GE IC695CMM002CA-EJ Manual de usuario

Important Product Information

PACSystems* RX3i

IC695CMM002-EJ and IC695CMM002CA-EJ

IC695CMM004-EJ, IC695CMM004CA-EJ, and IC695CMM004LT-EJ

GFK-2461N

Serial Communications Modules

April 2018

PACSystems* RX3i Serial Communications modules expand the serial

communications capabilities of the RX3i system.

Serial Communications module IC695CMM002 provides two independent,

isolated serial ports. Serial Communications module IC695CMM004, illustrated at

right, provides four independent, isolated serial ports.

Up to six Serial Communications modules can be located in the main

PACSystems RX3i backplane1.

The IC695CMM00xCA modules are the conformal-coated versions of the

IC695CMM00x modules.

The IC695CMM004LT version is for low temperature applications (-40°C).

Each port can be configured for MODBUS Master, MODBUS Slave, CCM Slave,

DNP3 Master, DNP3 Slave, or Serial I/O protocol. If any port is configured for

DNP3 Master or Slave, the other ports on the module can only be configured for

DNP3 Master or Slave.

For modules with firmware version 1.32 or later, half-duplex flow control can be

configured using Machine Edition Release 5.90, SP1, SIM 6 or later. Otherwise,

flow control defaults to full-duplex.

Additional module features include:

•Port-to-port isolation and port-to-backplane isolation

•RS-232, RS-485/422 communication, software-selected

•Hardware handshake: RTS/CTS, RFR/CTS for RS-232

•Selectable Baud Rates: 1200, 2400, 4800, 9600, 19.2K, 38.4K, 57.6K, 115.2K

•Module fault status reporting (Watchdog, Ram Fail, Flash Fail)

•Module identity and status reporting, including LED status indicators

•Meets CE, UL/CUL 508 and 1604, and ATEX requirements

•Flash memory for future upgrades

These modules must be located in an RX3i Universal Backplane.

RX3i Serial Communications can be hot-inserted and removed following the

instructions in the most recent version of the PACSystems RX3i System Manual,

GFK-2314.

For complete installation information, please refer to RX3i and Series 90-30

Installation and Maintenance Requirements document, GFK-2975.

Figure 1: CMM004 Front

View

*Indicates a trademark of General Electric Company and/or its subsidiaries. All other trademarks are the property of

their respective owners.

Not compatible with Rackless CPUs, such as CPE400.

RX3i Serial Communications Modules

GFK-2461N

Release Information

Release 2.02 is a new firmware release implementing a unique system ID for each module to support future RX3i

expansion. No change in functionality, performance, or compatibility.

Release History

Release

Firmware

Version

Upgrade Kit

Comments

IC695CMM002-EJ

IC695CMM004-EJ

2.02

41G2459-FW01-000-A2

41G2460-FW01-000-A2

This FW change implements a unique system ID for

each module to support future RX3i expansion. No

change in functionality, performance, or compatibility.

IC695CMM002-EH

IC695CMM004-EH

2.01

41G2459-FW01-000-A1

41G2460-FW01-000-A1

This FW change fixes a bug in the RS232 serial ASCII

communication mode.

IC695CMM002-EG

IC695CMM004-EG

2.00

41G2459-FW01-000-A0

41G2460-FW01-000-A0

This HW/FW change addresses a component

obsolescence issue and meets EU RoHS compliance.

IC695CMM002-DF

IC695CMM004-DF

1.34

N/A

This change updated compliance markings on the

packaging.

IC695CMM002-CF

IC695CMM004-CF

1.34

N/A

This change addresses a component obsolescence

issue. No change in functionality, performance or

compatibility.

IC695CMM002-BF

IC695CMM004-BF

1.34

N/A

Label change only. No change in functionality,

performance or compatibility.

IC695CMM002-AF

IC695CMM004-AF

1.34

44A753277-G06

44A753278-G06

Adds DNP3.0 Master and Slave Unsolicited Reporting

functionality. The release also adds the ability to

configure the DNP3.0 Slave Analog Input Event Variation

and fixes three issues in the DNP3.0 firmware

IC695CMM002-AE

IC695CMM004-AE

1.32

44A753277-G05

44A753278-G05

See GFK-2461E for new features and problems

resolved.

IC695CMM002-AD

IC695CMM004-AD

1.30

44A753277-G04

44A753278-G04

Supports Serial Protocol Language (SPL) scripting.

Corrects DNP3 Slave Bit Write issue. Please refer to

M050803 - IC695CMM002_004 Product Safety Bulletin

for more information.

IC695CMM002-AC

IC695CMM004-AC

1.20

44A753277-G03

44A753278-G03

Supports DNP3 Master and DNP3 Slave Protocol

IC695CMM002-AB

IC695CMM004-AB

1.10

44A753277-G02

44A753278-G02

Supports CCM Slave Protocol

IC695CMM002-AA

IC695CMM004-AA

1.00

N/A

Initial Release

Upgrades

The following upgrade kits may be downloaded from http://www.geautomation.com/support:

Kit Name

IC695CMM002 Kit #

IC695CMM004 Kit #

Notes

FW v2.02 kit

41G2459-FW01-000-A2

41G2460-FW01-000-A2

CMM00x Versions -DF or earlier can only

use v1.xx firmware.

They cannot be updated to v2.xx firmware

due to HW design differences.

FW v2.01 kit

41G2459-FW01-000-A1

41G2460-FW01-000-A1

FW v2.00 kit

41G2459-FW01-000-A0

41G2460-FW01-000-A0

RX3i Serial Communications Modules

GFK-2461N

Compatibility

Programmer Version Requirements

Proficy* Machine Edition Logic Developer 6.00 with SIM 12 or later version is required for DNP3 Unsolicited Response

functionality and Analog Input Event Variation configuration.

Proficy Machine Edition Logic Developer 5.9 SP1 with SIM 6 is required for half duplex flow control

Proficy Machine Edition Logic Developer 5.8 with SIM 2 or newer is required to use SPL

Proficy Machine Edition Logic Developer 5.6 with SIM 10 or newer is required to use DNP3

Proficy Machine Edition Logic Developer 5.6 with SIM 6 or newer is required to use the CMM

CPU Firmware Version Requirements

PACSystems RX3i CPU Version 5.50 or newer is required for SPL

PACSystems RX3i CPU Version 5.00 or newer is required for DNP3 Master to sync its timestamp value with the CPU.

PACSystems RX3i CPU Version 3.83 or newer is required to be able to use the CMM in the RX3i system.

Problems Resolved by Release 2.02

None.

Problems Resolved by Release 2.01

Issue

Description

Defect

#15825

When running a single port in RS232 Serial ASCII mode, communication errors can occur at all baud rates and all data

payload sizes. When running four ports, RS232 Serial ASCII mode, communication errors are seen at baud rates below

4800 baud with payloads of 1024 bytes. With four ports and baud rates below 4800 baud, the payloads of 100 bytes

or less work properly.

New Features for Release 2.02

None

RX3i Serial Communications Modules

GFK-2461N

Restrictions and Open Issues in this Release

SPL

1. The module rejects a SPL program file containing a literal string of length greater than 127. The SPL port will

return a status in the status byte of 61.

2. The static file checker can miss paired NEXT and FOR statements. If a NEXT statement is missing from the

program, execution will continue without looping back to the FOR statement. Users should check their

FOR/NEXT statements before downloading. A missing NEXT statement can also be detected by debugging

using the CLI debug interface.

Other

3. Each port can be configured for DNP3 Master or DNP3 Slave protocol. If any port is configured for DNP3 Master

or Slave, the other ports on the module can only be configured for DNP3 Master or Slave.

4. These modules do not support GE Intelligent Platforms special MODBUS commands for use with a Daniels Flow

Computer.

5. PLC Reference Address and Reference Length parameters only allow bit based memory values that are aligned

to a byte boundary.

For example, for a port using MODBUS Slave with coils mapped to %Q memory, the %Q memory address must

start on a byte boundary in %Q. (Target Address 1 can be mapped to %Q00001 or %Q00009, but it can not be

mapped to %Q00007.)

6. CCM Slave Read Scratchpad operations may fail when a port is configured for CCM Slave protocol and:

▪a new configuration is stored to the PLC using Machine Edition, or

▪the system is power-cycled, or

▪the module is hot-inserted

If the first query received from the CCM Master is a Read Scratchpad request, the module will reject that

request. All subsequent Read Scratchpad requests will be successful unless one of the above conditions occurs

again.

7. The DNP3 slave port has problems using the link layer to validate frame receipt. The DNP3 organization

encourages users not to do this.

8. Change Event Read responses are not sent immediately after a Confirm to an unsolicited response.

If a read request is received after sending an unsolicited response, the slave is required to wait to respond to

the read until either the unsolicited timeout expires, or the unsolicited message is confirmed.

The module waits until the timeout expires, even if the unsolicited message has been confirmed, to send the

read response.

Normally, messages are responded to within milliseconds, but the read response does not occur for up to 2

seconds after the confirm message is sent.

RX3i Serial Communications Modules

GFK-2461N

Operating Notes

•Due to the re-designed nature of the obsolescence change, minor performance differences may exist

between the V1.xx and V2.00 hardware/firmware versions.

SPL

1. In the error message, brackets [ ] are printed only around the key failing token. When looking at the error

message the entire line should be interpreted.

Example:

--- Script file ---

i = 128 )

--- Error output---

Error [3184]: line 1

i = [128] )

2. An SPL wrong error is reported when a “(“ is in an IF statement. IF statements only support comparisons of

variables and constants. Using () to enclose operations (like arithmetic operations or comparisons) will result in

a syntax error. The module will report this error as an unknown identifier for the () symbols rather than a syntax

error.

3. If the SPL program writes to memory that is invalid in the PLC the write will fail and the SPL program will halt.

Other

1. DNP3.0 configurations with Unsolicited Response support enabled or Analog Input Event Variations set to other

than 16 Bit Values Without Time, will result in a System Configuration Mismatch fault. If any of these

configuration is downloaded to a module with firmware earlier than Release 1.34, the module configuration will

fail.

2. The maximum resolution for the MODBUS drop delay is 420μs, so the minimum time for a drop delay is 420μs.

3. If retentive memory is used for Port Control Data, when a power cycle with battery or hot swap of the CMM

module occurs, all exchanges whose control bit is in the ON state will be re-executed on the next PLC output

scan or output DO I/O. To prevent this, all exchange control bits must be cleared by the application logic on the

initial PLC logic scan or upon detection of CMM module removal.

Detailed Documentation

Refer to the PACSystems RX3i System Manual, GFK-2314, for all further details. It may be downloaded at the following

location:

https://ge-ip.force.com/communities/en_US/Documentation/PACSystems-RX3i-System-Manual-GFK-2314-en-US.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unidad de control de GE

GE Multilin MM300 Manual de usuario

GE C-400 Series Manual de usuario

GE Masoneilan VariPak 28001 Manual de usuario

GE ReliaGear LV MCC Manual de usuario

GE IC3645SR4W746N5 Manual de usuario

GE 22158 Manual de usuario

GE MiCOM P40 Agile Manual de usuario

GE PACSystems RX3i IC695ETM001-JW Manual de usuario

GE VersaMax IC200CHS006 Manual de usuario

GE VersaSafe VersaPoint IC220SDL840 Manual de usuario

GE NetworX Series Manual de usuario

GE Reason RT430 Manual de usuario

GE MiCOM P40 Agile Manual de usuario

GE Evolution Series E9000 Manual de usuario

GE Baker Hughes Masoneilan 31000 Series Manual de usuario

GE ATS7310 Instrucciones de montaje

GE IC693CBL300 Manual de usuario

GE WH18X28174 Guía de configuración

GE Masoneilan 469 Series Manual de usuario

GE Tetra 24/24 Manual de usuario

GE CR194 Manual de usuario

GE Masoneilan 77-6 Manual de usuario

GE S-500 Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario