GE RM94925 Manual de usuario
Universal
Remote Control
RM94925
INSTRUCTION
MANUAL
94925 Revised Size 2/25/02 4:00 PM Page 1
1
Thank you for purchasing the GE Universal Remote
Control. This product is designed to provide years of
service operating a wide variety of video and audio
equipment.
Please retain this guide for future reference.
Table of Contents
Install the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Button Description . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4
Programming for TV . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Programming for VCR . . . . . . . . . . . . . . . . . . . . . . . . . .6
Programming For DVD . . . . . . . . . . . . . . . . . . . . . . . . .7
Programming For DBS System . . . . . . . . . . . . . . . . . . .8
Programming For Cable . . . . . . . . . . . . . . . . . . . . . . . .9
Programming For Audio . . . . . . . . . . . . . . . . . . . . . . .10
Programming For AUX . . . . . . . . . . . . . . . . . . . . . . . .11
Operating Audio Function . . . . . . . . . . . . . . . . . . .12-13
Sleep Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Menu Functions . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
Programming With Code Search . . . . . . . . . . . . . . . .16
Identifying Codes For Your Remote . . . . . . . . . . .16-17
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Device Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39-43
This Universal Remote Control is already programmed
for most GE, RCA and ProScan TVs, VCRs, DBS
Systems, DVD Players, and Audio/Video Receivers.
NOTE: For users of GE, RCA and ProScan DBS
Products, older DBS models require that the DISPLAY
Button on this remote be used to make program selec-
tions. Use the SELECT Button for making program
selections on newer GE, RCAand ProScan DBS models.
Battery Installation
Your Universal Remote Control requires 2 AAA alka-
line batteries.
To install the batteries:
1. Turn the remote over and push down on the cover
and slide it off.
2. Insert the batteries, matching the batteries to the (+)
mark inside the battery case.
3. Slide the battery cover back into place.
NOTE: Programmed codes will remain in memory for
a short period of time allowing for battery replacement.
If batteries have been dead for a prolonged period of
time, reprogramming may be required.
94925 Revised Size 2/25/02 4:00 PM Page 2
2
Button Description
INDICATOR LIGHT
The Indicator Light flashes to show that the remote is
working.
ON•OFF
The ON•OFF button operates the same as your origi-
nal remote.
NOTE: Some GE, RCA and ProScan models require
you to press the device button to turn the device on
and the ON•OFF button to turn the device off.
TV, VCR, DVD, SAT, AUDIO, AUX, CBL
The TV, VCR, DVD, SAT, AUDIO-AUX, and CBL but-
tons are used to select the device you want to control.
VOL & CHAN
The VOL (Volume) and CHAN (Channel) buttons
increase or decrease the channel numbers or
volume.The CHANNEL buttons also control the SKIP
functions for DVD and CDPlayer.
MUTE
Mutes volume on the TV.
PREV CHAN
The PREV CHAN button allows you to go to the pre-
vious channel you selected. Operates the same as Last
Channel, Go Back or Recall on your original remote.
CODE SEARCH
Used to program the remote or to search through
codes.
GUIDE
Brings up the on-screen TV program guide if your TV
has that feature.
DISP
Display Button shows the date and the time if your TV
or VCR has that feature.
NAVIGATION BUTTONS & SELECT
Used to move through on-screen menuing and guides.
With some DBS models the DISP button should be
used to select the highlighted item. Use the navigation
buttons to move the highlighted choice up, down, left
or right.
MENU•PROG
Brings up the Main Menu. If you already in the menu
system, press SELECT to select a highlighted choice.
Use the arrows buttons to move through the Menu
Selection.
CLEAR
Removes the on screen display to return to normal
viewing.
94925 Revised Size 2/25/02 4:00 PM Page 3
3
0-9
The number buttons operates the same as on your orig-
inal remote, and are used for entering device codes.
ENTER
The ENTER button is used to complete channel selec-
tion for some brands of TV. It is also used to complete
the code entry process.
TV/VCR
The TV/VCR button operates the TV/VCR function of
your TV.
REW, PLAY, FF, REC, STOP, PAUSE
These buttons operate the same as on your original
VCR or remote.You must press the REC button twice to
begin recording. The REW and FF buttons also control
the Reverse and Forward functions for DVD and CD
Player.
PIP, SWAP & INPUT
PIP(Picture-in-Picture) and SWAP operate your televi-
sion’s Picture-in-Picture features. INPUT selects the
video input of your TV if equipped with this feature.
SLEEP
The SLEEP button allows you to set a time for you to
turn off your TV automatically.
Button Description For Audio Operation
Press AUDIO device button to enable the AUDIO
MODE Audio functions indicated by pink descriptions
LEVEL+/LEVEL-
Sets the level of the speakers during test tone mode.
DSP ON•OFF
Enables the receiver’s Digital Sound Processing Mode.
DSP MODE
When the DSP mode is enabled, pressing this button
allows the user to toggle through the various DSP
modes.
CD, TAPE, TUNER, TV, VIDEO
The CD, TAPE, TUNER, TV and VIDEO buttons are
used to directly select the device you want to control.
(Works in AUDIO mode).
AM•FM
The AM•FM button allows you to select the AM•FM
band on your audio receiver.
FUNCTION
Toggles the different audio input devices. The number
buttons also select the function labeled below the but-
tons when in AUDIO mode.
DELAY-, ON, DELAY+
Increases or decreases the delay between the surround
and main speakers when the receiver is in the surround
sound mode.
94925 Revised Size 2/25/02 4:00 PM Page 4
4
ON•OFF, SURR. MODE
ON•OFF SURR. toggles the surround modes on and
off. SURRMODE toggles through the receiver’s vari-
ous surround sound mode settings.
FRONT, CENTER, REAR, TEST
Adjust the levels of the front, center, and rear speakers
respectively. The test tone must be enabled first by
pressing the TEST button.
PRESET
Used to operate preset channels while in the AUDIO
mode.
94925 Revised Size 2/25/02 4:00 PM Page 5
5
Programming For TV
Most GE, RCAand ProScan TVs will not require pro-
gramming. Check to see if your TV responds to the
remote before you begin programming.
1. Manually turn on the
TV. Find the three digit code
for your TV in the code list
below.
2. Press and hold the
CODESEARCH button
until the INDICATOR
LIGHT lights, then
release the CODE SEARCH
button.
3. Press and release the TV
button (The INDICATOR
LIGHT will blink then
remain lit.
4. Enter the code using the
Number Buttons. After your
code is entered, the INDI-
CATOR LIGHT will turn
off. If the code is not valid,
the INDICATOR LIGHT
will blink. Check the code
list and repeat process.
5. Aim the remote at your
TV and press the ON•OFF
button. Your TV should turn
off.
NOTE: If your TV does not
respond, try all the codes for
your brand. If the codes do
not work, or your brand is
not listed, try the Code
Search method on Page 16.
6. With your TV on, press CHAN+ (CHANNELUP).
If the TV responds, no further programming is
required.
7. Enter your code here for easy reference.
TV CODE LIST
94925 Revised Size 2/25/02 4:00 PM Page 6
6
Programming For VCR
Most GE, RCAand ProScan VCRs will not require
programming. Check to see if your VCR responds to
the remote before you begin programming.
1. Manually turn on the
VCR. Find the three digit
code for your VCR in the
code list below.
2. Press and hold the
CODESEARCH button
until the INDICATOR
LIGHT lights, then
release the CODE
SEARCH button.
3. Press and release the
VCR button (The INDI-
CATOR LIGHT will blink
then remain lit.
4. Enter the code using
the Number Buttons.
After your code is
entered, the INDICATOR
LIGHT will turn off. If the
code is not valid, the
INDICATOR LIGHT will
blink. Check the code list
and repeat process.
5. Aim the remote at
your VCR and press the
ON•OFF button. Your
VCR should turn off.
NOTE: If your VCR does
not respond, try all the
codes for your brand. If
the codes do not work,
or your brand is not list-
ed, try the Code Search
method on Page 16.
6. With your VCR on, press CHAN+ (CHANNEL
UP). If the VCR responds, no further programming is
required.
7. Enter your code here for easy reference.
94925 Revised Size 2/25/02 4:00 PM Page 7
7
Programming For DVD
Most GE, RCAand ProScan DVD systems will not
require programming. Check to see if your DVD sys-
tem responds to the remote before you begin pro-
gramming.
1. Manually turn on the
DVD system. Find the
three digit code for your
DVD system in the code
list below.
2. Press and hold the
CODESEARCH button
until the INDICATOR
LIGHT lights, then
release the CODE
SEARCH button.
3. Press and release the
DVD button (The INDI-
CATOR LIGHT will blink
then remain lit.
4. Enter the code using
the Number Buttons.
After your code is
entered, the INDICATOR
LIGHT will turn off. If the
code is not valid, the
INDICATOR LIGHT will
blink. Check the code list
and repeat process.
5. Aim the remote at
your DVD system and
press the ON•OFF but-
ton. Your DVD system
should turn off.
6. If the DVD System responds, no further
programming is required.
NOTE: If your DVD does not respond, try all the
codes for your brand. If the codes do not work,
or your brand is not listed, try the Code Search
method on Page 16.
7. Enter your code here for easy reference.
CODELIST
94925 Revised Size 2/25/02 4:00 PM Page 8
8
Programming For DBS Satellite System
Most GE, RCAand ProScan Satellite systems will not
require programming. Check to see if your DBS
Satellite system responds to the remote before you
begin programming.
1. Manually turn on the
DBS system. Find the three
digit code for your DBS
system in the code list
below.
2. Press and hold the
CODESEARCH button
until the INDICATOR
LIGHT lights, then
release the CODE SEARCH
button.
3. Press and release the
DBS button (The INDICA-
TOR LIGHT will blink then
remain lit.
4. Enter the code using the
Number Buttons. After your
code is entered, the INDI-
CATOR LIGHT will turn off.
If the code is not valid, the
INDICATOR LIGHT will
blink. Check the code list
and repeat process.
5. Aim the remote at your
DBS system and press the
ON•OFF button. Your DBS
system should turn off.
6. With your DBS System
on, press CHAN+ (CHAN-
NELUP). If the satellite sys-
tem responds, no further
programming is required.
NOTE: If your DBS system does not respond, try all
the codes for your brand. If the codes do not work,
or your brand is not listed, try the Code Search
method on Page 16.
7. Enter your code here for easy reference.
SATELLITE CODE LIST
94925 Revised Size 2/25/02 4:00 PM Page 9
9
Programming For Cable
1. Manually turn on the Cable Box.
Find the three digit code for your Cable Box
in the code list below.
2. Press and hold the
CODESEARCH but-
ton until the INDICA-
TOR LIGHT lights,
then release the CODE
SEARCH button.
3. Press and release
the CBLbutton (The
INDICATOR LIGHT
will blink then
remain lit.
4. Enter the code
using the Number
Buttons. After your
code is entered, the
INDICATOR LIGHT
will turn off. If the
code is not valid, the
INDICATOR LIGHT
will blink. Check the
code list and repeat
process.
5. Aim the remote at
your CABLE and press
the ON•OFF button.
Your CABLE should
turn off.
6. With your Cable
Box on, press CHAN+
(CHANNELUP). If
the Cable Box
responds, no further
programming is
required.
NOTE: If your Cable Box does not respond, try all the
codes for your brand. If the codes do not work,
or your brand is not listed, try the Code Search
method on Page 16.
7. Enter your code here for easy reference.
CABLE BOX CODE LIST
94925 Revised Size 2/25/02 4:00 PM Page 10
Tabla de contenidos
Idiomas:
Otros manuales de Mando a distancia de GE
GE
GE 24116 - 4 - Device Universal Remote Manual de usuario
GE
GE 94906 Manual de usuario
GE
GE HC-TX10 Manual de usuario
GE
GE 37123 Manual de usuario
GE
GE 45600 Manual de usuario
GE
GE 45600 Manual de usuario
GE
GE Cync CWLRMDMBWM1 Manual de usuario
GE
GE RM94940 Manual de usuario
GE
GE YR-HQ Manual de usuario
GE
GE 94901 Manual de usuario
