GE RM94940 Manual de usuario
Universal
Remote Control
RM94940
INSTRUCTION
MANUAL
94940 Revised Size 10/18/02 12:22 PM Page 1
1
Thank you for purchasing the GE Universal Remote
Control. This product is designed to provide years of
service operating a wide variety of video and audio
equipment.
Please retain this guide for future reference.
Table of Contents
Install the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Button Description . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Learning Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Clearing a Learned Function . . . . . . . . . . . . . . . . . . . . .5
Clearing All Learned Buttons . . . . . . . . . . . . . . . . . . . .5
Programming for TV . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Programming for VCR . . . . . . . . . . . . . . . . . . . . . . . . . .7
Programming For DVD . . . . . . . . . . . . . . . . . . . . . . . . .8
Programming For DBS System . . . . . . . . . . . . . . . . . . .9
Programming For Cable . . . . . . . . . . . . . . . . . . . . . . .10
Programming For CD . . . . . . . . . . . . . . . . . . . . . . . . .11
Programming For AUX 1 or AUX 2 . . . . . . . . . . . . . .12
Sleep Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Programming With Code Search . . . . . . . . . . . . . . . .14
Identifying Codes For Your Remote . . . . . . . . . . . . . .14
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . .15-16
Device Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36-39
This Universal Remote Control is already programmed
for most GE, RCA and ProScan TVs, VCRs, DBS
Systems, DVD Players, and Audio/Video Receivers.
NOTE: For users of GE, RCA and ProScan DBS
Products, older DBS models require that the DISPLAY
Button on this remote be used to make program selec-
tions. Use the SELECT Button for making program
selections on newer GE, RCAand ProScan DBS models.
Battery Installation
Your Universal Remote Control requires 2 AAA alka-
line batteries.
To install the batteries:
1. Turn the remote over and push down on the cover
and slide it off.
2. Insert the batteries, matching the batteries to the (+)
mark inside the battery case.
3. Slide the battery cover back into place.
NOTE: Programmed codes will remain in memory for
a short period of time allowing for battery replacement.
If batteries have been dead for a prolonged period of
time, reprogramming may be required.
94940 Revised Size 10/18/02 12:22 PM Page 2
2
Button Description
INDICATOR LIGHT
The Indicator Light flashes to show that the remote is
working.
ON•OFF
The ON•OFF button operates the same as your origi-
nal remote.
NOTE: Some GE, RCA and ProScan models require
you to press the device button to turn the device on
and the ON•OFF button to turn the device off.
LEARN
The Learn button allows you to “record” and “delete”
“learned” functions from the original or other remote
controls.
TV, VCR, DVD, CD, AUX 1, AUX 2, CBL/SAT
These buttons are used to select the device you want to
control.
VOL & CHAN
The VOL (Volume) and CHAN (Channel) buttons
increase or decrease the channel numbers or
volume.The CHANNEL buttons also control the SKIP
functions for DVD and CD Player.
MUTE
Mutes volume on the TV.
PREV CH
The PREV CH button allows you to go to the previous
channel you selected. Operates the same as Last
Channel, Go Back or Recall on your original remote.
CODE SEARCH
Used to program the remote or to search through
codes.
GUIDE
Brings up the on-screen TV program guide if your TV
has that feature.
DISP
Display Button shows the date and the time if your TV
or VCR has that feature.
NAVIGATION BUTTONS & SELECT
Used to move through on-screen menuing and guides.
With some DBS models the DISP button should be
used to select the highlighted item. Use the navigation
buttons to move the highlighted choice up, down, left
or right.
L1, L2, L3
The L1-L3 buttons are used for storing learned func-
tions from the original or other remote controls.
94940 Revised Size 10/18/02 12:22 PM Page 3
3
MENU
Brings up the Main Menu. If you already in the menu
system, press SELECT to select a highlighted choice.
Use the arrows buttons to move through the Menu
Selection.
CLEAR
Removes the on screen display to return to normal
viewing.
0-9
The number buttons operates the same as on your orig-
inal remote, and are used for entering device codes.
ENTER
The ENTER button is used to complete channel selec-
tion for some brands of TV. It is also used to complete
the code search process.
TV/VCR
The TV/VCR button operates the TV/VCR function of
your TV.
REW, PLAY, FF, REC, STOP, PAUSE
These buttons operate the same as on your original
VCR or remote.You must press the REC button twice to
begin recording. The REW and FF buttons also control
the Reverse and Forward functions for DVD and CD
Player.
SLEEP
The SLEEP button allows you to set a time for you to
turn off your TV automatically.
94940 Revised Size 10/18/02 12:22 PM Page 4
4
Learning Function
The learning feature is used as a supplement to the standard prepro-
grammed library. The standard code library provides most of the
functions needed, but you can add a small number of additional
functions of your choice.
Note: No functions may be stored under the LEARN, SLEEP, CODE
SEARCH, MENU or any of the device buttons.
1. Place the 94940 remote control unit
and the Original remote control unit
so that they face each other. They
should not be any more than 2 inches
apart.
2. Press and hold the CODE SEARCH
button until the INDICATOR LIGHT
lights, then release the CODESEARCH
button.
3. Press and release the desired Mode
button (TV, VCR, CABLE, SAT, etc. . . .)
The INDICATOR LIGHT will blink off
once button press is accepted.
4. Press and release the LEARN button.
5. Press and release the valid button to
be learned on the 94940 remote in which
you will store a new function. The L1,
L2, L3 or other functions keys may be used
in this programming mode.
6. Press and hold the button on the original
remote control until INDICATORLIGHT
on the 94940 remote blinks once. Once the
INDICATORLIGHT blinks you may con-
tinue with the next function.
If there is error in learning the new func-
tion the INDICATOR LIGHT will flash for
3 seconds but remain in the learning mode.
Return to step 5 if the INDICATORLIGHT
flashed.
NOTE: Hold the function key on your origi-
nal remote for at least 3 seconds for the com-
mand to be successfully learned.
7. Repeat steps 5 and 6 to store more func-
tions.
8. Once the selected functions are stored
press the CODESEARCH button and the
remote will return to original operation
mode.
2 inches
CD CBL/SAT
BLINK
LEARN
L1 L2 L3
94940 Revised Size 10/18/02 12:22 PM Page 5
Clearing A Learned Button
To clear a learned button sequence, use
the procedure below.
Note: No functions may be stored under
the LEARN, SLEEP, CODE SEARCH or
any of the device buttons.
1. Press and hold the CODE SEARCH
button until the INDICATORLIGHT
lights, then release the CODESEARCH
button.
2. Press an release the desired Mode but-
ton (TV, VCR, CABLE,SAT, etc. . . ).
The INDICATOR LIGHTwill blink off
once the button press is accepted.
3. Press and release the LEARN button twice.
The INDICATOR LIGHT will light off once the
button press is accepted.
4. Press and release the CODESEARCH button
and the remote will return to original operation
mode. All learned command functions under the
device are now cleared.
Clearing All Learned Buttons
This procedure will erase all learned functions in every device mode.
This step is recommended when attempting any learning of a new
function from a new remote.
1. Press and hold the CODE SEARCH
button until the INDICATOR LIGHT
lights, then release the CODESEARCH
button.
2. Press and release the LEARN button
twice. The INDICATOR LIGHT will
light off once the button press is accept-
ed.
3. Press and release the CODE SEARCH
button and the remote will return to
original operation mode. All learned
command entries are now cleared.
5
CD CBL/SAT
LEARN
LEARN
AUX
94940 Revised Size 10/18/02 12:22 PM Page 6
6
Programming For TV
Most GE, RCAand ProScan TVs will not require pro-
gramming. Check to see if your TV responds to the
remote before you begin programming.
1. Manually turn on the TV. Find the three digit code
for your TV in the code list at the back of the instruc-
tions.
2. Press and hold the
CODESEARCH button
until the INDICATOR
LIGHT lights, then
release the CODE SEARCH
button.
3. Press and release the TV
button (The INDICATOR
LIGHT will blink then
remain lit.
4. Enter the code using the
Number Buttons. After your
code is entered, the INDI-
CATOR LIGHT will turn
off. If the code is not valid,
the INDICATOR LIGHT
will blink. Check the code
list and repeat process.
5. Aim the remote at your
TV and press the ON•OFF
button. Your TV should turn
off.
NOTE: If your TV does not
respond, try all the codes for
your brand. If the codes do
not work, or your brand is
not listed, try the Code
Search method on Page 12.
6. With your TV on, press CHAN+ (CHANNELUP).
If the TV responds, no further programming is
required.
7. Enter your code here for
easy reference.
TV CODE LIST
94940 Revised Size 10/18/02 12:22 PM Page 7
7
Programming For VCR
Most GE, RCAand ProScan VCRs will not require
programming. Check to see if your VCR responds to
the remote before you begin programming.
1. Manually turn on the VCR. Find the three digit
code for your VCR at the back of the instructions.
2. Press and hold the
CODESEARCH button
until the INDICATOR
LIGHT lights, then
release the CODE
SEARCH button.
3. Press and release the
VCR button (The INDI-
CATOR LIGHT will blink
then remain lit.
4. Enter the code using
the Number Buttons.
After your code is
entered, the INDICATOR
LIGHT will turn off. If the
code is not valid, the
INDICATOR LIGHT will
blink. Check the code list
and repeat process.
5. Aim the remote at
your VCR and press the
ON•OFF button. Your
VCR should turn off.
NOTE: If your VCR does
not respond, try all the
codes for your brand. If
the codes do not work,
or your brand is not listed,
try the Code Search
method on Page 12.
6. With your VCR on, press CHAN+ (CHANNEL
UP). If the VCR responds, no further programming is
required.
7. Enter your code here
for easy reference.
94940 Revised Size 10/18/02 12:22 PM Page 8
8
Programming For DVD
Most GE, RCAand ProScan DVD systems will not
require programming. Check to see if your DVD sys-
tem responds to the remote before you begin pro-
gramming.
1. Manually turn on the DVD system. Find the three
digit code for your DVD system at the back of the
instructions.
2. Press and hold the
CODESEARCH button
until the INDICATOR
LIGHT lights, then
release the CODE
SEARCH button.
3. Press and release the
DVD button (The INDI-
CATOR LIGHT will blink
then remain lit.
4. Enter the code using
the Number Buttons.
After your code is
entered, the INDICATOR
LIGHT will turn off. If the
code is not valid, the
INDICATOR LIGHT will
blink. Check the code list
and repeat process.
5. Aim the remote at
your DVD system and
press the ON•OFF but-
ton. Your DVD system
should turn off.
6. If the DVD System responds, no further
programming is required.
NOTE: If your DVD does not respond, try all the
codes for your brand. If the codes do not work,
or your brand is not listed, try the Code Search
method on Page 12.
7. Enter your code here
for easy reference.
CODELIST
94940 Revised Size 10/18/02 12:22 PM Page 9
9
Programming For DBS Satellite System
Most GE, RCAand ProScan Satellite systems will not
require programming. Check to see if your DBS
Satellite system responds to the remote before you
begin programming.
1. Manually turn on the DBS system. Find the three
digit code for your DBS
system at the back of the instructions.
2. Press and hold the
CODESEARCH button
until the INDICATOR
LIGHT lights, then
release the CODE SEARCH
button.
3. Press and release the
CBL/SAT button (The INDI-
CATOR LIGHT will blink
then remain lit.
4. Enter the code using the
Number Buttons. After your
code is entered, the INDI-
CATOR LIGHT will turn off.
If the code is not valid, the
INDICATOR LIGHT will
blink. Check the code list
and repeat process.
5. Aim the remote at your
DBS system and press the
ON•OFF button. Your DBS
system should turn off.
6. With your DBS System
on, press CHAN+ (CHAN-
NELUP). If the satellite sys-
tem responds, no further
programming is required.
NOTE: If your DBS system does not respond, try all
the codes for your brand. If the codes do not work,
or your brand is not listed, try the Code Search
method on Page 12.
7. Enter your code here
for easy reference.
CBL/SAT
CBL/SAT CODE
94940 Revised Size 10/18/02 12:22 PM Page 10
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Mando a distancia de GE
GE
GE 37123 Manual de usuario
GE
GE 45633 Manual de usuario
GE
GE RM94904 Manual de usuario
GE
GE 94948 Manual de usuario
GE
GE 45600 Manual de usuario
GE
GE UltraPro 44220 Manual de usuario
GE
GE 25006 Manual de usuario
GE
GE GE SmartHome Remote Manual de usuario
GE
GE YR-HQ Manual de usuario
GE
GE 94931 Manual de usuario
