GE WIU-4 Manual de usuario

Security

U.S.

T 888 GE SECURITY (1 888 437 3287)

F 561 998 6224

Asia

T 852 2907 8108

F 852 2142 5063

Australia

T 61 3 9259 4700

F 61 3 9259 4799

Europe

T 32 2 725 11 20

F 32 2 721 86-13

Latin America

T 305 593 4301

F 305 267 4300

www.gesecurity.com

460487001F/11-05

Wiegand Interface Unit Four-State (WIU-4)

Installation Manual

This document may not be copied or otherwise reproduced, in whole or in part,

except as specifically permitted under US and international copyright law,

without the prior written consent from GE.

Document number/460487001F (November 2005).

Disclaimer THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT

NOTICE. GE ASSUMES NO RESPONSIBILITY FOR INACCURACIES OR OMISSIONS

AND SPECIFICALLY DISCLAIMS ANY LIABILITIES, LOSSES, OR RISKS, PERSONAL OR

OTHERWISE, INCURRED AS A CONSEQUENCE, DIRECTLY OR INDIRECTLY, OF THE

USE OR APPLICATION OF ANY OF THE CONTENTS OF THIS DOCUMENT. FOR THE

LATEST DOCUMENTATION, CONTACT YOUR LOCAL SUPPLIER OR VISIT US ONLINE

AT WWW.GESECURITY.COM.

This publication may contain examples of screen captures and reports used in

daily operations. Examples may include fictitious names of individuals and

companies. Any similarity to names and addresses of actual businesses or

persons is entirely coincidental.

Trademarks

and patents

GE and the GE monogram are registered trademarks of General Electric.

Wiegand Interface Unit-Four State (WIU-4) product and logo are trademarks of

GE Security.

Other trade names used in this document may be trademarks or registered

trademarks of the manufacturers or vendors of the respective products.

Intended use Use this product only for the purpose it was designed for; refer to the data sheet

and user documentation. For the latest product information, contact your local

supplier or visit us online at www.gesecurity.com.

FCC

compliance

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful inter-

ference to radio communications.

You are cautioned that any changes or modifications not expressly approved

by the party responsible for compliance could void the user's authority to

operate the equipment.

Regulatory

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Radio interference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Electrostatic discharge (ESD) precaution . . . . . . . . . . . . . . . . . . . . . . . . .2

Product features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

System requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Mounting the WIU-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Configuring the WIU-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

J3: Door and REX switch connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

J4: Door and REX supervision connector . . . . . . . . . . . . . . . . . . . . . . . .10

J5: Reserved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

J6: Reader interface connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

J7: Reserved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

J8: Micro interface connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

J9: Reserved . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

J10: Door strike relay connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

LED indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Connecting the WIU-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Wiring diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Testing the WIU-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Troubleshooting the WIU-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Regulatory approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

UL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

CE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Wiegand Interfact Unit Four State (WIU-4)

Installation Manual

Figures

Figure 1. Mounting instructions .................................................................. 7

Figure 2. WIU-4 connectors and jumpers.............................................. 9

Figure 3. Sample WIU-4 configuration..................................................14

Figure 4. WIU-4 to Micro/5 8RP board...................................................15

Figure 5. WIU-4 to Micro/PX-2000, PXN-2000, or

M2000PXNplus interface ..........................................................16

Introduction 1

Introduction

The Wiegand Interface Unit-Four State (WIU-4) board features a

Wiegand to F/2F data converter, which can accommodate both

conventional and proprietary Wiegand reader protocols, and

includes an 8 Amp relay for door strike control (entrance/exit)

activity. It provides the communications interface that enables

support of up to 16 Wiegand-output readers.

When combined with most conventional Proximity, Mifare®, and

ISO-15693 Wiegand-output readers, the WIU-4 reports

immediate alarm notification of short circuit, cut line, open

circuit, or closed circuit conditions to the GE access control

system.

Wiegand Interface Unit Four State (WIU-4)

Installation Manual

Safety

Radio interference

Electrostatic discharge (ESD) precaution

WARNING: This is an FCC Class A product. In a domestic

environment, this product may cause radio

interference, in which case, the user may be

required to take adequate measures.

WARNING: Circuit board components are vulnerable to damage

by electrostatic discharge (ESD). ESD can cause

immediate or subtle damage to sensitive electronic

parts. An electrostatic charge can build up on the

human body and then discharge when you touch a

board. A discharge can be produced when walking

across a carpet and touching a board, for example.

Before handling any board, make sure you dissipate

your body’s charge by touching ground. This

discharges any static electricity build-up.

Product features 3

Product features

The WIU-4 provides the following:

• Conversion of multiple Wiegand formats into GE

supervised F/2F format.

• Junction box capabilities with removable connectors for

ease of wiring.

• Built-in door strike relay with surge protecting diodes.

• Red LED, green LED, and beeper control outputs.

• Supports reader tamper and external tamper inputs.

• Self-resetting fuse protection on all power and signal

outputs.

• Options for supervised or unsupervised Door DI and

request-to-exit (REX) DI inputs.

• Built-in surge protection circuitry for data lines.

• Four built-in LEDs to help with installation and

troubleshooting.

• Supports Wiegand formats up to 64 bits.

• Supports most 8 bit keypad reader output formats.

Note: Do not use the WIU-4 with a 2SRP supervised reader processor

board/microcontroller configuration.

Wiegand Interface Unit Four State (WIU-4)

Installation Manual

System requirements

For UL compliant installation notes, refer to “UL Listed Installations” on

page 20.

Host software • Secure Perfect®Edition 3.0 or later

•PicturePerfect

™1.7 or later

Microcontrollers • Micro/5-PX with 2RP or 8RP

•Micro/5-PXNwith2RPor8RP

•M5PXNplus

• Micro/PX-2000

• Micro/PXN-2000

• M2000PXNplus

• M3000PXNplus

Reader support • Wiegand data output up to 64 bits

• Most 8 bit keypad readeroutput formats

Wiegand data

formats

•26-bit

•32-bit

• 35-bit Corporate 1000

•37-bit

• 40-bit GE formats

• Custom Wiegand formats up to 64 bits

Technical specifications 5

Technical specifications

For UL compliant installation notes, refer to “UL” on page 20.

Operating temperature

range

-31 F (-35 C) to +150 F (+66 C)

Relative humidity 5% to 95% (non-condensing)

Physical dimensions

(HxWxD)

3.1" (78.74 mm) x 2.5" (63.50 mm) x 0.644"

(16.35 mm)

Index of protection IP00

Input voltage range 9 to 16 VDC

Power consumption 40 mA @ 12 VDC (no reader attached)

Cable specifications*

* GE recommends using shielded cable for all installations.

Belden 8725 or equivalent, 20 AWG minimum

Maximum cabling distance

WIU-4 to micro:**

WIU-4 to reader:***

** WIU-4 to micro: The maximum cabling distance of 1,000 ft (304.8 meters) is

influenced by wire gauge, reader power requirements, and the 12 VDC level from

the microcontroller.

*** WIU-4 to reader: The maximum cabling distance of 250 ft (76.20 meters) is

influenced by wire gauge, reader power requirements, minimum input voltage at

the reader when using the 12 VDC from the WIU-4 (originally from the micro), and

the cabling between the WIU-4 and micro.

1000 ft (304.8 m) @ 12 VDC with 20 AWG cable

250 ft (76.2 m) @ 12 VDC with 20 AWG cable

Door strike relay****

**** The life of the relay decreases as the current switched by the contacts is

increased. Use low current door strikes for high traffic doors to maximize the

relay life. Use an external relay for high current applications.

8.0 A @ 30 VDC maximum

Agency approvals FCC Class A part 15

UL 294

Wiegand Interface Unit Four State (WIU-4)

Installation Manual

Parts list

•WIU-4

• Mounting hardware kit

• Installation manual

Refer to the GE product catalog for part numbers and ordering

information.

Installation overview

The following is the general sequence of steps to follow when

installing the Wiegand Interface Unit-4. Each step is explained in

further detail in the sections that follow:

1. Mount the WIU-4.

Refer to “Mounting the WIU-4” on page 7.

Note: The WIU-4 must be mounted indoors, in a protective enclosure or

standard 2-gang electrical box (Installer supplied) as shown in

Figure 1.

2. Configure the WIU-4.

Refer to “Configuring the WIU-4” on page 8.

3. Connect the WIU-4.

Refer to “Connecting the WIU-4” on page 14.

4. Test the WIU-4.

Refer to “Testing the WIU-4” on page 17.

Tabla de contenidos

Otros manuales de Unidad de control de GE

GE Tetra GECLPS5-2 Manual de usuario

GE B90 Manual de usuario

GE C-800 Series Manual de usuario

GE Baker Hughes Masoneilan 31000 Series Manual de usuario

GE EntelliGuard TU Manual de usuario

GE VersaMax IC200ALG630 Manual de usuario

GE TLE Scalable 150 Manual de usuario

GE EX2100 Manual de usuario

GE Masoneilan 469 Series Manual de usuario

GE Evolution Series E9000 Manual de usuario

GE VME DLAN Manual de usuario

GE SX TRANSISTOR CONTROL IC3645SR4U404N2 Manual de usuario

GE Masoneilan 48000 Series Manual de usuario

GE PACSystems RX3i IC695ETM001-JW Manual de usuario

GE CR194 Manual de usuario

GE WH18X28174 Guía de configuración

GE S-500 Series Manual de usuario

GE Reason RT430 Manual de usuario

GE IC3645SR4W606N6 Manual del propietario

GE IC3645SR7T405T5 Manual de usuario

GE NetworX Series Manual de usuario

GE VARIVENT S Series Manual de usuario

GE GEH-5201 Manual de usuario

GE VersaSafe VersaPoint IC220SDL840 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario