Gefen EXT-DVI Audio-Cat5 Manual de usuario
www.gefen.com
®
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday thru Friday PST
Write To:
Gefen LLC
c/o Customer Service
20600 Nordhoff St.
Chatsworth, CA 91311
www.gefen.com
Notice
Gefen LLC reserves the right to make changes in the hardware, packaging and any
accompanying documentation without prior written notice.
The DVI Audio Extender is a trademark of Gefen LLC
All trademarks are the property of their respective owners.
© 2011 Gefen LLC, All Rights Reserved
ASKING FOR ASSISTANCE
Rev A1
TABLE OF CONTENTS
1. Introduction
2. DVI Audio Extender Sender Panel Descriptions
3. DVI Audio Extender Receiver Panel Descriptions
4. How To Connect The DVI Audio Extender
5. Service Switch Usage Guide
6. CAT5 Link Cable - Wiring Diagram
7. Frequently Asked Questions
8. Terminology
9. Specifications
10. Warranty
READ THESE NOTES BEFORE INSTALLING
OR OPERATING THE DVI AUDIO EXTENDER
• The DVIAudio Extender is housed in a metal box for better RF shielding.
• Your CAT-5 cable should not exceed 300 feet for 1280x1024/1080i.
• Your CAT-5 cable should not exceed 150 feet for 1920x1080/1080p.
• If the source requires EDID present, you can use the Gefen DVI Detective to
provide EDID information
• CAT6 cable is suitable for high resolutions at 50 meters.
OPERATION NOTES
INTRODUCTION
The DVIAudio Extender sender unit sits next to your computer, DVD player or any set-
top box with a DVI output. The cable supplied with the DVI Audio Extender connects
your DVI source to the send unit. The DVIAudio Extender receiver unit sits next to your
DVI display - up to 200 feet at 1280x1024/1080i ( 150 feet at 1920x1200/1080p). The
display plugs into the back of the DVIAudio Extender receiver unit. Two CAT-5 cables
connect the DVI Audio Extender-S and the DVI Audio Extender-R units to each other
Package Includes
(1) DVI Audio Extender-S
(1) DVI Audio Extender-R
(1) 6 ft DVI to DVI Cable M-M
(2) 5V DC power supply
(1) 6 ft Audio RCA Cable
1
DVI AUDIO EXTENDER SENDER PANEL DESCRIPTION
2
DVI input connects to
DVI source
Connects to 5 volt
power supply
Optical Audio In
SPDIF Audio In Analog Audio In
DDC/Audio Video
DVI AUDIO EXTENDER RECEIVER PANEL DESCRIPTIONS
3
Analog Audio Out DVI Output connects to
DVI Display
Optical Audio Out
SPDIF Audio Out
DDC/Audio
Video
Connects to 5 volt
power supply
1. Connect your source to the DVI Audio Extender sender unit using the included
DVI Cable.
2. Connect the audio from your source to the DVI Audio Extender sender using the
included analog RCA cables or optional digital audio cable.
3. Connect your display to the DVI Audio Extender receiver unit using a DVI Cable.
4. Connect the audio on your display or audio receiver to the DVI Audio Extender
receiver unit using the analog RCA cables or optional digital audio cable.
5. Connect your CAT-5 cables between the sender and the receiver
6. Plug the 5V power supply into the DVI Audio Extender sender and receiver unit
7. You should now have picture and sound. If you do not see a picture, try
unplugging and re-plugging the DVI input on the DVI sender unit. Make sure
your CAT-5 cables are not crossed. Recycle the power on the unit.
* If problems persist try adjusting the Dip Switches by following the Dip Switch
Usage Guide.
HOW TO CONNECT THE DVI AUDIO EXTENDER
4
5
SERVICE SWITCH USAGE GUIDE
The Sender and Receiver of the Gefen DVI Audio Extender both contain a set of
service switches (also called dip switches) located underneath each unit. Peeling
back the silver sticker will reveal the service switch bay. These service switches are
used to boost and equalize the signal to best match the conditions in your setup.
(*Note: Adjustments should be done with sources and display on. Switches 3 and 4
are not used.)
Sender Dip Switch Settings
Setting Switch 1 Switch 2
No Boost OFF ON
Normal Boost (Default) OFF OFF
Strong Boost ON OFF
Undefined ON ON
Receiver Dip Switch Settings
Setting Switch 1 Switch 2
No EQ (Default) OFF OFF
EQ Setting 2 ON OFF
EQ Setting 3 OFF ON
Maximum EQ ON ON
Adjustment Guidelines:
1) Strong boost should not be used on stranded cables. Strong boosting will
cause pixels or no picture on these cables.
2) Using the wrong settings will not damage the units; it will either produce no
image or a noisy image.
3) To eliminate the possibility of cross talk and interference, cables must be
terminated with 568B scheduling. (See page 6 for details)
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Extensor de Gefen
Gefen
Gefen EXT-USB-MIDI Manual de usuario
Gefen
Gefen ToolBox GBT-HDBT-POL Manual de usuario
Gefen
Gefen EXT-DVI-1500HD Manual de usuario
Gefen
Gefen HDTV-CAT5 Manual de usuario
Gefen
Gefen CAT5-9000I Manual de usuario
Gefen
Gefen ToolBox GTB-DPKVM-3CAT7 Manual de usuario
Gefen
Gefen DVI-141SB Manual de usuario
Gefen
Gefen EXT-DVI-141SBP Manual de usuario
Gefen
Gefen CAT5-5000HD Manual de usuario
Gefen
Gefen EXT-WHD-1080P-SR Manual de usuario
Gefen
Gefen HDMIRS232-CAT5 Manual de usuario
Gefen
Gefen ULTRA HD EXT-HDBOOST-141 Manual de usuario
Gefen
Gefen USB-400 Manual de usuario
Gefen
Gefen ex-tend-it DVI Detective Manual de usuario
Gefen
Gefen RS-232 Manual de usuario
Gefen
Gefen VDL-1000 Manual de usuario
Gefen
Gefen EXT-DVI-1CAT6 Manual de usuario
Gefen
Gefen EXT-DVI-EDIDP Manual de usuario
Gefen
Gefen DVI-141B Manual de usuario
Gefen
Gefen EXT-HDMI1.3-1CAT6 Manual de usuario
