
1.3 Installation ................................................................................7
1.3.1 Installation of Weatherproof Shield.............................17
1.4 Connecting the Camera..........................................................18
1.4.1 Power Connection......................................................18
1.4.2 I/O Device Connections .............................................18
1.4.3 Voltage Load Expansion (Optional)............................19
ii
1.5 Loading Factory Default..........................................................20
1.5.1 Using the Web Interface.............................................20
1.5.2 Directly on the Camera ..............................................21
Chapter 2 GV-VD2702 / 2712 / 4702 / 4712....................22
2.1 Packing List ............................................................................24
2.2 Overview ................................................................................26
2.3 Installation ..............................................................................29
2.4 Connecting the Camera..........................................................39
2.5 I/O Connector .........................................................................40
2.5.1 Voltage Load Expansion (Optional)............................40
2.6 Loading Factory Default..........................................................41
2.6.1 Using the Web Interface.............................................41
2.6.2 Directly on the Camera ..............................................41
Chapter 3 GV-EVD2100 / 3100 / 5100 ............................42
3.1 Packing List ............................................................................43
3.2 Overview ................................................................................45
3.3 Installation ..............................................................................47
3.4 Connecting the Camera..........................................................57
3.5 Loading Factory Default..........................................................58
3.5.1 Using the Web Interface.............................................58
3.5.2 Directly on the Camera ..............................................58
iii
Chapter 4 Accessing the Camera..................................59
4.1 System Requirement ..............................................................59
4.2 Accessing the Live View .........................................................59
4.2.1 Checking the Dynamic IP Address .............................60
4.2.2 Configuring the IP Address ........................................61
4.3 Adjusting Image Clarity...........................................................63
4.3.1 Using Focus Adjustment Cap.....................................65
Chapter 5 The Web Interface .........................................66
Chapter 6 Upgrading System Firmware .......................69
iv
Caution
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Safety Notice
The GV-IPCAM uses a Lithium battery as the power supply for its internal
real-time clock (RTC). The battery should not be replaced unless required!
If the battery does need replacing, please observe the following:
Danger of Explosion if battery is incorrectly replaced
Replace only with the same or equivalent battery, as recommended by
the manufacturer
Dispose of used batteries according to the manufacturer's instructions
v
Options
Optional devices can expand your camera’s capabilities and versatility.
Contact your dealer for more information.
Device Description
Power Adapter
The power adapter is available for all Vandal Proof
IP Dome. Contact our sales representatives for the
countries and areas supported.
GV-PA191 PoE
Adapter
The GV-PA191 PoE adapter is designed to provide
power and network connection to the cameras over
a single Ethernet cable.
GV-POE Switch
The GV-POE Switch is designed to provide power
along with network connection for IP devices. The
GV-POE Switch is available in various models with
different numbers and types of ports.
GV-Mount
Accessories
The GV-Mount Accessories provide a
comprehensive lineup of accessories for installation
on ceiling, wall corner and pole. For details, see GV-
Mount Accessories Installation Guide.
GV-Relay V2
The GV-Relay V2 is designed to expand the voltage
load of GV IP devices. It provides 4 relay outputs,
and each can be set as normally open (NO) or
normally closed (NC) independently as per your
requirement.
Metal PG21
Conduit
Connector
The metal PG21 conduit connector is used for
running the wires of GV-VD4711 / 5711, GV-VD2702
/ 2712 / 4702 / 4712, and GV-EVD2100 / 3100 /
5100 through a 3/4” conduit pipe.
Weatherproof
Shield
The weatherproof shield is made for GV-VD4711 /
5711 to protect the camera from rain and snow.
vi
Creating GV-IP Camera’s Login
Credentials
The default Administrator and Guest accounts are no longer supported by
GV-IPCam H.265 series firmware V1.14 or later. When purchasing a new
camera or after resetting it, you need to set up a login username and
password for the camera.
1. Download and install GV-IP Device Utility from our website.
2. On the GV-IP Device Utility window, click to search for your GV-
IP camera.
3. Double-click your GV-IP camera in the GV-IP Device Utility list. This
dialog box appears.
4. Click the Change Username and Password tab to type a new
username and password. Note that the new password must meet
the password strength requirements.
5. Optionally click Upgrade all devices to use the same username
and password on all other devices.
vii
Note for Adjusting Focus and
Zoom
When adjusting the Focus and Zoom Screws, do not over tighten the
Focus and Zoom screws. The screws only need to be as tight as your
finger can do it. It is not necessary to use any tools to get them tighter.
Doing so can damage the structure of lens.
The maximum torque value for all the zoom and focus screws is 0.049 N.m
viii
Note for Installing Camera
Outdoor
When installing the camera outdoor, be sure that:
1. The camera is set up above the junction box to prevent water from
entering the camera along the cables.
2. Any PoE, power, audio and I/O cables are waterproofed using
waterproof silicon rubber or the like.
Este manual sirve para los siguientes modelos
9
Tabla de contenidos
Otros manuales de Cámara de seguridad de GeoVision
GeoVision
GeoVision GV-BX130D-0 Manual de usuario
GeoVision
GeoVision GV-TDR Series Manual de usuario
GeoVision
GeoVision PPTZV10-QG-A Manual de usuario
GeoVision
GeoVision GV-VD8700 Manual de usuario
GeoVision
GeoVision Opal S1 Manual de usuario
GeoVision
GeoVision GV-IP SERIES Manual de usuario
GeoVision
GeoVision GV-BX2700 Series Manual de uso y cuidado
GeoVision
GeoVision GV-EBD4711 Manual de usuario
GeoVision
GeoVision GV-EBX1100 Series Manual de uso y cuidado
GeoVision
GeoVision GV-TMEB5800 Manual de usuario
GeoVision
GeoVision GV-IPCAM Manual de usuario
GeoVision
GeoVision GV-IP Manual de usuario
GeoVision
GeoVision GV-IPCam H.264 Series Manual de usuario
GeoVision
GeoVision GV-BX110D Manual de usuario
GeoVision
GeoVision GV-LPR2811-DL Manual de usuario
GeoVision
GeoVision GV-MFD2401 Manual de usuario
GeoVision
GeoVision GV-GEBF4911 Manual de usuario
GeoVision
GeoVision GV-MFD320 Manual de usuario
GeoVision
GeoVision GV Series Manual de usuario
GeoVision
GeoVision GV-IP LPR-DL Manual de usuario
