Gefen EXT-HDMI1.3-244 Manual de usuario
www.gefen.com
f
2X4 Switcher for
1.3
EXT-HDMI1.3-244
User Manual
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday thru Friday.
Write To:
Gefen Inc.
c/o Customer Service
20600 Nordhoff St
Chatsworth, CA 91311
www.gefen.com
Notice
Gefen Inc. reserves the right to make changes in the hardware, packaging and
any accompanying documentation without prior written notice.
2x4 Switcher for HDMI 1.3 is a trademark of Gefen Inc.
© 2008 Gefen Inc., All Rights Reserved
All trademarks are the property of their respective companies
ASKING FOR ASSISTANCE
Rev XA
CONTENTS
1 Introduction
2 Operation Notes
3 Features
4 Panel Layout
5 Panel Descriptions
6 Connecting And Operating The 2X4 Switcher For HDMI 1.3
7 RMT2-IR Remote Control Description
8 IR Channel Configuration
10 Specifications
11 Warranty
1
Congratulations on your purchase of the 2x4 Switcher for HDMI 1.3. Your
complete satisfaction is very important to us.
Gefen
Gefen delivers innovative, progressive computer and electronics add-on solutions
that harness integration, extension, distribution and conversion technologies.
Gefen’s reliable, plug-and-play products supplement cross-platform computer
systems, professional audio/video environments and HDTV systems of all sizes
with hard-working solutions that are easy to implement and simple to operate.
The Gefen 2x4 Switcher for HDMI 1.3
Gefen’s 2x4 Switcher for HDMI 1.3 is equipped with two HDMI™ inputs and
four HDMI outputs. Two inputs accommodate the simultaneous connection of
up to two high definition video sources, such as satellite systems and HD DVD
players. Four outputs send the high definition audio/video signals to up to four
high definition displays. Switching is done via the IR remote that is provided with
the unit.
How It Works
You simply connect all your sources to the Switcher’s inputs. Then connect up
to four displays on the output ports. Once the sources, the Switcher and the
display(s) are powered and connected, you simply select which source you want
to view using the IR remote.
Note:
All displays that cannot show the same video resolution(s) as the Primary Display
connected to Output #1 may fail to show a picture. Secondary displays follow the
Primary by sharing the resolution and capability information (EDID) obtained from
the Primary Display.
INTRODUCTION
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE 2X4 SWITCHER FOR HDMI 1.3
• Display information (EDID) is needed by the source to determine the
capabilities of the connected display. This is especially important for HDMI
1.3 sources because without the right information in the EDID none of
the features for HDMI1.3 will be enabled. The 2x4 Switcher for HDMI 1.3
features an EDID selection that will allow the user to choose an external
EDID from an attached display or an built-in internal EDID. Please see page
6 for more details.
• The source device will output a single video resolution that all displays must
be capable of accepting.
• This devices is HDMI 1.3 compliant. Please see page 3 for supported HDMI
1.3 features.
• Supports HDTV resolutions up to 1080p Full HD and computer resolutions of
1900 x 1200.
2
OPERATION NOTES
3
Features
• Switch easily between any two HDMI™/DVI sources
• Outputs are mirrored to four HDMI™/DVI displays simultaneously
• Maintains high resolution video - beautiful, sharp HDTV resolutions up to
1080p, 2k, and computer resolutions up to 1920 x 1200 are easily achieved
• Discrete IR remote (included)
• HDMI™ and HDCP compliant
HDMI 1.3 Features
• Lip-Sync Pass Through
• 225 MHz (up to 12 bit YUV 444 supported @ 1080p)
• Deep Color Supported (XV Color Supported)
• Color Space Conversion Supported
• Dolby TrueHD & DTS Master Supported
• CEC Pass Through
Package Includes
(1) 2x4 Switcher for HDMI 1.3
(1) RMT-2IR Remote Control
(2) 6-Foot HDMI cables
(1) 5V DC Power Supply
(1) User’s Manual
FEATURES
4
Front Panel
Back Panel
1 2 3 4 5 6
7 8 119 10
PANEL LAYOUT
5
1 Power LED Indicator
This LED will become active once the included 5V DC power supply is properly
connected between the unit and a open wall power receptacle.
2 IR (Infrared) Receiver
This receiver will accept command for switching between input HDMI devices
using the included RMT-2IR remote control.
3 Internal EDID Mode LED Indicator
This LED will become active when the unit is using the pre-loaded EDID. Please
see page 6 for more details.
4 External EDID Mode LED Indicator
This LED will become active when the unit is using the EDID from the HDMI
deice connected to HDMI output port 1. Please see page 6 for more details.
5 Link LED Indicator
This LED will become active when the unit is properly connected to an HDMI
capable device on either of the HDMI output ports.
6 Currently Selected Input LED Indicator
There is one LED for each of the four input ports. The LED for the currently
selected HDMI input will be active.
7 EDID Selection Toggle Button
This button will toggle between the internal external EDID modes. To determine
which mode is currently being used, please note which EDID mode LED is
active on the front panel of the unit.
8 Reset Button
This button will reset the unit and force all devices in the chain to re-transmit/
re-read EDID. It is essential that the unit be reset after the EDID mode has been
changed. Please see page 6 for more details.
9 HDMI Input Ports 1-2
Connect up to 2 HDMI source devices to these HDMI input ports. Selection
between these inputs are made using the included RMT-2IR remote control.
10 HDMI Output Ports 1-4
Connect up to 4 HDMI capable devices to these HDMI output ports. The
currently selected HDMI input source device will be output through all of these
HDMI output ports.
11 5V DC Power Input Port
Connect the included 5V DC power supply between this port and an open wall
power receptacle.
PANEL DESCRIPTIONS
6
How to Connect the 2x4 Switcher for HDMI 1.3
1. Connect up to two HDMI source devices to the 2x4 Switcher for HDMI 1.3
using the supplied HDMI cables.
2. Connect up to four HDMI capable devices to the 2x4 Switcher for HDMI 1.3
using the supplied HDMI cables.
NOTE: The display connected to the port labeled OUT 1 will have its EDID
used when the external EDID mode is active. If there are displays with different
resolutions in the setup it is recommended that the display with the lowest
resolution be placed on the HDMI port labeled OUT 1. This way, all of the
displays should be able to display an image when the external EDID mode is
active.
3. Connect the included 5V DC power adapter to the 2x4 Switcher for HDMI
1.3 power input port.
4. Power on the displays first and then the source.
How to Operate the 2x4 Switcher for HDMI 1.3
Use the included RMT2-IR remote control to switch between HDMI inputs.
Please see page 7 for a description of the RMT2-IR remote control.
EDID Modes and Reset Buttons
The EDID source is selectable between the display connected to the HDMI
output port labeled OUT 1 or the built-in internal EDID. These 2 modes are
selectable by toggling the EDID button located on the back panel. To switch
modes, follow the instructions below.
1. Note the current EDID mode by viewing the front panel’s LED array. If the
INT LED is active the internal EDID mode is in use. If the EXT LED is active
the external EDID mode is in use.
2. If the currently selected EDID mode is not the desired EDID mode, press the
EDID button on the rear panel once. The active LED will now switch and the
new EDID mode will become active once the unit is reset.
3. Press the reset button to cycle power and initiate the newly selected EDID
mode.
The EDID carries import information that the source reads to determine what
resolutions and features are supported. The internal EDID has support for
resolutions up to 1080p and includes Dolby TrueHD and DTS-HD features.
CONNECTING AND OPERATING THE 2X4 SWITCHER FOR HDMI 1.3
7
The included RMT-2IR remote control is used to switch between inputs on the 2x4
Switcher for HDMI 1.3. Only one input can be selected at a time and this input is then
mirrored to the four HDMI outputs on the rear panel.
Switching
Press the 1 button to switch to HDMI input 1.
Press the 2 button to switch to HDMI input 2.
RMT2-IR REMOTE CONTROL DESCRIPTION
Otros manuales para EXT-HDMI1.3-244
2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de Gefen
Gefen
Gefen HDMI-441 Manual de usuario
Gefen
Gefen 2x4 HDMI Switcher/Splitter Manual de usuario
Gefen
Gefen 4x1 DVIKVM Switcher series Manual de usuario
Gefen
Gefen EXT-3GSDI-441 Manual de usuario
Gefen
Gefen ex-tend-it 4x4 HDTV Matrix Manual de usuario
Gefen
Gefen 4K ULTRAHD EXT-UHD-88 Manual de usuario
Gefen
Gefen DVI-422 Manual de usuario
Gefen
Gefen 4K Ultra HD HDBaseT EXT-4K300A-MF-41-HBTLS Manual de usuario
Gefen
Gefen 4x4 HDMI Manual de usuario
Gefen
Gefen EXT-DIGAUD-241 Manual de usuario
Gefen
Gefen EXT-DVIK-MV-41 Manual de usuario
Gefen
Gefen GTVGTV-HDMI1 Manual de usuario
Gefen
Gefen VGA Manual de usuario
Gefen
Gefen RMT-MATRIX-444 Manual de usuario
Gefen
Gefen EXT-DVIK-MV-441 Manual de usuario
Gefen
Gefen DVI-441N Manual de usuario
Gefen
Gefen EXT-DVI-422DL Manual de usuario
Gefen
Gefen EXT-3GSDI-441 Manual de usuario
Gefen
Gefen EXT-UHDV-WP-HBTLS-TX Manual de usuario
Gefen
Gefen EXT-MINIDVI-241N Manual de usuario
