Gefen EXT-DVI-CAT5-4X Manual de usuario
DVI CAT5 4X
Extender
USER MANUAL
www.gefen.com
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday thru Friday.
Write To:
Gefen Inc.
c/o Customer Service
20600 Nordhoff St
Chatsworth, CA 91311
www.gefen.com
Notice
Gefen Inc. reserves the right to make changes in the hardware, packaging and
any accompanying documentation without prior written notice.
The EXT-DVI-CAT5-4X is a trademark of Gefen Inc.
© 2007 Gefen Inc., All Rights Reserved
ASKING FOR ASSISTANCE
TABLE OF CONTENTS
INTRODUCTION
FEATURES
EXT-DVI-CAT5-4X PANEL DESCRIPTIONS
EXT-DVI-CAT5MSR RECEIVER PANEL DESCRIPTIONS
HOW TO CONNECT AND USE THE EXT-DVI-CAT5-4X
DIP SWITCH USAGE GUIDE
DIP SWITCH DIAGRAM
CAT5 LINK CABLE - WIRING DIAGRAM
EXT-DVI-CAT5-4X RACK MOUNT INSTALLATION
EXT-DVI-CAT5MSR MOUNTING PLATE INSTALLATION
FREQUENTLY ASKED QUESTIONS
TERMINOLOGY
SPECIFICATIONS
WARRANTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
OPERATION NOTES
INTRODUCTION
Thank you for purchasing the DVI CAT5 4X Extender.
The DVI CAT5 4X Extender can extend 4 single link (1920 x 1200) DVI sources
to 4 displays up to 300ft away.
The 4x4 DVI CAT5 Distribution Amplier is the perfect solution for anyone who
needs to send multiple sources to multiple displays in remote locations at the
same time.
The DVI CAT5 4X Extender has 4 DVI single link inputs with 8 (2 per display)
RJ45 output ports. Each pair of CAT5e cables will extend out to a single receiver
with 2 RJ45 inputs and one DVI output port for your display. This will allow you
to extend 4 separate video signals to 4 remote locations.
1
READ THESE NOTES BEFORE INSTALLING
OR OPERATING THE DVI CAT5 4X Extender
• The DVI CAT5 4X Extender and DVI CAT5 MSR units are housed in a metal
box for better RF shielding.
• Your CAT5e cables should not exceed 300 feet.
• If you do not need DDC or HDCP data you can use a single CAT5e cable for
the video only. The DDC will not be connected. (For further information, see
our Terminology section on page 9.) If HDCP is required, both CAT5e cables
must be used between the sender and receiver units.
• If you are using a single CAT5e cable and the source requires EDID present,
you can use the Gefen DVI Detective to provide EDID information to your
source. The DVI Detective will not transmit HDCP.
• Shielded CAT5e or CAT6 with metal RJ-45 connectors is recommended to
protect from random video ashes caused by EMI.
• Power supply for the receiver should not be connected unless you are using
one CAT5e or going over a distance of 180ft.
• Extensions over 130ft. require you to manually EQ your signal (see page 5).
• Extensions under 130ft. use Auto EQ (which is on by default) (see page 5).
NOTE: The DVI CAT5 4X Extender is fully HDCP compliant
2
Features:
• Allows 4 DVI single link sources to be extended up to 300ft.
• Maintains resolutions up to 1080p, 2K, and 1920x1200
• Maintains highest DVI single link video resolution
• DVI or HDMI to DVI cables are used to connect the inputs and outputs of the
matrix
INCLUDES:
(1) EXT-DVI-CAT5-4X
(4) EXT-DVI-CAT5MSR
(4) 6 ft DVI to DVI Cable M-M
(1) 24V DC power supply
(4) 5V DC power supply
(1) Rack Ears
FEATURES
EXT-DVI-CAT5-4X SENDER PANEL DESCRIPTIONS
FRONT
BACK
3
Video 4
RJ45 Outputs
Video 4
DVI Input
Power LED
Video 3
DVI Input
Video 2
DVI Input
Video 1
DVI Input
24V DC Power Input
Video 3
RJ45 Outputs
Video 2
RJ45 Outputs
Video 1
RJ45 Outputs
EXT-DVI-CAT5MSR RECEIVER PANEL DESCRIPTIONS
4
Connects to DVI display
CAT-5 carries
TMDS signals
CAT-5 carries
DDC/HDCP signals
Connects to 5 volt
power supply
Power Indicator
EQ trim pod
Connect your source(s) to the EXT-DVI-CAT5-4X sender unit's DVI
input(s).
Connect your display(s) to the EXT-DVI-CAT5MSR receiver unit's DVI
output(s).
Connect both CAT5e cables (DDC and Video) between the sender and
the receiver
Plug the 24V power supply into the EXT-DVI-CAT5-4X sender.
If you are not receiving a video signal, follw the steps below to manually
equalize the signal.
HOW TO CONNECT THE EXT-DVI-CAT5-4X
1
2
3
4
5
HOW TO USE THE EQ TRIM POT
The EQ trim pot is used extensions over 130 ft. By default, the DVI CAT5
MSR receivers come set to "Auto EQ" (with dip switch 1 ON). Underneath
the receiver is a bank of dip switches hidden by a blank sticker. If you ip dip
switch 1 OFF you can turn off the "Auto EQ" so that you can manually EQ your
signal by using the EQ trim pot on the receiver. If you ip dip switch number
1 to the ON position you can set the DVI CAT5 MSR to "Auto EQ". Auto EQ
works only when the sender is set to "NO BOOST" (see page 6). Auto EQ
works reliably up to 130ft. If you are using the DVI CAT5 MSR beyond any
distance of 130 ft. you will have to manually EQ your signal.
USING THE TRIMPOT
Have both of your CAT5e or CAT6 cables connected.
Start by having the source connected and playing with your display on.
Start with the trimpot turned all the way counter clockwise and slowly turn
the trim pot clockwise until the image stablilizes and displays no noise.
1
2
3
If you still do not get a picture or have video noise, set the sender's to medium
boost and try to re-EQ your signal. If that still does not work try the high boost
setting.
DIP SWITCH GUIDE
6
The EXT-DVI-CAT5-4X and EXT-DVI-CAT5MSR products both contain a set
of service switches (also called dip switches) located underneath each unit.
The EXT-DVI-CAT5-4X has 4 sets of DIP switches, one for each input, while
the EXT-DVI-CAT5MSR has a single bank of DIP switches. Peeling back the
silver sticker on the bottom of either unit will reveal the DIP switch bank. These
service switches are used to boost and equalize the signal to best match the
conditions in your setup. (*Note: Adjustments should be done with sources
and display on. Switches 3 and 4 are not used.)
Sender Dip Switch Settings
Setting Switch 1 Switch 2
No Boost OFF ON
Normal Boost (Default) OFF OFF
Strong Boost ON OFF
Undened ON ON
Receiver Dip Switch Settings
Setting Switch 1 Switch 2
No EQ (Default) OFF OFF
EQ Setting 2 ON OFF
EQ Setting 3 OFF ON
Maximum EQ ON ON
Adjustment Guidelines:
1) Strong boost should not be used on stranded cables. Strong boosting
will cause pixels or no picture on these cables.
2) Using the wrong settings will not damage the units; it will either
produce no image or a noisy image.
3) To eliminate the possibility of cross talk and interference, cables must
be terminated with 568B scheduling. (See page 7 for details)
DIP SWITCH DIAGRAM
7
Remove Ta pe
Equalization
Trim Pot
Auto EQ Dip Switches
1432
1432
Boost Dip Switches
Remove Tape
FRONT
EXT-DVI-CAT5MSR
EXT-DVI-CAT5-4X
Otros manuales para EXT-DVI-CAT5-4X
2
Tabla de contenidos
Otros manuales de Extensor de Gefen
Gefen
Gefen Toolbox GTB-HDMI-3DTV Manual de usuario
Gefen
Gefen ETH-2-PLC Manual de usuario
Gefen
Gefen HDMI-141SB Manual de usuario
Gefen
Gefen CAT5-5500HD Manual de usuario
Gefen
Gefen EXT-DVIRS232-1FO Manual de usuario
Gefen
Gefen DVI-1000HD Manual de usuario
Gefen
Gefen USB-400 Manual de usuario
Gefen
Gefen EXT-DVI-1CAT5-SR Manual de usuario
Gefen
Gefen EXT-HDMI1.3-1FO Manual de usuario
Gefen
Gefen DVI-141DLB Manual de usuario
Gefen
Gefen HDMI CAT-5 Manual de usuario
Gefen
Gefen GTB-UHD2IRS-ELRPOL-BLK Manual de usuario
Gefen
Gefen COMP-141N Manual de usuario
Gefen
Gefen GTV-WVGA-LR Manual de usuario
Gefen
Gefen HDMI-141SBP Manual de usuario
Gefen
Gefen DVI-141SBP Manual de usuario
Gefen
Gefen EXT-CAT5-1600A Manual de usuario
Gefen
Gefen ToolBox GTB-USB2.0-4LR Manual de usuario
Gefen
Gefen RS-232 Manual de usuario
Gefen
Gefen EXT-PS2-100 Manual de usuario
