GE 25006 Manual de usuario

Universal Remote

Instruction Manual

Control Remoto Universal

Manual de Instrucciones

25006

7252

Introduction

Congratulations on your purchase of the GE Universal

Remote Control. The GE Universal Remote Control

is one of the most easy-to-use remote controls

available today. With the GE Universal Remote

Control, juggling multiple remote controls is a thing of

the past! Your GE Universal Remote Control controls

multiple devices, including the most popular brands

of TV, VCR, DVD, CBL and SAT. The GE Universal

Remote Control is easy to use, easy to program,

and it gives you total control — at the touch of your

ﬁngertips!

IMPORTANT: SAVE THIS MANUAL AND CODE LIST

FOR FUTURE REFERENCE

Introduction..................................................................................... 2

Setup .................................................................................................. 3

Battery Installation............................................................... 3

Battery Precautions.............................................................. 3

Battery Saver........................................................................... 3

Code Saver ............................................................................... 3

Button Functions ................................................................... 4

Programming Your Remote..................................................... 6

Direct Code Entry................................................................... 6

Auto Code Search ................................................................. 8

Using Your Remote ....................................................................10

Controlling Combo Devices............................................10

Using SHIFT............................................................................10

Master Volume Feature....................................................11

Code Identiﬁcation .............................................................12

Reset to Factory Settings.................................................12

Troubleshooting..........................................................................13

Warranty ........................................................................................14

FCC Statement.............................................................................15

Table of Contents

Scan this to view remote

setup video

Mira a ver el video de

instalación remota

http://www.jascoproducts.com/remote

Your universal remote requires two (2) AAA batteries

(not included). Alkaline batteries are recommended.

Battery Installation

1. On the back of the remote, push in on the textured

surface and slide battery cover downward to

remove.

2. Match the (+) and (-) marks on the batteries to the

(+) and (-) marks inside the battery compartment,

then insert two (2) AAA batteries. Be sure to use

fresh batteries.

3. Position battery cover slightly below opening and

push upward to lock into place.

NOTE: If your remote stops operating properly,

replace the batteries with new ones. The remote will

retain the codes you have programmed for up to 10

minutes after the batteries are removed.

Battery Precautions

• Donotmixoldandnewbatteries.

• Donotmixalkaline,standard(carbon-zinc),or

rechargeable (Ni-Cd, Ni-MH, etc.) batteries.

• Alwaysremoveold,weakorworn-outbatteries

promptly and recycle or dispose of them in

accordance with local and national regulations.

Battery Saver

Your remote automatically turns off if the buttons are

depressed more than 8 seconds. This will save your

batteries should your remote get stuck in a place

where the buttons remain depressed (e.g., between

the sofa cushions).

Code Saver

You will have up to 10 minutes to change the

batteries in your remote without losing codes you

have programmed. However, do not press any

buttons until batteries are installed in the remote. If

buttons are pressed without batteries in the remote,

all codes will be lost.

Setup

RECORD, PLAY, STOP,

REW(rewind), FF(fast

forward), PAUSE

TV, CBL/SAT,

DVR/AUX, DVD

Selects device

to control.

Indicator Light

DOT: Used to select digital

channels, e.g., 2.3.

INPUT Selects the video

inputs from available

viewing sources.

Button Functions

MENU Press and release

SHIFT/SETUP then MENU/

INFO to display the Menu

on the TV. See “Using

SHIFT for Menu and

Navigation” description

on Page 10 for more

information.

INFO Displays/selects

on-screen channel

information.

ABCD (Red, Green, Yellow

& Blue) Allows access to

additional features for DVR's,

Cable Box, Satellite, Blu-ray,

etc... (additional features vary

by device type and brand,

see device owner's manual

for information).

ENTER

For some TV models, used after

direct channel number entry

to immediately change to the

selected channel.

VOLUME UP/DOWN

Changes the volume

level of the device,

normally the TV.

NUMBERS

Enter numbers for direct

channel selection. Some

devices require ENTER

to be pressed after

channel selection.

ON•OFF Turns

devices On or Off.

CHANNEL UP/DOWN

Changes the channels.

Button Functions, cont.

SETUP Used to setup the remote,

and for code search function.

SHIFT Press and release to access buttons

labeled in reverse print (GUIDE, MENU,

EXIT). See “Using SHIFT for Menu and

Navigation” description on Page 10

for more information.

MUTE Turns off the

TV sound while the

picture remains.

OK Selects menu

items for the device

you are controlling.

LAST Returns to

previous channel

EXIT Exits On-Screen

Menus and/or

Returns to previous

On-Screen selection.

Programming Your Remote

Your GE universal remote control is designed to

control multiple audio/video devices such as a TV,

DVD, DVR, satellite, cable and audio device using

only one remote. To use this remote, you will need to

program it to control the devices of your choice. There

are two ways to program the remote - direct code

entry or auto code search.

Direct Code Entry (Recommended)

1. Locate the Remote Code List. Find

the DEVICE CATEGORY you wish to

program (for example TV, DVD, CBL/

SAT, DVR/AUX) and then ﬁnd the

BRAND of that device. Circle all the

codes under that brand. Example: For

a GE TV, locate the TV code section

then circle all of the GE TV codes.

2. Manually turn on the device you wish

to control.

3. Press and hold the SETUP button

until the red indicator light stays on

(approximately 2 seconds) and then

release the SETUP button.

4. Press and release the desired device

button on the remote (TV, DVD, CBL/

SAT, DVR/AUX). The red indicator will

blink once and then remain on.

5. Enter the ﬁrst 4-digit code previously

found in the code list using the

number buttons on the remote. If the

code entered is a valid code, the red

indicator light will turn off. If the code

entered is not a valid code, the red

indicator light will ﬂash and remain on

allowing you to re-enter the code.

Note: If no buttons are pressed for 35

seconds, the remote will exit the SETUP

mode and you will have to start over.

Programming Your Remote, cont.

6. Point the remote at the device. Press

the POWER button—if the device

turns off, no further programming is

required for that device. If the device

does not turn off, return to step 3 and

use the next code found in the code

list. Continue this process until a code

for your device is found.

7. Repeat this process for each device

(for example TV, DVD, CBL/SAT, DVR/

AUX) in your home entertainment

system you wish to control.

Programming Notes

• Ifyourdevicedoesnotrespondtotheremoteafter

trying all codes listed or your brand is not listed in

the code list, use the Auto Code Search method to

program your remote.

• Sometimestherstcodethat“works”withyour

device may operate only a few functions of your

device. There may be another code in the code

list that performs more functions. Try other codes

from the code list for more functionality.

• WiththeDirectCodeEntrymethod,youcan

program any device button to control any device

in your home entertainment system.

For example, you can use the DVR/AUX device

button to control an audio receiver or a DVD, VCR,

satellite device, etc.

• Forcombinationdevices,youmayhavetoentera

code for each device. For example, for a VCR/DVD

device, you may have to enter a code for the DVD

under the DVD button and enter a code for the

VCR using a different device button on the remote.

• Writedownthecodefoundtooperateyourdevice

for future reference.

Programming Your Remote, cont.

Auto Code Search

The Auto Code Search searches automatically

through the codes stored in this remote. Read all the

following steps prior to starting the auto code search

as you will need to be prepared to lock-in the proper

code when found.

1. Manually turn on the device you wish

to control.

2. Press and hold the SETUP button

until the red indicator light stays on

(approximately 2 seconds) and then

release the button.

3. Press and release the desired device

button on the remote (TV, DVD, CBL/

SAT, DVR/AUX) for the type of devices

you wish to control. The red indicator

will blink once and then remain on.

4. Point the remote at the device and

press and release the POWER button

(for TV) or PLAY button (for DVD, VCR,

etc.) to start the search. The red

indicator will ﬂash (approximately

every 2 seconds) as the remote

searches. Note: The remote must be

pointed at the device for the duration of

this search.

5. Place your ﬁnger on the #1 button so

you are prepared to lock-in the code.

6. When the device shuts off or begins

playing, press the #1 button to lock-in

the code. The red indicator light will

turn off. Note: You have approximately

two seconds after the device shuts off

or begins playing to lock-in the code.

7. Point the remote at the device and

check to see if the remote operates the

device as desired. If it does, no further

programming is required for that

device. If it does not, return to step 2

and start the auto code search again.

Programming Your Remote, cont.

8. Repeat this process for each device (for example

TV, DVD, SAT, AUX) in your home entertainment

system you wish to control.

Programming Notes

• Thisprocessmaytakeseveralminutesasthe

remote contains many codes.

• WhenusingtheAutoCodeSearchprogramming

method, the device button corresponding to

the type of device you want to control must be

selected (for example, the TV device button must

be selected in step 3 if you want to control a TV,

the DVD device button for a DVD player, etc.)

• TheSETUP button can be used during the search

process to reverse the direction of the search of

the remote codes. For example, if you miss the

code for your device and the remote is continuing

to search (as indicated by the blinking red light),

press the SETUP button and the code search will

reverse direction and return to the code.

• Sometimestherstcodethat“works”withyour

device may operate only a few functions of your

device. There may be another code in the code

list that performs more functions. Continue the

auto code search as directed above until the best

code is found.

Using Your Remote

For MENU, press and release

SHIFT/SETUP then INFO/MENU.

For OK, press and release

SHIFT/SETUP then MUTE/OK.

For EXIT, press and release

SHIFT/SETUP then LAST/EXIT.

For Up, Down, Left or Right Navigation,

press and release SHIFT/SETUP

followed by the respective Channel or

Volume button.

SPECIAL NOTE: Remote will stay in shift mode

until the SHIFT button is pressed again, or until 10

seconds of inactivity. The red indicator light will

blink when the remote is in shift mode.

Using SHIFT for Menu and Navigation

The SHIFT button allows access to more than one

function for certain buttons.

Use the SHIFT/SETUP button prior to accessing

the MENU, GUIDE OK, EXIT and Navigation functions,

for example:

Controlling Combo Devices

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/

VCR, etc.) will require you to set up two different Mode

buttons to control both parts of the Combo device.

For example, if you have a TV/DVD Combo, you might

need to set up one code under the TV button to

control the TV part AND a separate code (under any

other Mode button) to control the DVD part.

Tabla de contenidos

Idiomas:

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación

Invacare

Invacare G91S Manual de usuario