Gentex HGU-84/P Instrucciones de instalación

Installation/Operation Instructions

MAXILLOFACIAL SHIELD KIT,

HGU-84/P

05D12001-2 (Medium/Large)

05D12001-3 (X-Large/X-Large Wide)

Ó2006 Gentex Corporation

Contents

OVERVIEW................................1

INSTALLATION .............................2

Tools and Materials Required ...................2

Locating and Marking Snap Holes ................2

Method 1 (Compass) .........................2

Method 2 (Ruler)............................4

Drilling Snap Holes and Installing Snaps .............5

Attaching and Adjusting Maxillofacial Shield ..........6

CLEANING ................................8

CONTACT INFORMATION .......................8

OVERVIEW

The maxillofacial shield kit (Figure 1) includes a maxillofacial shield (MFS) and

attaching hardware designed for installation onto the HGU-84/P helmet. The MFS

protects the lower facial area from flying debris. The MFS is designed to match

the contour of the visors when either visor is deployed.

This booklet contains instructions for installing the MFS. To install the MFS, you

do the following:

•Locate and mark two snap holes on the helmet (using one of two

methods)

•Drill the snap holes and install the snaps

•Attach the MFS to the snaps and adjust the straps as needed.

Figure 1. MFS and Attaching Hardware

MAXILLOFACIAL

SHIELD

ATTACHING HARDWARE

INSTALLATION

Tools and Materials Required

Locating and Marking Snap Holes

To locate the snap holes, you use either Method 1, which requires a compass,

or Method 2, which requires a ruler.

Method 1 (Compass)

1. Remove the visor from the helmet.

2. Set the compass to the value shown below for your helmet size:

Medium: 1-3/8"

Large and X-Large: 1-13/32"

X-Large Wide: 15/16"

3. Referring to Figure 2, position the point of the compass in the top dimple on

one side of the helmet, and draw an arc.

Figure 2. Drawing Arc from Top Dimple

•Compass or ruler

•Scriber

•Screwdriver, cross-tip

•Drill, electrical, portable

•Drill bit, #27

•Drill bit, 1/16

•Maxillofacial shield kit

•Thread-locking adhesive

(Loctiteâ242)

TOP

DIMPLE

ARC

NOTE: This figure shows

the arc location for the

Large and X-Large

helmets. The arc location

for the Medium and

X-Large Wide helmets

will vary from this figure.

Loctiteâis a registered trademark of

Loctite Corporation.

4. Set the compass to the value shown below for your helmet size:

Medium: 1/4"

Large/X-Large: 11/16"

X-Large Wide: 1-1/2"

5. Referring to Figure 3, position the point of the compass in bottom dimple on

the same side of the helmet, and draw an arc.

6. Use a scriber to mark a point where the two arcs intersect.

7. Repeat Steps 2-6 on the other side of the helmet.

Figure 3. Drawing Arc from Bottom Dimple

ARC

BOTTOM

DIMPLE

NOTE: This figure shows

the arc location for the

Large and X-Large

helmets. The arc location

for the Medium and

X-Large Wide helmets will

vary from this figure.

POINT

Method 2 (Ruler)

1. Remove the visor from the helmet.

2. Depending on helmet size, locate and mark the holes on both sides of the

helmet as follows:

NOTE: Figures 4, 5, and 6represent the right side of the helmet as worn.

Medium

a. Referring to Figure 4, draw a line

between the center of the existing

visor snap on the helmet and the

rearward end of the chin strap

grommet.

b. Measure the following distances:

•1-1/8 inch down the line

•5/8 inch to the right of the line

(on the right side of the helmet

as worn)

•5/8 inch to the left of the line

(on the left side of the helmet

as worn)

c. Use a scriber to mark a point at

the end of the 5/8 inch mark. This

will be the location of the snap for

the maxillofacial shield.

Large:

a. Referring to Figure 5, draw a line

2-5/8 inches long upward from,

and perpendicular to, the rearward

end of the chin strap grommet.

b. Use a scriber to mark a point at

the upper end of the line. This will

be the location of the snap for the

maxillofacial shield.

X-Large:

a. Referring to Figure 6, draw a line

between the center of the existing

visor snap on the helmet and the

rearward end of the chin strap

grommet.

b. Measure a point 1-3/8 inch down

the line. Use a scriber to mark the

point. This will be the location of

the snap for the maxillofacial

shield.

(Continued on next page)

Figure 4. Medium/X-Large Wide

Figure 5. Large

Figure 6. X-Large

CHIN STRAP

GROMMET

VISOR

SNAP

POINT

VISOR

SNAP

POINT

CHIN STRAP

GROMMET

CHIN STRAP

GROMMET

POINT

VISOR

SNAP

X-Large Wide:

a. Referring to Figure 4, draw a line between the center of the existing

visor snap on the helmet and the rearward end of the chin strap

grommet.

b. Measure the following distances:

•1-1/16 inch down the line

•3/4 inch to the right of the line (on the right side of the helmet as

worn)

•3/4 inch to the left of the line (on the left side of the helmet as worn)

c. Use a scriber to mark a point at the end of the 3/4 inch mark. This will

be the location of the snap for the maxillofacial shield.

Drilling Snap Holes and Installing Snaps

1. Detach the earcups from the pile fasteners inside the helmet.

WARNING

Wear eye-protective goggles when drilling holes in Steps 2-4 to prevent

eye injury.

CAUTION

•Be careful not to damage any components inside the helmet when

performing Steps 2-4.

•Be sure to drill the helmet shell as specified in Steps 2-4, or delamination

of the helmet shell could result, making the helmet unserviceable.

•When performing Steps 2-4, hold the drill perpendicular to the helmet

shell to prevent damage to the shell and the energy-absorbing liner.

2. Using a drill with a 1/16" drill bit, drill a pilot hole in the marked point.

3. Using a drill with a #27

drill bit, drill a finishing

hole in the pilot hole.

4. Repeat Steps 2 and 3 on

the other side of the

helmet.

5. Referring to Figure 7,

install a snap with a

screw, a lock washer,

and a nut on each side

of the helmet in the

drilled holes. Before

installing the screws,

apply thread-locking

adhesive to the threads

of each screw.

Figure 7. Installing Snap

NUT*

LOCK

WASHER*

DRILLED

HOLE

SNAP SCREW

* INSIDE HELMET

Attaching and Adjusting Maxillofacial Shield

1. Reattach the earcups to the pile fasteners inside the helmet.

2. Reattach the visor to the helmet.

3. Referring to Figure 8, attach the maxillofacial shield to the helmet by

fastening its snap to the newly installed snap from front to back. Repeat for

the other side.

4. Adjust the maxillofacial shield straps as needed.

5. Adjust the helmet microphone so that it fits inside the maxillofacial shield.

Figure 8. Attaching Maxillofacial Shield

6. Referring to Figure 9, lower the visor to check the interface between the

visors and the maxillofacial shield. If necessary, readjust the visor straps

and/or the maxillofacial shield straps.

7. To remove the maxillofacial shield, pull the shield strap away from the

helmet.

Figure 9. Visor Lowered to Check Interface with Maxillofacial Shield

CLEANING

Wipe the maxillofacial shield with a clean cloth dampened with a mild

soap-and-water solution.

CONTACT INFORMATION

Maxillofacial Shield Kit

Part Number 05D12001-2 (Medium/Large)

05D12001-3 (X-Large/X-Large Wide)

For more information about the maxillofacial shield kit, contact:

Gentex Corporation

P.O. Box 315

Carbondale, PA 18407

Phone: (570)282-3550

Fax: (570)282-8555

www.gentexcorp.com.

Otros manuales para HGU-84/P

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios para motocicletas de Gentex

Gentex

Gentex TBH IIIA Series Manual de usuario

Gentex

Gentex HGU-84/P Guía de solución de problemas

Gentex

Gentex HGU-56/P Guía de solución de problemas

Gentex

Gentex Active Shooter Manual de usuario

Gentex

Gentex SPH-5 Manual

Gentex

Gentex HGU-56/P Manual de instrucciones

Gentex

Gentex SPH-4B Manual de usuario

Gentex

Gentex HGU-55/P Guía de configuración

Gentex

Gentex HELMET Purelite Xstream NEU Manual de usuario

Gentex

Gentex SPH-5 Manual de usuario

Gentex

Gentex CVC M9 Manual de usuario

Manuales populares de Accesorios para motocicletas de otras marcas

SRC

SRC B-TRK502-01-01-SL Manual de usuario

3M Speedglas 9100 MP Manual de usuario

hepco & becker

hepco & becker 6307520 00 01 Manual de usuario

HOMCOM

HOMCOM AA0-077 Manual de usuario

hepco & becker

hepco & becker 6307558 00 01 Manual de usuario

Wunderkind Custom

Wunderkind Custom 106503-F15 Guía del usuario

Dräger

Dräger HPS 3500 Manual de usuario

M-WAVE

M-WAVE SKI Manual de usuario

Kuryakyn

Kuryakyn 6212 Manual de usuario

hepco & becker

hepco & becker 6507504 00 01 Manual de usuario

Tool it

Tool it PROMAX LCD 9.13G Manual de usuario

Custom Dynamics

Custom Dynamics TruWrapz Manual de usuario

Roof

Roof RO200 CARBON Manual de usuario

Kabuto

Kabuto Japan IBUKI Manual de usuario

PUIG

PUIG 5051 Manual de usuario

rizoma

rizoma ZTH050 Manual de usuario

Joubert

Joubert 10001711 Manual de usuario

Sperian

Sperian Optrel p420 Manual de usuario